display YAMAHA YZF-R1 2002 Owners Manual

DESCRIPTION
2-3
2
Controls and instruments1. Clutch lever (page 3-13)
2. Left handlebar switches (page 3-11)
3. Multi-function display (page 3-6)
4. Main switch/steering lock (page 3-1)5. Tachometer (page 3-11)
6. Right handlebar switches (page 3-12)
7. Throttle grip (page 6-19)
8. Brake lever (page 3-13)
U5PWE0.book Page 3 Friday, December 7, 2001 5:14 PM

3
INSTRUMENT AND CONTROL FUNCTIONS
Main switch/steering lock ..................................... 3-1
Indicator and warning lights ................................ 3-2
Multi-function display ........................................... 3-6
Tachometer ........................................................ 3-11
Anti-theft alarm (optional) .................................. 3-11
Handlebar switches ........................................... 3-11
Clutch lever ........................................................ 3-13
Shift pedal .......................................................... 3-13
Brake lever ......................................................... 3-13
Brake pedal ........................................................ 3-14
Fuel tank cap ..................................................... 3-14
Fuel .................................................................... 3-15Fuel tank breather hose .................................... 3-16
Catalytic converter ............................................ 3-16
Seats ................................................................. 3-17
Helmet holders .................................................. 3-18
Storage compartment ....................................... 3-19
Adjusting the front fork ...................................... 3-19
Adjusting the shock absorber assembly ............ 3-21
Luggage strap holders ...................................... 3-23
EXUP system .................................................... 3-24
Sidestand .......................................................... 3-24
Ignition circuit cut-off system ............................. 3-25
U5PWE0.book Page 1 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-4
3
EAU04559
Engine speed indicator light
The electrical circuit of the indicator
light can be checked according to the
following procedure.
1. Turn the key to “ON”.
2. If the indicator light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit. (See pages 3-8–
3-10 for a detailed explanation of
the function of this indicator light
and on how to set it.)
EAU04515
Coolant temperature warning light
“”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked according to the fol-
lowing procedure.
1. Turn the key to “ON”.
2. If the warning light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit.
EC000002
CAUTION:_ Do not operate the engine if it is
overheated. _
1. Engine speed indicator light
2. Coolant temperature warning light “”
3. Coolant temperature display
U5PWE0.book Page 4 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-5
3
CB-25E
Coolant
temperatureDisplay Conditions What to do0–39 °C Message “LO” is
displayed.OK. Go ahead with riding.
40–116 °C Temperature is
displayed.OK. Go ahead with riding.
117–139 °C Temperature flashes.
Warning light comes on.Stop the motorcycle and allow it to
idle until the coolant temperature
goes down.
If the temperature does not go
down, stop the engine. (See the
“Engine overheating” section on
page 6-46 for further instructions.)
Above 140 °C Message “HI” flashes.
Warning light comes on.Stop the engine and allow it to cool.
(See the “Engine overheating” sec-
tion on page 6-46 for further in-
structions.)
U5PWE0.book Page 5 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-6
3
EAU04554
Multi-function display The multi-function display is equipped
with the following:

a speedometer (which shows the
riding speed)


an odometer (which shows the to-
tal distance traveled)


two tripmeters (which show the
distance traveled since they were
last set to zero)


a fuel reserve tripmeter (which
shows the distance traveled since
the fuel level warning light came
on)


a clock


a self-diagnosis device


a display brightness and engine
speed indicator light control mode
NOTE:_

Be sure to turn the key to “ON” be-
fore using the “SELECT” and
“RESET” buttons.


For the U.K. only: To switch the
speedometer and odometer/trip-
meter displays between kilome-
ters and miles, press the
“SELECT” button and “RESET”
button together for at least two
seconds.
_
Odometer and tripmeter modes
Pushing the “SELECT” button switches
the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP 1” and “TRIP 2” in the following
order:
ODO
→ TRIP 1
→ TRIP 2
→ ODO
If the fuel level warning light comes on
(see page 3-2), the odometer display
will automatically change to the fuel re-
serve tripmeter mode “F-TRIP” and
start counting the distance traveled
from that point. In that case, pushing
the “SELECT” button switches the dis-
play between the various tripmeter and
odometer modes in the following order:
F-TRIP
→ TRIP 1
→ TRIP 2
→ ODO
→ F-TRIP
1. Multi-function display
2.“SELECT” button
3.“RESET” button
U5PWE0.book Page 6 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-7
3To reset a tripmeter, select it by push-
ing the “SELECT” button, and then
push the “RESET” button for at least
one second. If you do not reset the fuel
reserve tripmeter manually, it will reset
itself automatically and the display will
return to the prior mode after refueling
and traveling 5 km.
Clock mode
Turn the key to “ON”.
To change the display to the clock
mode, push the “SELECT” button for at
least one second.
To change the display back to the prior
mode, push the “SELECT” button.
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “RESET” button to set
the hours.3. Push the “SELECT” button, and
the minute digits will start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
Self-diagnosis device
This model is equipped with a self-di-
agnosis device for various electrical cir-
cuits.
If any of those circuits are defective,
the engine trouble warning light will
come on, and then the multi-function
display will indicate a two-digit error
code (e.g., 11, 12, 13).
If the multi-function display indicates
such an error code, note the code num-
ber, and then have a Yamaha dealer
check the motorcycle.
ECA00127
CAUTION:_ If the display indicates an error
code, the motorcycle should be
checked as soon as possible in or-
der to avoid engine damage. _
U5PWE0.book Page 7 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-8
3
Display brightness and engine
speed indicator light control mode
This mode cycles through five control
functions, allowing you to make the fol-
lowing settings in the order listed be-
low.
1. Display brightness: This function
allows you to adjust the brightness
of the multi-function display to suit
the outside lighting conditions.2. Engine speed indicator light activi-
ty: This function allows you to
choose whether or not the indica-
tor light should be activated and
whether it should blink or stay on
when activated.
3. Engine speed indicator light acti-
vation: This function allows you to
select the engine speed at which
the indicator light will be activated.
4. Engine speed indicator light deac-
tivation: This function allows you
to select the engine speed at
which the indicator light will be de-
activated.
5. Engine speed indicator light
brightness: This function allows
you to adjust the brightness of the
indicator light to suit your prefer-
ence.
NOTE:_

To make any settings in this mode,
you have to cycle through all of its
functions. However, if the key is
turned to “OFF” or the engine is
started before completing the pro-
cedure, only the settings made be-
fore the “SELECT” button was last
pushed will be applied.


In this mode, the multi-function
display shows the current setting
for each function (except the en-
gine speed indicator light activity
function).
_
1. Engine speed indicator light
2.“SELECT” button
3.“RESET” button
U5PWE0.book Page 8 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-9
3To adjust the display brightness
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but-
ton.
3. Turn the key to “ON”, and then, af-
ter five seconds, release the
“SELECT” button.
4. Push the “RESET” button to select
the desired display brightness lev-
el.
5. Push the “SELECT” button to con-
firm the selected display bright-
ness level. The control mode
changes to the engine speed indi-
cator light activity function.To set the engine speed indicator light
activity function1. Push the “RESET” button to select
one of the following indicator light
activity settings:
a. The indicator light will stay on
when activated. (This setting is se-
lected when the indicator light
stays on.)
b. The indicator light will flash when
activated. (This setting is selected
when the indicator light flashes
four times per second.)
c. The indicator light is deactivated;
in other words, it will not come on
or flash. (This setting is selected
when the indicator light flashes
once every two seconds.)
2. Push the “SELECT” button to con-
firm the selected indicator light ac-
tivity. The control mode changes
to the engine speed indicator light
activation function.To set the engine speed indicator light
activation functionNOTE:_ The indicator light activation function can
be set between 7,000 and 12,000 r/min
in increments of 500 r/min. _1. Push the “RESET” button to select
the desired engine speed for acti-
vating the indicator light.
2. Push the “SELECT” button to con-
firm the selected engine speed.
The control mode changes to the
engine speed indicator light deac-
tivation function.
U5PWE0.book Page 9 Friday, December 7, 2001 5:14 PM

INSTRUMENT AND CONTROL FUNCTIONS
3-10
3 To set the engine speed indicator light
deactivation functionNOTE:_

The indicator light deactivation
function can be set between 7,000
and 12,000 r/min in increments of
500 r/min.


Be sure to set the deactivation
function to a higher engine speed
than for the activation function,
otherwise the engine speed indi-
cator light will remain deactivated.
_1. Push the “RESET” button to select
the desired engine speed for de-
activating the indicator light.
2. Push the “SELECT” button to con-
firm the selected engine speed.
The control mode changes to the
engine speed indicator light bright-
ness function.To adjust the engine speed indicator
light brightness1. Push the “RESET” button to select
the desired indicator light bright-
ness level.
2. Push the “SELECT” button to con-
firm the selected indicator light
brightness level. The multi-func-
tion display will return to the odom-
eter, tripmeter or clock mode.
U5PWE0.book Page 10 Friday, December 7, 2001 5:14 PM

INDEXAAir filter element, replacing ..................... 6-16
Anti-theft alarm ...................................... 3-11BBattery ................................................... 6-33
Brake and clutch levers,
checking and lubricating ...................... 6-30
Brake fluid, changing ............................. 6-27
Brake fluid level, checking...................... 6-26
Brake lever............................................. 3-13
Brake light switch (rear), adjusting ......... 6-24
Brake pads, checking............................. 6-25
Brake pedal............................................ 3-14
Brake pedal, lubricating.......................... 6-31
Brake pedal position, adjusting .............. 6-24CCables, checking and lubricating............ 6-29
Care.........................................................7-1
Catalytic converter ................................. 3-16
Clutch lever ............................................ 3-13
Clutch lever free play, adjusting ............. 6-23
Conversion table ......................................8-5
Coolant .................................................. 6-12
Changing .......................................... 6-13
Checking .......................................... 6-12
Coolant temperature warning light............3-4
Cowlings and panels,
removing and installing ..........................6-5
DDimmer switch ....................................... 3-11
Drive chain, lubricating .......................... 6-29
Drive chain slack ................................... 6-27
Adjusting .......................................... 6-28
Checking .......................................... 6-27EEngine break-in ....................................... 5-3
Engine oil and oil filter cartridge ............... 6-9
Engine speed indicator light..................... 3-4
Engine stop switch................................. 3-12
Engine trouble warning light .................... 3-3
EXUP system ........................................ 3-24FFront fork, adjusting ............................... 3-19
Front fork, checking ............................... 6-31
Fuel ....................................................... 3-15
Fuel consumption, tips for reducing ......... 5-3
Fuel level warning light ............................ 3-2
Fuel tank breather hose ......................... 3-16
Fuel tank cap ......................................... 3-14
Fuses, replacing .................................... 6-35HHandlebar switches ............................... 3-11
Headlight bulb, replacing ....................... 6-36
Helmet holders ...................................... 3-18
High beam indicator light ......................... 3-3
Horn switch ........................................... 3-12
IIdentification numbers ..............................9-1
Idling speed, adjusting ...........................6-18
Ignition circuit cut-off system ..................3-25
Indicator and warning lights......................3-2KKey identification number .........................9-1LLicense plate light bulb, replacing...........6-38
Light switch .............................................. 3-12
Luggage strap holders ...........................3-23MMain switch/steering lock .........................3-1
Model label ..............................................9-2
Multi-function display................................3-6NNeutral indicator light ...............................3-3OOil level warning light ...............................3-3PParking.....................................................5-4
Part locations ...........................................2-1
Pass switch ............................................3-11
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list ............................4-1
U5PWE0.book Page 1 Friday, December 7, 2001 5:14 PM