fuse YAMAHA YZF-R1S 2004 User Guide

8-1
8
ELECTRICAL COMPONENTSELEC
9Oil level switch
10Radiator fan motor
11Horn
12Ignition coil
1Main switch
2Front brake light switch
3Starter relay
4Battery
5Fuse box
6Rear brake light switch
7Neutral switch
8Sidestand switch
EAS00729
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS
ProCarManuals.com

8-4
11Neutral switch
12Rear brake light switch
13Fuse box
1Main switch
2Horn switch
3Dimmer switch
4Turn signal switch
5Clutch switch
6Sidestand switch
7Engine stop switch
8Front brake light switch
9Start switch
10Oil level switch
CHECKING THE SWITCHESELEC
EAS00731
CHECKING THE SWITCHES
Check each switch for damage or wear, proper connections, and also for continuity between the termi-
nals. Refer to “CHECKING SWITCH CONTINUITY”.
Damage / wear
Repair or replace.
Improperly connected
Properly connect.
Incorrect continuity reading
Replace the switch.
ProCarManuals.com

8-9
IGNITION SYSTEMELEC
1Main switch
4Fuse (main)
6Battery
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
14E.C.U.
15Ignition coil #1
16Ignition coil #2
17Ignition coil #3
18Ignition coil #4
19Spark plug
31Crankshaft position sensor
35Cylinder identification sensor
36Lean angle cut-off switch
53Engine stop switch
59Clutch switch
73Fuse (ignition)
ProCarManuals.com

8-10
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
YESNO
EAS00741
3. Spark plugs
The following procedure applies to all of the
spark plugs.

Check the condition of the spark plug.

Check the spark plug type.

Measure the spark plug gap.
Refer to “CHECKING THE SPARK PLUGS”
in chapter 3.
Standard spark plug
CR9EK (NGK)
Spark plug gap
0.6  0.7 mm (0.0236  0.0276 in)

Is the spark plug in good condition, is it of the
correct type, and is its gap within specifica-
tion?
Re-gap or replace
the spark plug.
IGNITION SYSTEMELEC
NOTE:
YESNO
1. Main and ignition fuses

Check the main and ignition fuses for conti-
nuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main and ignition fuses OK?
Replace the fuse(s).
EAS00737
TROUBLESHOOTING
The ignition system fails to operate (no
spark or intermittent spark).
Check:
1. main and ignition fuses
2. battery
3. spark plugs
4. ignition spark gap
5. ignition coil resistance
6. crankshaft position sensor
7. main switch
8. engine stop switch
9. neutral switch
10. sidestand switch
11. clutch switch
12. starting circuit cut-off relay (diode)
13. lean angle cut-off switch
14. wiring connections
(of the entire ignition system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Ignition checker
90890-06754
Dynamic spark tester
YM-34487
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-14
1Main switch
4Fuse (main)
6Battery
8Starter relay
9Starter motor
10Starting circuit cut-off relay
11Neutral switch
12Sidestand switch
53Engine stop switch
54Start switch
73Fuse (ignition)
ELECTRIC STARTING SYSTEMELEC
EAS00755
ELECTRIC STARTING SYSTEM
CIRCUIT DIAGRAM
ProCarManuals.com

8-15
ELECTRIC STARTING SYSTEMELEC
EAS00756
STARTING CIRCUIT CUT-OFF SYSTEM
OPERATION
If the engine stop switch is set to “
” and the
main switch is set to “ON” (both switches are
closed), the starter motor can only operate if at
least one of the following conditions is met:

The transmission is in neutral (the neutral
switch is closed).

The clutch lever is pulled to the handlebar (the
clutch switch is closed) and the sidestand is up
(the sidestand switch is closed).
The starting circuit cut-off relay prevents the
starter motor from operating when neither of
these conditions has been met. In this instance,
the starting circuit cut-off relay is open so cur-
rent cannot reach the starter motor. When at
least one of the above conditions has been met
the starting circuit cut-off relay is closed and the
engine can be started by pressing the starter
switch.
WHEN THE TRANSMISSION IS IN
NEUTRAL
WHEN THE SIDESTAND IS UP AND
THE CLUTCH LEVER IS PULLED TO
THE HANDLEBAR
1Battery
2Main fuse
3Main switch
4Ignition fuse
5Engine stop switch
6Starting circuit cut-off relay
7Diode
8Clutch switch
9Sidestand switch
10Neutral switch
11Start switch
12Starter relay
13Starter motor
ProCarManuals.com

8-16
YESNO
3. Starter motor

Connect the positive battery terminal and
starter motor lead with a jumper lead .
Repair or replace the
starter motor.
A wire that is used as a jumper lead
must have at least the same capacity or
more as that of the battery lead, other-
wise the jumper lead may burn.

This check is likely to produce sparks,
therefore make sure nothing flammable
is in the vicinity.

Does the starter motor turn?
WARNING
1
23
EAS00758
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
ELECTRIC STARTING SYSTEMELEC
NOTE:
YESNO
1. Main and ignition fuses

Check the main and ignition fuses for conti-
nuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main and ignition fuses OK?
Replace the fuse(s).
EAS00757
TROUBLESHOOTING
The starter motor fails to turn.
Check:
1. main and ignition fuses
2. battery
3. starter motor
4. starting circuit cut-off relay
5. starter relay
6. main switch
7. engine stop switch
8. neutral switch
9. sidestand switch
10. clutch switch
11. start switch
12. wiring connections
(of the entire starting system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings
4. throttle body assembly

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-24
2A.C. magneto
3Rectifier / regulator
4Fuse (main)
6Battery
CHARGING SYSTEMELEC
EAS00773
CHARGING SYSTEM
CIRCUIT DIAGRAM
ProCarManuals.com

8-25
NOYES
3. Charging voltage

Set the engine tachometer to the ignition coil
of cylinder #1.

Connect the pocket tester (DC 20 V) to the
battery as shown.
The charging circuit
is OK. Positive tester probe

positive battery terminal
Negative tester probe

negative battery terminal

Start the engine and let it run at approxi-
mately 5,000 r / min.

Measure the charging voltage.
Charging voltage
14 V at 5,000 r / min

Is the charging voltage within specification?
EAS00775
YESNO

Clean the battery
terminals.

Recharge or re-
place the battery.
Make sure the battery is fully charged.
NOTE:
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?
CHARGING SYSTEMELEC
NOTE:
YESNO
1. Main fuse

Check the main fuse for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Is the main fuse OK?
Replace the fuse.
2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
EAS00739 EAS00774
TROUBLESHOOTING
The battery is not being charged.
Check:
1. main fuse
2. battery
3. charging voltage
4. stator coil lead
5. stator coil resistance
6. wiring connections
(of the entire charging system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com

8-28
LIGHTING SYSTEMELEC
1Main switch
4Fuse (main)
6Battery
14E.C.U.
46Hi beam indicator light
49Meter light
57Dimmer switch
62Front turn signal/position light (left)
63Front turn signal/position light (right)
66Headlight
67Auxiliary light
68License plate light
69Rear brake light switch
70Tail/brake light
71Headlight relay (on / off)
72Headlight relay (dimmer)
74Fuse (signal)
75Fuse (headlight)
ProCarManuals.com