light YAMAHA YZF-R1S 2004 Service Manual
Page 9 of 457
CHASSIS3-42 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE FRONT BRAKE 3-42. . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE REAR BRAKE 3-43. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE BRAKE FLUID LEVEL 3-44. . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE REAR BRAKE LIGHT SWITCH 3-45. . . . . . . . . . . . .
CHECKING THE FRONT AND REAR BRAKE PADS 3-45. . . . . . . . . . .
CHECKING THE FRONT AND REAR BRAKE HOSES 3-46. . . . . . . . .
BLEEDING THE HYDRAULIC BRAKE SYSTEM 3-47. . . . . . . . . . . . . . .
ADJUSTING THE SHIFT PEDAL 3-48. . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE DRIVE CHAIN SLACK 3-49. . . . . . . . . . . . . . . . . . . . .
LUBRICATING THE DRIVE CHAIN 3-50. . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE STEERING HEAD 3-51. . . . . . . . .
CHECKING THE FRONT FORK 3-53. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE FRONT FORK LEGS 3-54. . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE REAR SHOCK ABSORBER ASSEMBLY 3-56. . . . .
CHECKING THE TIRES 3-58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE WHEELS 3-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND LUBRICATING THE CABLES 3-61. . . . . . . . . . . . . . .
LUBRICATING THE LEVERS AND PEDALS 3-61. . . . . . . . . . . . . . . . . .
LUBRICATING THE SIDESTAND 3-61. . . . . . . . . . . . . . . . . . . . . . . . . . . .
LUBRICATING THE REAR SUSPENSION 3-61. . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEM3-62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND CHARGING THE BATTERY 3-62. . . . . . . . . . . . . . . . .
CHECKING THE FUSES 3-67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPLACING THE HEADLIGHT BULBS 3-69. . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE HEADLIGHT BEAMS 3-70. . . . . . . . . . . . . . . . . . . . . .
CHAPTER 4
CHASSIS
FRONT WHEEL AND BRAKE DISCS4-1 . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE FRONT WHEEL 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE FRONT WHEEL 4-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE BRAKE DISCS 4-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE FRONT WHEEL 4-6. . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE FRONT WHEEL STATIC BALANCE 4-7. . . . . . . . .
REAR WHEEL AND BRAKE DISC4-9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR WHEEL 4-9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REAR BRAKE DISC AND REAR WHEEL SPROCKET 4-10. . . . . . . . .
REMOVING THE REAR WHEEL 4-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE REAR WHEEL 4-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE REAR WHEEL DRIVE HUB 4-13. . . . . . . . . . . . . . . . .
CHECKING AND REPLACING THE REAR WHEEL
SPROCKET 4-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE REAR WHEEL 4-14. . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADJUSTING THE REAR WHEEL STATIC BALANCE 4-14. . . . . . . . . . .
ProCarManuals.com
Page 15 of 457
CHECKING THE CONDITION OF THE BULB SOCKETS 8-6. . . . . . .
CHECKING THE LEDs 8-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM8-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRIC STARTING SYSTEM8-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING CIRCUIT CUT-OFF SYSTEM OPERATION 8-15. . . . . . . . .
TROUBLESHOOTING 8-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTER MOTOR8-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE STARTER MOTOR 8-21. . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLING THE STARTER MOTOR 8-22. . . . . . . . . . . . . . . . . . . . . .
CHARGING SYSTEM8-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LIGHTING SYSTEM8-27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE LIGHTING SYSTEM 8-31. . . . . . . . . . . . . . . . . . . . . . . .
SIGNALING SYSTEM8-34 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE SIGNALING SYSTEM 8-36. . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM8-43 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL PUMP SYSTEM8-48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 8-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL PUMP SYSTEM 8-49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE FUEL PUMP 8-52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SELF-DIAGNOSIS8-53 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING 8-54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 9
TROUBLESHOOTING
STARTING FAILURES9-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com
Page 16 of 457
ELECTRICAL SYSTEMS 9-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INCORRECT ENGINE IDLING SPEED9-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEMS 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POOR MEDIUM-AND-HIGH-SPEED PERFORMANCE9-2 . . . . . . . . . . . . .
ENGINE 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM 9-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAULTY GEAR SHIFTING9-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHIFTING IS DIFFICULT 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHIFT PEDAL DOES NOT MOVE 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . .
JUMPS OUT OF GEAR 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAULTY CLUTCH9-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH SLIPS 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH DRAGS 9-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OVERHEATING9-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUEL SYSTEM 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHASSIS 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRICAL SYSTEMS 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OVERCOOLING9-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM 9-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POOR BRAKING PERFORMANCE9-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAULTY FRONT FORK LEGS9-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LEAKING OIL 9-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MALFUNCTION 9-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNSTABLE HANDLING9-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAULTY LIGHTING OR SIGNALING SYSTEM9-6 . . . . . . . . . . . . . . . . . . . .
HEADLIGHT DOES NOT COME ON 9-6. . . . . . . . . . . . . . . . . . . . . . . . . .
HEADLIGHT BULB BURNT OUT 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TAIL / BRAKE LIGHT DOES NOT COME ON 9-6. . . . . . . . . . . . . . . . . . .
TAIL / BRAKE LIGHT BULB BURNT OUT 9-6. . . . . . . . . . . . . . . . . . . . . .
TURN SIGNAL DOES NOT COME ON 9-6. . . . . . . . . . . . . . . . . . . . . . . .
TURN SIGNAL BLINKS SLOWLY 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURN SIGNAL REMAINS LIT 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURN SIGNAL BLINKS QUICKLY 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . .
HORN DOES NOT SOUND 9-6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com
Page 18 of 457
1-2
1
1 Clock
2 Speedometer
3 “SELECT” button
4 “RESET” button
5 Tachometer
6 Coolant temperature display / air intake
temperature display
7 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
8 Shift timing indicator light
1 Clock
2 Speedometer
FEATURES
GEN
INFO
NOTE:
EAS00019
FEATURES
INSTRUMENT FUNCTIONS
Multi-function display
The multi-function meter unit is equipped with
the following:
a speedometer (which shows the riding
speed)
a tachometer (witch shows engine speed)
an odometer (which shows the total distance
traveled)
two tripmeters (which show the distance
traveled since they were last set to zero)
a fuel reserve tripmeter (which shows the
distance traveled since the fuel level warning
light came on)
a stopwatch
a clock
a coolant temperature display
an air intake temperature display
a self-diagnosis device
a display brightness and shift timing indicator
light control mode
Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
Clock mode
Turn the key to “ON”.
To set the clock
1. Push the “SELECT” button and “RESET”
button together for at least two seconds.
2. When the hour digits start flashing, push the
“RESET” button to set the hours.
3. Push the “SELECT” button, and the minute
digits will start flashing.
4. Push the “RESET” button to set the minutes.
5. Push the “SELECT” button and then release
it to start the clock.
ProCarManuals.com
Page 19 of 457
1-3
FEATURES
GEN
INFO
1 Coolant temperature display / air intake
temperature display
2 Odometer / tripmeters / fuel reserve tripme-
ter / stopwatch
3 Shift timing indicator light
NOTE:
NOTE:Odometer, tripmeter, and stopwatch modes
Push the “SELECT” button to switch the display
between the odometer mode “ODO”, the trip-
meter modes “TRIP A” and “TRIP B” and the
stopwatch mode in the following order:
TRIP A TRIP B ODO Stopwatch
TRIP A
If the fuel level warning light comes on, the
odometer display will automatically change to
the fuel reserve tripmeter mode ”F-TRIP” and
start counting the distance traveled from that
point. In that case, push the ”SELECT” button to
switch the display between the various tripme-
ter, odometer, and stopwatch modes in the fol-
lowing order:
F-TRIP Stopwatch TRIP A TRIP B
ODO F-TRIP
To reset a tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RESET” button
for at least one second. If you do not reset the fuel
reserve tripmeter manually, it will reset itself auto-
matically and the display will return to the prior
mode after refueling and traveling 5 km (3 mi).
Stopwatch mode
Standard measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “SELECT” button to stop the stopwatch.
3. Push the “SELECT” button again to reset the stopwatch.
Split-time measurement
1. Push the “RESET” button to start the stopwatch.
2. Push the “RESET” button to measure split-times. (The colon “:” will start flashing.)
3. Push the “RESET” button to display the final split-time or push the “SELECT” button to stop the stop-
watch and display total elapsed time.
4. Push the “SELECT” button to reset the stopwatch.
Coolant temperature display
The coolant temperature display indicates the temperature of the coolant. Push the “RESET” button to
switch the coolant temperature display to the air intake temperature display.
When the coolant temperature display is selected, “C” is displayed before the coolant temperature.
Air intake temperature display
The air intake temperature display indicates the temperature of the air drawn into the air filter case. Push
the “RESET” button to switch the coolant temperature display to the air intake temperature display.
Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes
on when the engine overheats.
When the key is turned to “ON”, the coolant temperature is automatically displayed, even if the air
intake temperature was displayed prior to turning the key to “OFF”.
When the air intake temperature display is selected, “A” is displayed before thetemperature.
ProCarManuals.com
Page 20 of 457
1-4
FEATURES
GEN
INFO
NOTE: Self-diagnosis devices
The model is equipped with a self-diagnosis device for various electrical circuits. If any of those circuits
are defective, the engine trouble warning light will come on, and then the right display will indicate a
two-digit error code (e.g.,11,12,13).
Display brightness and shift timing indicator light control mode
This mode cycles through five control functions, allowing you to make the following settings in the order
listed below.
Display brightness:
This function allows you to adjust the brightness of the displays and tachometer to suit the outside
lighting conditions.
Shift timing indicator light activity:
This function allows you to choose whether or not the indicator light should be activated and whether
it should flash or stay on when activated.
Shift timing indicator light activation:
This function allows you to select the engine speed at which the indicator light will be activated.
Shift timing indicator light deactivation:
This function allows you to select the engine speed at which the indicator light will be deactivated.
Shift timing indicator light brightness:
This function allows you to adjust the brightness of the indicator light to suit your preference.
To make any settings in this mode, you have to cycle through all of its functions. However, if the key is
turned to “OFF” or the engine is started before completing the procedure, only the settings made be-
fore the “SELECT” button was last pushed will be applied.
In this mode, the right display shows the current setting for each function (except the shift timing indi-
cator light activity function).
To adjust the brightness of the multifunction meter displays and tachometer
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” button.
3. Turn the key to “ON”, and then release the “SELECT” button after five seconds.
4. Push the “RESET” button to select the desired brightness level.
5. Push the “SELECT” button to confirm the selected brightness level. The control mode changes to
the shift timing indicator light activity function.
To set the shift timing indicator light activity function
1. Push the “RESET” button to select one of the following indicator light activity settings:
The indicator light will stay on when activated. (This setting is selected when the indicator light stays
on.)
The indicator light will flash when activated. (This setting is selected when the indicator light flashes
four times per second.)
The indicator light is deactivated; in other words, it will not come on or flash. (This setting is selected
when the indicator light flashes once every two seconds.)
2. Push the ”SELECT” button to confirm the selected indicator light activity. The control mode changes
to the shift timing indicator light activation function.
ProCarManuals.com
Page 21 of 457
1-5
FEATURES
GEN
INFO
NOTE:
NOTE: To set the shift timing indicator light activation function
The shift timing indicator light activation function can be set between 7000 r/min and 15000 r/m. From
7000 r/min to 12000 r/min, the indicator light can be set in increments of 500 r/min. From 12000 r/min to
15000 r/min, the indicator light can be set in increments of 200 r/min.
1. Push the “RESET” button to select the desired engine speed for activating the indicator light.
2. Push the “SELECT” button to confirm the selected engine speed. The control mode changes to the
shift timing indicator light deactivation function.
To set the shift timing indicator light deactivation function
The shift timing indicator light activation function can be set between 7000 r/min and 15000 r/min.
From 7000 r/min to 12000 r/min, the indicator light can be set in increments of 500 r/min. From 12000
r/min to 15000 r/min, the indicator light can be set in increments of 200 r/min.
Be sure to set the deactivation function to a higher engine speed than for the activation function,
otherwise the shift timing indicator light will remain deactivated.
1. Push the “RESET” button to select the desired engine speed for deactivating the indicator light.
2. Push the “SELECT” button to confirm the selected engine speed. The control mode changes to the
shift timing indicator light brightness function.
To adjust the shift timing indicator light brightness
1. Push the “RESET” button to select the desired indicator light brightness level.
2. Push the “SELECT” button to confirm the selected indicator light brightness level. The right display
will return to the odometer or tripmeter mode
ProCarManuals.com
Page 23 of 457
1-7
IMPORTANT INFORMATION
GEN
INFO
CAUTION:
EAS00023
LOCK WASHERS / PLATES AND COTTER
PINS
After removal, replace all lock washers / plates
1 and cotter pins. After the bolt or nut has been
tightened to specification, bend the lock tabs
along a flat of the bolt or nut.
EAS00024
BEARINGS AND OIL SEALS
Install bearings and oil seals so that the
manufacturer’s marks or numbers are visible.
When installing oil seals, lubricate the oil seal
lips with a light coat of lithium-soap-based
grease. Oil bearings liberally when installing, if
appropriate.
1Oil seal
Do not spin the bearing with compressed air
because this will damage the bearing sur-
faces.
1Bearing
EAS00025
CIRCLIPS
Before reassembly, check all circlips carefully
and replace damaged or distorted circlips. Al-
ways replace piston pin clips after one use.
When installing a circlip
1, make sure the
sharp-edged corner
2 is positioned opposite
the thrust
3 that the circlip receives.
4Shaft
ProCarManuals.com
Page 43 of 457
2-15
ELECTRICAL SPECIFICATIONSSPEC
ELECTRICAL SPECIFICATIONS
ItemStandardLimit
System voltage12 V
Ignition system
Ignition system type
Ignition timing
Crankshaft position sensor
resistance / color
T.C.I. unit model (manufacturer)
DC. T.C.I.
5 BTDC at 1,050 r / min
336 504 Ω at 20C (68F) / Gy-B
F8T822 (MITSUBISHI) (USA)
F8T823 (MITSUBISHI) (CAL)
Ignition coils
Model (manufacturer)
Minimum ignition spark gap
Primary coil resistance
Secondary coil resistance
F6T558 (MITSUBISHI)
6 mm (0.24 in)
1.19 1.61 Ω at 20C (68F)
8.5 11.5 kΩ at 20C (68F)
Charging system
System type
Model (manufacturer)
Normal output
Stator coil resistance / color
A.C. magneto
F4T850 (MITSUBISHI)
14 V / 560 W at 5,000 r / min
0.14 0.18 Ω at 20C (68F) / W-W
Rectifier / regulator
Regulator type
Model (manufacture)
Semi conductor short circuit
FH011AA (SHINDENGEN)
()
No-load regulated voltage
Rectifier capacity
Withstand voltage
()
14.3 15.1 V
50 A
100 V
Battery
Battery type
Battery voltage / capacity
Specific gravity
Manufacturer
Ten hour rate amperage
YTZ10S
12 V / 8.6 Ah
1.310
YUASA
0.8 A
Headlight typeHalogen bulb
Bulbs (voltage / wattage quantity)
Headlight
Auxiliary light
Tail / brake light
Front turn signal light / position light
Rear turn signal light
Licence plate light
Meter light
12 V 55 W 4
12 V 5 W 2
LED 1
12 V 21 W / 5 W 2
12 V 21 W 2
12 V 5 W 1
LED 1
ProCarManuals.com
Page 44 of 457
2-16
ELECTRICAL SPECIFICATIONSSPEC
ItemStandardLimit
Indicator light
(voltage / wattage quantity)
Neutral indicator light
High beam indicator light
Oil level warning light
Turn signal indicator light
Fuel level warning light
Coolant temparture indicator light
Engine trouble warning light
Shift timing indicator light
LED 1
LED 1
LED 1
LED 2
LED 1
LED 1
LED 1
LED 1
Electric starting system
System type
Starter motor
Model (manufacturer)
Power output
Brushes
Overall length
Spring force
Armature coil resistance
Commutator diameter
Mica undercut
Constant mesh
5VY (YAMAHA)
0.9 kW
10.8 mm (0.43 in)
5.28 7.92 N (538 808 g,
18.99 28.48 oz)
0.0090 0.0110 Ω at 20C (68F)
24.5 mm (0.96 in)
1.5 mm (0.06 in)
3.6 mm
(0.14 in)
23.5 mm
(0.93 in)
Starter relay
Model (manufacturer)
Amperage
Coil resistance
2768079-A (JIDECO)
180 A
4.18 4.62 Ω at 20C (68F)
Horn
Horn type
Model (manufacturer) quantity
Max. amperage
Performance
Coil resistance
Plane
YF-12 (NIKKO) 1
3 A
105 113 db / 2 m
1.15 1.25 Ω at 20C (68F)
Turn signal relay
Relay type
Model (manufacturer)
Self-cancelling device built-in
Turn signal blinking frequency
Wattage
Full transistor
FE218BH (DENSO)
No
75 95 cycles / min.
21 W 2 + 3.4 W
Oil level switch
Model (manufacturer)
5VY (SOMIC ISHIKAWA)
EXUP servo motor
Model (manufacturer)
5VY (YAMAHA)
ProCarManuals.com