radiator YAMAHA YZF-R1SC 2004 Owner's Manual

6-2
6
RADIATORCOOL
Order Job / Part Q’ty Remarks
6
7
8
9
10
11Radiator inlet pipe
Oil cooler outlet hose
Water pump breather hose
Radiator outlet hose
Water pump inlet pipe
O-ring1
1
1
1
1
1
For installation, reverse the removal
procedure.
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
5 Nm (0.5 m
kg, 3.6 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
ProCarManuals.com

6-3
RADIATORCOOL
NOTE:
EAS00455
CHECKING THE RADIATOR
1. Check:

radiator fins
Obstruction
Clean.
Apply compressed air to the rear of the radia-
tor.
Damage
Repair or replace.
Straighten any flattened fins with a thin, flat-
head screwdriver.
2. Check:

radiator hoses

radiator pipes
Cracks / damage
Replace.
3. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Radiator cap opening pressure
108
137 kPa
(1.08
1.37 kg / cm
2,
1.0
1.3 bar, 15.6
19.9 psi)
a. Install the radiator cap tester
1 and radiator
cap tester adapter
2 to the radiator cap 3.
Radiator cap tester
90890-01325, YU-24460-01
Radiator cap tester adapter
90890-01352, YU-33984
b. Apply the specified pressure for ten seconds
and make sure there is no drop in pressure.
4. Check:

radiator fan
Damage
Replace.
Malfunction
Check and repair.
Refer to “COOLING SYSTEM” in chapter 8.
ProCarManuals.com

6-4
RADIATORCOOL
EAS00456
INSTALLING THE RADIATOR
1. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” in
chapter 3.
2. Check:

cooling system
Leaks
Repair or replace any faulty part.
3. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Refer to “CHECKING THE RADIATOR”.
ProCarManuals.com

6-7
OIL COOLERCOOL
63 Nm (6.3 m
kg, 46 ft
lb)
NOTE:
EAS00458
CHECKING THE OIL COOLER
1. Check:

oil cooler
Cracks / damage
Replace.
2. Check:

oil cooler inlet hose

oil cooler outlet hose
Cracks / damage / wear
Replace.
EAS00459
INSTALLING THE OIL COOLER
1. Clean:

mating surfaces of the oil cooler and the
crankcase
(with a cloth dampened with lacquer thinner)
2. Install:

O-ring
New

oil cooler
1

washer 2 New

bolt
3

Before installing the oil cooler, lubricate the oil
cooler bolt and O-ring with a thin coat of engine
oil.

Make sure that the O-ring is positioned proper-
ly.

Align the projection
a on the oil cooler with the
slot
b in the crankcase.
3. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” in
chapter 3.

crankcase
(with the specified amount of the recom-
mended engine oil)
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Check:

cooling system
Leaks
Repair or replace any faulty part.
5. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Refer to “CHECKING THE RADIATOR”.
ProCarManuals.com

6-11
THERMOSTATCOOL
10 Nm (1.0 m
kg, 7.2 ft
lb)
NOTE:
EAS00464
ASSEMBLING THE THERMOSTAT
ASSEMBLY
1. Install:

thermostat housing
1

thermostat 2

O-ring New 3

thermostat housing cover 4
Install the thermostat with its breather hole a
facing up.
EAS00466
INSTALLING THE THERMOSTAT
ASSEMBLY
1. Fill:

cooling system
(with the specified amount of the recom-
mended coolant)
Refer to “CHANGING THE COOLANT” in
chapter 3.
2. Check:

cooling system
Leaks
Repair or replace any faulty part.
3. Measure:

radiator cap opening pressure
Below the specified pressure
Replace the
radiator cap.
Refer to “CHECKING THE RADIATOR”.
ProCarManuals.com

7-13
FUEL INJECTION SYSTEMFI
Diagnostic
codeItemDescription of actionData displayed on meter
(reference value)
32
Ignition coil #3After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #3 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
33
Ignition coil #4After the engine stop switch has been turned from OFF to
ON, it actuates ignition coil #4 for five times every second
and illuminates the engine trouble warning light.
* Connect an ignition checker.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check that spark is generated,
5 times with the engine stop
switch ON.
36
Injector #1After the engine stop switch has been turned from OFF to
ON, it actuates the injector #1 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
37
Injector #2After the engine stop switch has been turned from OFF to
ON, it actuates the injector #2 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
38
Injector #3After the engine stop switch has been turned from OFF to
ON, it actuates the injector #3 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
39
Injector #4After the engine stop switch has been turned from OFF to
ON, it actuates the injector #4 five times every second and
illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the injector five times with
engine stop switch ON.
48
AI system solenoidAfter the engine stop switch has been turned from OFF to
ON, it actuates the AI system solenoid five times every
second and illuminates the engine trouble warning light.
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the operating sound of
the AI system solenoid 5 times
with the engine stop
switch ON.
50
Fuel injection system
relayAfter the engine stop switch has been turned from OFF to
ON, it actuates the fuel injection system relay five times
every second and illuminates the engine trouble warning
light (the light is OFF when the relay is ON, and the light is
ON when the relay is OFF).
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the fuel injection system
relay operating sound 5 times
with the engine stop
switch ON.
51
Radiator fan motor
relayAfter the engine stop switch has been turned from OFF to
ON, it actuates the radiator fan motor relay five times every
5 seconds and illuminates the engine trouble warning light.
(ON 2 seconds, OFF 3 seconds)
* If the engine stop switch is ON, turn it OFF once, and then
turn it back ON.Check the radiator fan motor
relay operating sound 5 times
with the engine stop
switch ON.
(At that time, the fan motor
rotates.)
ProCarManuals.com

8-1
8
ELECTRICAL COMPONENTSELEC
9Oil level switch
10Radiator fan motor
11Horn
12Ignition coil
1Main switch
2Front brake light switch
3Starter relay
4Battery
5Fuse box
6Rear brake light switch
7Neutral switch
8Sidestand switch
EAS00729
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS
ProCarManuals.com

8-2
9Radiator fan motor relay
10Turn signal relay
11Rectifier / regulator
12Throttle position sensor
13Sub-throttle position sensor
1Coolant temperature sensor
2Intake air temperature sensor
3Intake air pressure sensor
4Fuel pump
5ECU
6Lean angle cut-off switch
7Starting circuit cut-off relay
8Headlight relay (dimmer)
ELECTRICAL COMPONENTSELEC
ProCarManuals.com

8-44
1Main switch
4Fuse (main)
6Battery
14E.C.U.
28Coolant temperature sensor
73Fuse (ignition)
76Radiator fan motor relay
77Fuse (radiator fan motor left)
78Fuse (radiator fan motor right)
79Radiator fan motor 2
80Radiator fan motor 1
COOLING SYSTEMELEC
ProCarManuals.com

8-45
YESNO 2. Battery

Check the condition of the battery.
Refer to “CHECKING AND CHARGING
THE BATTERY” in chapter 3.
Minimum open-circuit voltage
12.8 V or more at 20C (68F)

Is the battery OK?

Clean the battery
terminals.

Recharge or re-
place the battery.
EAS00739
EAS00749
3. Main switch

Check the main switch for continuity.
Refer to “CHECKING THE SWITCHES”.

Is the main switch OK?
YESNO
Replace the main
switch.
COOLING SYSTEMELEC
NOTE:
YESNO
1. Main, ignition and radiator fan motor fuses

Check the main, ignition and radiator fan
motor fuses for continuity.
Refer to “CHECKING THE FUSES” in chap-
ter 3.

Are the main, ignition and radiator fan motor
fuses OK?
Replace the fuse(s).
EAS00808
TROUBLESHOOTING

The radiator fan motor fails to turn.

The coolant temperature indicator light
fails to light when the engine is warm.
Check:
1. main, ignition, and radiator fan motor fuses
2. battery
3. main switch
4. radiator fan motor
5. radiator fan motor relay
6. coolant temperature sensor
7. wiring connections
(the entire cooling system)

Before troubleshooting, remove the following
part(s):
1. seat
2. fuel tank
3. side cowlings

Troubleshoot with the following special tool(s).
Pocket tester
90890-03112, YU-3112
EAS00738
ProCarManuals.com