engine YAMAHA YZF-R1SC 2004 Manual PDF

5-10
ENGINEENG
51 Nm (5.1 m
kg, 37 ft
lb)
NOTE:
45 Nm (4.5 m
kg, 33 ft
lb)
45 Nm (4.5 m
kg, 33 ft
lb)
Pivot shaft wrench
90890-01471, YM-01471
Pivot shaft wrench adapter
90890-01476
7. Tighten:

upper self-locking nut
1

lower self-locking nut 2
First tighten the lower self-locking nut, and then
tighten the upper self-locking nut.
8. Tighten:

left front engine mounting bolt
1
9. Tighten:

right front engine mounting bolt
1
ProCarManuals.com

5-18
CAMSHAFTENG
NOTE:
NOTE:
NOTE:
3. Install:

timing chain tensioner spring

timing chain tension rod
1
Prior to installing the timing chain tensioner rod,
drain the engine oil from the timing chain ten-
sioner housing.
a. Install the timing chain tensioner spring and
timing chain tensioner rod
1.
b. Squeeze the timing chain tensioner clip
2
and push the timing chain tensioner rod 3.
When the timing chain tensioner rod
3 is
pushed while holding the grip of the timing chain
tensioner clip
2, make sure not to release the
timing chain tensioner rod
3 before releasing
the timing chain tensioner clip
2. (Otherwise,
the timing chain tensioner rod
3 may run off.)
c. Hook the clip
4 to the timing chain tensioner
rod
3.
Hook the timing chain tensioner rod pin
5 to the
center of the clip
4. After the installation, check
that the clip
4 can come off by its own weight by
pushing the timing chain tensioner rod
3 at the
position of installation.
ProCarManuals.com

5-19
CAMSHAFTENG
NOTE:
NOTE:
NOTE:
EAS00215
INSTALLING THE CAMSHAFTS
1. Align:

“T” mark
a on the pickup rotor
(with the crankcase mating surface
b)
a. Turn the crankshaft clockwise.
b. When piston #1 is at TDC, align the “T” mark
a with the crankcase mating surface b.
2. Install:

intake camshaft sprocket
1

exhaust camshaft sprocket 2
(with the camshaft sprockets temporarily
tightened)
Install the camshaft sprockets as a illustration.
3. Install:

exhaust camshaft
1

intake camshaft 2
(with the camshaft sprockets temporarily
tightened)
Make sure the punch mark
a faces up.
4. Install:

dowel pins

exhaust camshaft caps

intake camshaft caps

Make sure each camshaft cap is installed in its
original place.

Make sure the arrow mark
a on each cam-
shaft cap points towards the right side of the
engine.
L: Left side camshaft cap mark
R: Right side camshaft cap mark
I: Intake side camshaft cap mark
E: Exhaust side camshaft cap mark
ProCarManuals.com

5-20
CAMSHAFTENG
10 Nm (1.0 m
kg, 7.2 ft
lb)
NOTE:
CAUTION:
24 Nm (2.4 m
kg, 17 ft
lb)
CAUTION:
5. Install:

camshaft cap bolts
Tighten the camshaft cap bolts in stages and in
a crisscross pattern, working from the inner
caps out.

Lubricate the camshaft cap bolts with the
engine oil.

The camshaft cap bolts must be tightened
evenly or damage to the cylinder head,
camshaft caps, and camshafts will result.

Do not turn the crankshaft when installing
the camshaft to avoid damage or improper
valve timing.
6. Tighten:

camshaft sprocket bolts
1
Camshaft wrench
90890-04143
Be sure to tighten the camshaft sprocket
bolts to the specified torque to avoid the
possibility of the bolts coming loose and
damaging the engine.
7. Align:

camshaft punch mark
a
Align the camshaft punch mark a and the
camshaft cap arrow mark
b.
Camshaft wrench
90890-04143
ProCarManuals.com

5-22
Order Job / Part Q’ty Remarks
1
2
3
4
5
6Removing the cylinder head
Engine
Intake camshaft
Exhaust camshaft
Cylinder head
Cylinder head gasket
Dowel pin
Coolant pipe
O-ring
Thermo wax out let hose1
1
2
1
1
1Remove the parts in the order listed.
Refer to “ENGINE”.
Refer to “CAMSHAFTS”.
For installation, reverse the removal
procedure.
18 Nm (1.8 m
kg, 13 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
19 Nm (1.9 m
kg, 14 ft
lb)
67 Nm (6.7 m
kg, 48 ft
lb)
1st
2nd
10 Nm (1.0 m
kg, 7.2 ft
lb)
CYLINDER HEADENG
EAS00221
CYLINDER HEAD
ProCarManuals.com

5-24
CYLINDER HEADENG
8 Nm (0.8 m
kg, 5.8 ft
lb)
NOTE:
NOTE:
19 Nm (1.9 m
kg, 14 ft
lb)
67 Nm (6.7 m
kg, 48 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
NOTE:
EAS00233
INSTALLING THE CYLINDER HEAD
1. Check:

cylinder head bolts
1
Retighten the cylinder head bolts to specifica-
tion, before installing the cylinder head.
2. Install:

gasket
New
1

dowel pins
3. Install:

cylinder head
Pass the timing chain through the timing chain
cavity.
4. Tighten:

cylinder head nuts
1
10
1st
2nd

cylinder head bolts
11 12

First, tighten the nuts 1
10 to approximate-
ly 19 Nm (1.9 m
kg, 14 ft
lb) with a torque
wrench, and then tighten the 67 Nm (6.7 m
kg,
48 ft
lb).

Lubricate the cylinder head nuts with engine
oil.

Tighten the cylinder head nuts in the proper
tightening sequence as shown and torque
them in two stages.
5. Install:

exhaust camshaft

intake camshaft
Refer to “INSTALLING THE CAMSHAFTS”.
ProCarManuals.com

5-35
Order Job / Part Q’ty Remarks
1
2
3
4
5
6
7
8
9Removing the stator coil assembly
Rider seat
Fuel tank
Left side cowling
Bottom cowlings
Engine oil
Stator coil assembly lead coupler
Plug
Generator rotor cover
Gasket
Dowel pin
Generator rotor assembly
Dowel pin
Bearing housing
Collar1
1
1
1
2
1
2
1
1Remove the parts in the order listed.
Refer to “SEATS” in chapter 3.
Refer to “FUEL TANK” in chapter 3.
Refer to “COWLINGS” in chapter 3.
Drain.
Refer to “CHANGING THE ENGINE OIL”
in chapter 3.
Disconnect.
10 Nm (1.0 m
kg, 7.2 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
12 Nm (1.2 m
kg, 8.7 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
10 Nm (1.0 m
kg, 7.2 ft
lb)
14 Nm (1.4 m
kg, 10 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
STARTER CLUTCH AND GENERATORENG
STARTER CLUTCH AND GENERATOR
STATOR COIL ASSEMBLY
ProCarManuals.com

5-38
STARTER CLUTCH AND GENERATORENG
NOTE: REMOVING THE GENERATOR
1. Remove:

rider seat

fuel tank
Refer to “SEATS” and “FUEL TANK” in chapter
3.
2. Remove:

left side cowling

bottom cowlings
Refer to “COWLINGS” in chapter 3.
3. Drain:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
4. Remove:

plug

generator rotor cover
1

While pushing generator rotor, remove the
generator rotor cover.

Loosen each bolt 1 / 4 of a turn a time, in stages
and in a crisscross pattern.

After all of the bolts are fully loosened, remove
them.
5. Remove:

generator rotor and starter clutch assembly
1.
6. Remove:

idler gear shaft bolt
1

idler shaft

idler gear
2
ProCarManuals.com

5-41
STARTER CLUTCH AND GENERATORENG
NOTE:
NOTE:
10 Nm (1.0 m
kg, 7.2 ft
lb)
INSTALLING THE STARTER CLUTCH
1. Install:

generator rotor
1

damper 2

driven gear 3

The hole side of the damper is installed to the
generator side.

Lubricate the engine oil
4.
2. Install:

starter clutch drive gear
1

collar 2

washer 3
Refer to “CHECKING THE STARTER
CLUTCH”.
3. Install:

washer
1

O-ring 2 New

spacer
3
Lubricate the engine oil to O-ring.
INSTALLING THE GENERATOR
1. Install:

idle gear shaft

idle gear
1

washer

idle gear shaft bolt
2
LOCTITE
2. Install:

generator rotor and starter clutch assembly
1
ProCarManuals.com

5-42
STARTER CLUTCH AND GENERATORENG
12 Nm (1.2 m
kg, 8.7 ft
lb)
22 Nm (2.2 m
kg, 16 ft
lb)
NOTE: 3. Install:

generator cover gasket

generator cover
1
(M6 bolts)
(M8 bolts)

First tighten the M8 bolts and then tighten the
M6 bolts.

Tighten the generator rotor cover bolts in
stages and in a crisscross pattern.
4. Fill:

engine oil
Refer to “CHANGING THE ENGINE OIL” in
chapter 3.
5. Install:

bottom cowling

left side cowling
Refer to “COWLINGS” in chapter 3.
6. Install:

fuel tank

rider seat
Refer to “SEATS” and “FUEL TANK” in chap-
ter 3.
ProCarManuals.com