sensor YAMAHA YZF-R1SC 2004 Service Manual
Page 12 of 457
STARTER CLUTCH AND GENERATOR5-35 . . . . . . . . . . . . . . . . . . . . . . . . .
STATOR COIL ASSEMBLY 5-35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTER CLUTCH 5-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE GENERATOR 5-38. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE STARTER CLUTCH 5-39. . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE DAMPER 5-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE STARTER CLUTCH 5-40. . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE STARTER CLUTCH 5-41. . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE GENERATOR 5-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CRANKSHAFT POSITION SENSOR5-43 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE CRANKSHAFT POSITION SENSOR 5-44. . . . . . . . .
INSTALLING THE CRANKSHAFT POSITION SENSOR 5-44. . . . . . . .
CLUTCH5-46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH COVER 5-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PULL LEVER SHAFT 5-47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLUTCH 5-48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE CLUTCH 5-50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE FRICTION PLATES 5-52. . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CLUTCH PLATES 5-52. . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CLUTCH SPRINGS 5-53. . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CLUTCH HOUSING 5-53. . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CLUTCH BOSS 5-53. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE PRESSURE PLATE 5-54. . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE PULL LEVER SHAFT AND PULL ROD 5-54. . . . . . .
INSTALLING THE CLUTCH 5-54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHIFT SHAFT5-58 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SHIFT SHAFT AND STOPPER LEVER 5-58. . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE SHIFT SHAFT 5-60. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE SHIFT SHAFT 5-61. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE STOPPER LEVER 5-61. . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE SHIFT SHAFT 5-61. . . . . . . . . . . . . . . . . . . . . . . . . . . .
OIL PAN AND OIL PUMP5-63 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVING THE OIL PAN 5-66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE SPROCKET AND CHAIN 5-66. . . . . . . . . . . . . . . . . . . .
CHECKING THE OIL PUMP 5-67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE RELIEF VALVE 5-67. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE OIL DELIVERY PIPE AND OIL PIPE 5-68. . . . . . . . .
CHECKING THE OIL STRAINER 5-68. . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE OIL NOZZLES 5-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLING THE OIL PUMP 5-68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLING THE OIL / WATER PUMP ASSEMBLY 5-69. . . . . . . . . . . .
INSTALLING THE OIL PAN 5-71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCarManuals.com
Page 14 of 457
CHECKING THE WATER PUMP 6-14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASSEMBLING THE WATER PUMP 6-15. . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 7
FUEL INJECTION SYSTEM
FUEL INJECTION SYSTEM7-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WIRING DIAGRAM 7-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECU’S SELF-DIAGNOSTIC FUNCTION 7-4. . . . . . . . . . . . . . . . . . . . . .
SUBSTITUTE CHARACTERISTICS OPERATION CONTROL
(FAIL-SAFE ACTION) 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FAIL-SAFE ACTIONS TABLE 7-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING CHART 7-7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSTIC MODE 7-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TROUBLESHOOTING DETAILS 7-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THROTTLE BODIES7-35 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INJECTORS 7-37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE INJECTORS 7-39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE THROTTLE BODIES 7-39. . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE THROTTLE BODY JOINTS 7-39. . . . . . . . . . . . . . . . . .
CHECKING THE PRESSURE REGULATOR 7-40. . . . . . . . . . . . . . . . . .
CHECKING THE FUEL PUMP AND PRESSURE REGULATOR
OPERATION 7-40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE THROTTLE POSITION
SENSOR 7-41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE SUB-THROTTLE POSITION
SENSOR 7-43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING AND ADJUSTING THE THERMO WAX 7-45. . . . . . . . . . . .
AIR INDUCTION SYSTEM7-46 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR INJECTION 7-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR CUT-OFF VALVE 7-46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR INDUCTION SYSTEM DIAGRAMS 7-47. . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE AIR INDUCTION SYSTEM 7-48. . . . . . . . . . . . . . . . . .
CHAPTER 8
ELECTRICAL SYSTEM
ELECTRICAL COMPONENTS8-1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING SWITCH CONTINUITY8-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE SWITCHES8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE BULBS AND BULB SOCKETS8-5 . . . . . . . . . . . . . . . . .
TYPES OF BULBS 8-5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECKING THE CONDITION OF THE BULBS 8-5. . . . . . . . . . . . . . . .
ProCarManuals.com
Page 38 of 457
2-10
ENGINE SPECIFICATIONSSPEC
ItemStandardLimit
Transmission
Transmission type
Primary reduction system
Primary reduction ratio
Secondary reduction system
Secondary reduction ratio
Operation
Gear ratios
1st gear
2nd gear
3rd gear
4nd gear
5th gear
6th gear
Max. main axle runout
Max. drive axle runout
Constant mesh, 6-speed
Spur gear
65 / 43 (1.512)
Chain drive
45 / 17 (2.647)
Left-foot operation
38 / 15 (2.533)
33 / 16 (2.063)
37 / 21 (1.762)
35 / 23 (1.522)
30 / 22 (1.364)
33 / 26 (1.269)
0.08 mm
(0.0032 in)
0.08 mm
(0.0032 in)
Shifting mechanism
Shift mechanism type
Max. shift fork guide bar bending
Shift drum / Guide bar
0.10 mm
(0.0039 in)
Air filter typeOil coated paper element
Fuel pump
Pump type
Model (manufacturer)
Output pressure
Electrical
5PW (DENSO)
294 kPa (2.94 kg / cm
2, 2.94 bar, 42.6 psi)
Throttle position sensor
Resistance
Output voltage (at idle)
4.9 5.1 kΩ at 20C (68F)
0.63 0.73 V
Throttle bodies
Model (manufacturer) quantity
Intake vacuum pressure
Throttle cable free play (at the flange
45EIDW (MIKUNI) 2
22 kPa (165 mmHg, 6.4966 inHg)
3 5 mm (0.12 0.20 in)
of the throttle grip)
ID mark
Throttle valve size
5VY1 00 (USA)
5VY5 10 (CAL)
#100
ProCarManuals.com
Page 43 of 457
2-15
ELECTRICAL SPECIFICATIONSSPEC
ELECTRICAL SPECIFICATIONS
ItemStandardLimit
System voltage12 V
Ignition system
Ignition system type
Ignition timing
Crankshaft position sensor
resistance / color
T.C.I. unit model (manufacturer)
DC. T.C.I.
5 BTDC at 1,050 r / min
336 504 Ω at 20C (68F) / Gy-B
F8T822 (MITSUBISHI) (USA)
F8T823 (MITSUBISHI) (CAL)
Ignition coils
Model (manufacturer)
Minimum ignition spark gap
Primary coil resistance
Secondary coil resistance
F6T558 (MITSUBISHI)
6 mm (0.24 in)
1.19 1.61 Ω at 20C (68F)
8.5 11.5 kΩ at 20C (68F)
Charging system
System type
Model (manufacturer)
Normal output
Stator coil resistance / color
A.C. magneto
F4T850 (MITSUBISHI)
14 V / 560 W at 5,000 r / min
0.14 0.18 Ω at 20C (68F) / W-W
Rectifier / regulator
Regulator type
Model (manufacture)
Semi conductor short circuit
FH011AA (SHINDENGEN)
()
No-load regulated voltage
Rectifier capacity
Withstand voltage
()
14.3 15.1 V
50 A
100 V
Battery
Battery type
Battery voltage / capacity
Specific gravity
Manufacturer
Ten hour rate amperage
YTZ10S
12 V / 8.6 Ah
1.310
YUASA
0.8 A
Headlight typeHalogen bulb
Bulbs (voltage / wattage quantity)
Headlight
Auxiliary light
Tail / brake light
Front turn signal light / position light
Rear turn signal light
Licence plate light
Meter light
12 V 55 W 4
12 V 5 W 2
LED 1
12 V 21 W / 5 W 2
12 V 21 W 2
12 V 5 W 1
LED 1
ProCarManuals.com
Page 49 of 457
2-21
TIGHTENING TORQUESSPEC
NOTE 1:
NOTE 2:
ItemFastenerThreadQ’tyTightening torqueRemarksItemFastenersizeQtyNmmkgftlbRemarks
Main axle bearing housingBoltM63121.28.7
Shift fork shaft stopperBoltM62101.07.2
Stopper screwScrewM81222.216
Shift rod lock nut (rear)NutM6170.75.0Left thread
Shift rod lock nut (front)NutM6170.75.0
Shift rod jointBoltM61101.07.2
Shift armBoltM61101.07.2
E.C.U.ScrewM6270.75.0
Neutral switch—M101202.015
EXUP servo motor coverScrewM5220.21.5
Coolant temperature sensor—M121181.813
Cylinder identification sensorBoltM6180.85.7
Atmospheric pressure sensorScrewM5270.75.0
Crankshaft position sensorBoltM61101.07.2
Oil level switchBoltM62101.07.2
1. First, tighten the bolts to approximately 19 Nm (1.9 mkg, 14 ftlb) with a torque wrench following the
tightening order.
2. Retighten the bolts 67 Nm (6.7 mkg, 48 ftlb) with a torque wrench.
1. First, tighten the bolts to approximately 20 Nm (2.0 mkg, 15 ftlb) with a torque wrench following the
tightening order.
2. Loosen the all bolts one by one following the tightening order and then tighten them to 20 Nm (2.7
mkg, 15 ftlb) again.
3. Retighten the bolts further to reach the specified angle (60).
ProCarManuals.com
Page 52 of 457
2-24
TIGHTENING TORQUESSPEC
NOTE 1:
NOTE 2:
NOTE 3:
ItemThreadTighteningRemarksItemsizeNmmkgftlbRemarks
Battery box and frameM670.75.1
Atmospheric pressure sensor and battery box—0.70.070.5
Lean angle cut-off switch and battery box—20.21.4
Foot rest bracket (front) and frameM8282.820
Foot rest bracket (rear) and frameM8282.820
Rear brake master cylinder and foot rest bracketM6181.813
Rear brake hose union boltM10303.022
Sidestand bracket and frameM10636.346
Front wheel axle shaft and boltM14919.166
Rear wheel axle nutM2415015.0109
Front brake caliper and front forkM10353.525
Front brake disc and front wheelM6181.813
Rear brake disc and rear wheelM6303.022
Rear wheel sprocket and drive hubM1010010.072
Brake caliper bleed screwM860.64.3
Front wheel axle pinch boltM8202.014See NOTE 3
1. First, tighten the ring nut to approximately 52 Nm (5.2 mkg, 38 ftlb) with a torque wrench, then
loosen the ring nut completely.
2. Retighten the lower ring nut to specification.
Refer to “INSTALLING THE ENGINE” in chapter 5.
1. Insert the front wheel axle from the right side
and tighten it with the flange bolt from the left
side to 91 Nm (9.1 mkg, 65.8 ftlb).
2. In the order from the pinch bolt
2 pinch
bolt
1 pinch bolt 2, tighten each bolt to
20 Nm (2.0 mkg, 14 ftlb) without perform-
ing temporary tightening.
3. Check that the end face of the axle head and
the end face of the fork side are flush-
mounted. If they are out of alignment, make
sure to fit them by adding the external force
by hand or with a plastic hammer, etc.
If the end face of the axle is not parallel to the
end face of the fork, align them so that one
point of the axle circumference is positioned
on the end face of the fork.
At this stage, it can be accepted if the end
face of the axle becomes partially concave
to the end face of the fork.
4. In the order from the pinch bolt
4 pinch
bolt
3 pinch bolt 4, tighten each bolt to
20 Nm (2.0 mkg, 14 ftlb) without perform-
ing temporary tightening.
ProCarManuals.com
Page 67 of 457
2-39
E Clamp the clamp upper end
along the line of lower end of the
hose clamp assembly. Point the
tip of the clamp (surplus section)
to the front side of the vehicle.
Clutch cable is what the clamp
fastens.
F The clutch cable doesn’t project
outside the water hose and the
cylinder head in the box part in
the figure.
G To the engine
H Clamp behind the bracket 3.17Throttle body lead
A Clamp it after passing between
the frame and radiator stay.
Point the tip of the clamp (exces-
sive part) to the front side of the
vehicle. Fasten the right handle-
bar switch lead with a clamp.
B To the wire harness
C The clutch cable positioning
guide should be above the upper
end of the clamp. Fasten the
clutch cable with a clamp. (Refer
to )
D Position relation between the
clamp and guide.
M
CABLE ROUTINGSPEC
1Wire harness
2Crankshaft position sensor lead
3Heat protector
4Right handlebar switch lead
5Positioning guide
6Rear brake light switch lead
7Coolant reservoir tank
8Speed sensor lead
9Clutch cable
10Radiator
11Oil cooler outlet hose
12Coolant reservoir tank drain
hose
13Breather pipe
14Fuel tank drain hose
15A.C. magneto lead
16Wire harness
ProCarManuals.com
Page 68 of 457
2-40
P To the air filter
Q Route the fuel tank drain hose
over the canister stay and be-
tween the breather hose 2 and
wire harness. On the front side of
the canister stay, let though the
bottom of the A.C.magneto lead
and the wire harness.
R Route by the upside of vehicle
away from the canister stay.
CABLE ROUTINGSPEC
I The coupler for the air induction
solenoid lead and camshaft sen-
sor lead should be connected
above the ignition coil sub wire
harness and it should not drop
on the cylinder head cover be-
hind the ignition coil.
J Pass the right handlebar switch
lead between the frame and heat
protector.
K Coolant reservoir tank drain
hose should cross with the
speed sensor lead under the
swingarm bracket. Route the
coolant reservoir tank drain hose
over the up side of the vehicle.L Pass the rear brake light switch
lead between the swingarm
bracket and coolant reservoir
tank.
M Release the tip of the clamp and
install it to the clutch cable.
Insert the clamp to the hole lo-
cated on the right back side of
the radiator.
Radiator fan motor lead should
not be caught while inserting the
clamp.
N Push the clamp until it hits the ra-
diator side stay. Radiator fan mo-
tor lead should not be caught.
O Clamp the clutch cable so that it
is within this specified clamp.
ProCarManuals.com
Page 71 of 457
2-43
33Throttle body side cap
34Mud guard
35Turn signal light lead
36License plate light lead
37Rear fender rib
38Speed sensor lead
39Rear brake light switch lead
40Rear frame
41Swingarm bracket
42Main fuse lead
43Starting circuit cut-off relay lead
44Turn signal light relay lead
45Starter relay lead
46Main fuse lead (To the battery
positive lead)
47Right handlebar switch lead
17Battery negative lead
18Starter motor lead
19A.C.magneto lead
20Oil level switch lead
21Sidestand switch lead
22Throttle body lead
23Coolant reservoir tank drain hose
24Fuel tank drain hose
25Cover 7
26Radiator fan motor lead (left)
27Radiator fan motor lead (right)
28Wire harness
29Pipe 3
30Frame
31Coolant reservoir tank hose
32Thermo stat assembly breather
hose
CABLE ROUTINGSPEC
1Heat protector
2Crankshaft position sensor lead
3Neutral switch lead
4Ground lead
5Coolant reservoir tank
6Battery positive lead
7Starter relay
8Turn signal relay
9Main fuse
10Lean angle cut-off switch
11Atmospheric pressure sensor
12Tail / brake light lead
13Rear fender
14Seat lock cable
15Anti safety alarm coupler
16Starting circuit cut-off relay
ProCarManuals.com
Page 72 of 457
2-44
K Pass the water hose lower side
of the thermostat, and between
the ground lead and the neutral
switch.
L Install the leads so that the en-
gine ground lead is positioned
lower and the battery negative
lead to be upper. Install the pro-
trusion of each lead to be above
the vehicle.
M Route the crankshaft position
sensor lead under the wire har-
ness.
N To the fuel pump
O Clamp the wire harness winding
in and insert it to the frame hole.A Pass the wire harness through
the clamp inserted to the radiator
stay.
B To the headlight lead
C Clamp the lead between three
protrusions of the pipe (the first
and second parts from the ve-
hicle front). Point the tip of the
clamp (excessive part) to the in-
side of the vehicle.
D To the vehicle right side diagram
E To the engine
F Clamp the lead between three
protrusions of the pipe (the in-
side and outside of the vehicle).G Point the tip of the clamp (exces-
sive part) to the inside of the ve-
hicle.
H All hoses and leads should be
routed over the vehicle’s upper
side above the heat protector.
I To the starter motor
J Fasten the wire harness, clank
shaft position sensor lead, rear
brake light switch lead and
speed sensor lead with a clamp.
Then, point the tip of the clamp
(cut the tip of the clamp leaving 2
to 4 mm (0.08 to 0.16 in).) to the
inside of the vehicle.
CABLE ROUTINGSPEC
ProCarManuals.com