brake pads ARIEL ATOM 2 2006 Owners Manual
[x] Cancel search | Manufacturer: ARIEL, Model Year: 2006, Model line: ATOM 2, Model: ARIEL ATOM 2 2006Pages: 79, PDF Size: 2.5 MB
Page 22 of 79
16
BRAKE PACKAGES
Your Atom is equipped with one of the following bra ke packages:
Base Floating calipers front & rear with 10.3 in. front v entilated rotor and 10.3 in. rear ventilated rotor.
Sport Wilwood Dynalite 4 piston caliper front and floating PBR caliper rear, with 10.3 in. front
ventilated rotor and 10.3 in. rear ventilated rotor .
Track Wilwood Dynalite 4 piston caliper front & rear calipe r and parking brake caliper with 11 in. front
two-piece ventilated rotor and 11 in. two-piece venti lated rotor.
Race Alcon 4 piston caliper front & rear with 11 in. front two-piece slotted & ventilated rotor, and 11 in.
rear two-piece slotted & ventilated rotor.
Brake pads should be inspected before every track event to ensure that there has been no pad damage,
thickness issues, or deterioration.
The brake rotors should be replaced when their thickn ess decreases to 19mm, when pulsation is noted, or
if cracking or other physical damage is found during in spection. Additionally, the brake pads should be
replaced when replacing the rotors.
Check brake fluid levels often. Some decrease is to be expected as the pads wear. Additionally, the brake
lines should be checked for rubbing or scraping.
Page 60 of 79
54
MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2
SCHEDULE I: GENERAL REFERENCE
Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Replace every 30,0 00 miles (48,000 km). Supercharger
Aftercooler Coolant Check before every track event. Replace every 30,0
00 miles (48,000 km). Air Filter Check before every track event. Clean and oil ever
y 5,000 miles (8,000 km). The Filtercharger®
element must be cleaned and serviced with K&N clean er and air filter oil per the prescribed routine
maintenance procedures as outlined in the product l iterature that accompanies the Filtercharger®. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event; change every 10,000 miles (16,000 km). Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Replace when thickness decreases to 19mm, when puls
ation is noted, or if cracking or other physical
damage is found during inspection. Refer to the br ake bedding procedures on page12. Brake Pads Inspect for pad damage, thickness issues or deterio
ration before every event. Replace brake pads
when brake rotors are replaced. Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System Use a wrench to inspect flange bolts for tightness
every 5,000 miles (8,000 km), check gaskets at
this time. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels Check wheel nut torque after the first 50 miles (80
km) of operation and before every track event
thereafter. Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check belt for cracking or abnormal wear every 3,00 0 miles (4,800 km). Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.
Page 61 of 79
55
MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2
SCHEDULE II: BEFORE EVERY TRACK EVENT
Component Service/Operation
Engine Oil
Check before every track event. Change as necessar y. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every track event. Supercharger
Aftercooler Coolant Check before every track event.
Air Filter
Check before every track event. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Inspect for leaks before every track event. Brake Fluid
Inspect levels, condition, and any leakage before e very track event. Brake Rotors Refer to the Brake Bedding Procedures on page12. I
nspect and replace when thickness decreases
to 19mm, when pulsation is noted, or if cracking or other physical damage is found during inspection.
Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Refer to the brake bedding procedure s on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect lines for rubbing or scraping before every
track event. Exhaust System
Visually inspect exhaust flange bolts for tightness and/or damage. Tires
Inspect tires for proper pressure and tread wear be fore and after every track event. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends.
Page 62 of 79
56
MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2
SCHEDULE III: INITIAL 50 MILES (80 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Oil Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
No service required. Transmission Fluid
No service required. Brake Fluid
Check level. Fill as necessary. Brake Rotors
Refer to the brake bedding procedures on page12. Brake Pads
Refer to the brake bedding procedures on page12. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.
Page 63 of 79
57
MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2
SCHEDULE IV: INITIAL 300 MILES (480 KM)
Component Service/Operation
Engine Oil
Check and fill as necessary. Engine Filter
No service required. Engine Coolant
Check and fill as necessary. Supercharger
Aftercooler Coolant Check and fill as necessary.
Air Filter
No service required. Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
No service required. Brake Fluid
Check level; fill as required. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage, check gaskets visually to ensure
they have not developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.
Page 64 of 79
58
MAINTENANCE SCHEDULE FOR THE ARIEL ATOM 2
SCHEDULE V: EVERY 1000 MILES (1600 KM)
Component Service/Operation
Engine Oil
Check before every track event or every 1,000 miles (1,600 km). Change as necessary. Engine Oil Filter
Replace during every oil change. Engine Coolant
Check before every event. Replace every 30,000 mil es (48,000 km). Supercharger
Aftercooler Coolant Check before every event. Replace every 30,000 mil
es (48,000 km). Air Filter
Clean and oil every 5,000 miles (8,000 km) Spark Plugs
Inspect before every track event and change if nece ssary. Transmission Fluid
Change every 10,000 miles (16,000 km). Brake Fluid
Check level. Fill as needed. Brake Rotors Inspect and replace when thickness decreases to 19m
m, when pulsation is noted, or if cracking or
other physical damage is found during inspection. Brake Pads Inspect for pad damage, thickness issues or deterio
ration. Replace brake pads when brake rotors
are replaced. Brake Hoses &
Lines Inspect brake lines for rubbing, scraping, or any d
amage. Fuel Lines &
Connections Inspect for damage.
Exhaust System Visually inspect exhaust flange bolts for tightness
and/or damage. Use a wrench to inspect flange
bolts for tightness every 5,000 miles (8,000 km), c heck gaskets visually to ensure they have not
developed a leak. Tires
Inspect for any unusual tread wear. Wheels
Ensure lug nut torque is 80 ft-lbs. Drive Belt
Check for abnormal wear. Rod Ends Inspect rods ends on Push Rods, Steering Rods, and
A-Arms for any signs of fatiguing or wear,
replace if parts appear worn. Verify that all chec k nuts are tight on all rod ends. We recommend
replacement of all suspension rod ends at 3000mi or sooner based upon driving habits.
Page 69 of 79
63
BRAKE PAD OPTIONS
Base Brake Package Parts
PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
PBR 54mm floating front
caliper (left) AA-BK-002 PBR
BCB843199PL
1 PBR 54mm floating front
caliper (right) AA-BK-003 PBR
BCB843200PL 1 PBR 40.5mm floating
rear caliper w/ e-brake (left) AA-BK-004
PBR
BCB821020PL 1 PBR 40.5mm floating
rear caliper w/ e-brake (right) AA-BK-005
PBR
BCB821019PL 1 Single piece ventilated 10.3 rotor (262 x 21mm)
AA-BK-006
Galfer SKU#A24255VF
4
Front pads AA-BK-008 PBR
SS-7662X 1
Organic rear brake pads
for 1993-1997 Chevrolet
Camaro AA-BK-055
NAPA
SS-7301-M 1
Page 70 of 79
64
Sport Brake Package Parts
PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
Wilwood 4 x 35.1mm
Dynalite caliper (L & R) AA-BK-010 Wilwood
120-6806-R/L 2 PBR 40.5mm floating
rear caliper/parking brake (left) AA-BK-004
PBR
BCB821020PL 1 PBR 40.5mm floating
rear caliper/parking brake (right) AA-BK-005
PBR
BCB821019PL 1 Single piece ventilated
10.3 front rotor (262 x 21mm) AA-BK-006
Galfer
SKU#A24255VF 4 Front pads-Type 7112 Q
(street compound-4
pads)
AA-BK-015
Wilwood 15Q-6824K
1
Organic rear brake pads
for 1993-1997 Chevrolet
Camaro AA-BK-055
NAPA
SS-7301-M 1
Page 71 of 79
65
Track Brake Package Parts
PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
Mr. Parker parking brake
caliper AA-BK-019 Revolution Brake
Mr. Parker 2 Mr. Parker parking brake
pads (4 pads) AA-BK-035 Wilwood
150-8937K/6823K 1
Aluminum Rotor Hat
Front and Rear AA-UP-044-1 4 Wilwood 4x 35.1mm
Dynalite caliper (L & R) AA-BK-010 Wilwood
120-6806-R/L 4 Wilwood two-piece vented & slotted rotor (right) 279.4x20.6mm
AA-BK-054
Wilwood 160-5840-SR
2
Wilwood two-piece
vented & slotted rotor, left (279.4 x 20.6mm) AA-BK-057
Wilwood
160-5840-SL 2
Pads, Type 7112 BP-20
(medium-high
compound-4 pads) AA-BK-056
Wilwood
150-9413K 2
Page 72 of 79
66
Race Brake Package Parts
PART
DESCRIPTION BRAMMO PART
# MANUFACTURER AND
MFR. PART # QTY.
Alcon 4x34.9 mm fixed
racing caliper (left) AA-BK-036 Alcon
CAR3653D01ASLL 2 Alcon 4x34.9 fixed
racing caliper (right) AA-BK-026 Alcon
CAR3653D01ASRL 2
Mr. Parker parking brake
caliper AA-BK-019 Revolution Brake
Mr. Parker 2 Front pads set (4 pads)
AA-BK-033
Alcon PNP4436X502.4
2
Mr. Parker brake pads (4
pads) AA-BK-035 Wilwood
150-8937K
1 Front Aluminum Rotor
Hat AA-UP-044-1 2 Rear Aluminum Rotor
Hat AA-UP-060 2 Wilwood two-piece
vented & slotted rotor,
right (279.4 x 20.6mm) AA-BK-054
Wilwood
160-5840-SR 2 Wilwood two-piece
vented & slotted rotor, left (279.4 x 20.6mm) AA-BK-057
Wilwood
160-5840-SL 2