engine ASTON MARTIN V8 VANTAGE 2010 Manual Online

Cooling System (03.03)
Engine (03.00)3-3-4 Workshop Manual Issue 5, Janauary 2010
3. Remove throttle body duct for access. (clips x3).
4. Remove pump pulley bolts (x 3) (refer to Figure 1).
Figure 1
5. Release tensioner and slip belt from idler.
6. Remove pump pulley.
Installation
1. Fit pulley to pump with bolts.
2. Torque pulley bolts (bolt x3).
3. Release tensioner and slip belt on idler.
4. Install throttle body duct.
5. Connect breather pipe quickf its (x2) to air cleaner duct.
6. Battery isolation switch ‘ON’.
Oil Temperature Controller - Renew
Remove
1. Raise vehicle on ramp.
2. Remove undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew). 3. Remove pipes from oil thermostat (position container to
catch oil) (refer to Figure 1).
Figure 1
4. Remove controller fr om body (bolts x2).
Install
1. Install controller to body (bolts x2) (torque).
2. Install pipes to oil thermost at (torque) ensure correct
alignment in oil tank bracket.
3. Install undertray (refer to Workshop Manual procedure 01.02.NB Undertray - Front - Renew).
4. Fill tank with approximatel y amount of displaced oil and
replace cap.
5. Use handbook procedure to check oil level.
6. Lower vehicle on ramp.
Radiator Fan and Motor Assembly -
Remove and Install
Removal
1. Open the boot..
2. Set the battery isolation switch to off.
3. Remove the radiator closing panel. (01.02.AA - Radiator Closing Panel).
4. Disconnect the two electrical connectors from the wiring harness for the radiator fan and motor assembly.
5. Remove the two bolts that attach the horn mount bracket to the body.
6. Move the horn assembly away.
7. Remove the two nuts that attach the radiator fan and motor assembly to the body.
8. Remove the radiator fan and motor assembly.
Installation
1. Install the radiator fan and motor assembly.
2. Install and tighten the two nuts that attach the radiator fan and motor assembly to the body.
Repair Operation Time (ROT)
A030350
Repair Operation Time (ROT)
ItemCode
Radiator Fan and Motor Assembly -
Remove and Install 03.03.DB
A030242

Cooling System (03.03)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-3-5
3. Put the horn assembly into the correct position.
4. Install and tighten the two bolts that attach the horn mount bracket to the body.
5. Connect the two electrical connectors to the wiring harness for the radiator fan and motor assembly.
6. Install the radiator closin g panel. (0102AA - Radiator
Closing Panel).
7. Set the battery isolation switch to on.
8. Close the boot.
Radiator and Condenser Assembly -
Renew
Removal
1. Remove cooling fan pack (refer to Workshop Manual procedure 03.03.DB Fan and Motor Assembly -
Radiator - Renew).
2. Remove grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
3. Drain cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
4. Recover refrigerant (refer to Workshop Manual procedure 12.03.FA Refrigerant Gas - Recover/Recharge
- Renew).
5. Remove bolts (x4), that attach the PAS fluid cooler to bonnet latch cross member. Tie fluid cooler aside.
6. Remove bolts (x6), and spacers (x2) that attach the bonnet latch cross member to body and position aside.
7. Disconnect top and bottom hose from radiator (clips
x2).
8. Remove expansion tank hose from radiator (clip x1).
9. Remove bolts (x2), that attach the condenser pipe connections. Plug pipes and block connections.
10. Remove radiator mounting rubbers (x4)
11. Remove foam seals from radiator (x3).
Installation
1. Install foam seals to radiator (x3).
2. Install rubber mounts to radiator (x4).
3. Clean pipe connections, remove plugs.
4. Install new 'O' rings to pipe connections. Connect pipes to condenser. Install and torque tighten bolts (x2).
5. Connect top and bottom hoses to radiator (clips x2).
6. Connect expansion tank hose to radiator (clip x1). 7. Install bonnet latch cross member, install spacers and
bolts (torque).
8. Position PAS fluid cooler to cross member, install and
torque tighten bolts (x4).
9. Install grill (refer to Workshop Manual procedure
01.08.AA Grille - Radiator - Renew).
10. Install cooling fan pack (refer to Workshop Manual procedure 03.03.DB Fan and Motor Assembly -
Radiator - Renew).
11. Recharge refrigerant (refer to Workshop Manual procedure 12.03.FA Refriger ant Gas - Recover/Recharge
- Renew).
12. Refill cooling system (r efer to Workshop Manual
procedure 03.03.AD Coolant - Drain and Refill).
Radiator Assembly - Renew
Removal
1. Remove cooling fan pack (refer to Workshop Manual procedure 03.03.EB Fan and Motor Assembly Radiator -
Renew
2. Remove grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
3. Drain coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
4. Remove bolt that attaches the PAS pipe bracket to bottom cross member.
5. Remove bolts (x6), and spacers (x2) that attach the bonnet latch cross member to body and position aside.
6. Disconnect top and bottom hose from radiator (clips x2).
7. Disconnect top and bottom hose from radiator (clips x2).
8. Remove expansion tank hos e from radiator (clip x1).
9. Remove bolts (x2) that attach the radiator to condenser.
10. Unclip condenser from ra diator and remove from
vehicle (lugs x4) (support condenser).
11. Remove radiator mounting rubbers (x4)
1. Remove foam seals from radiator (x3).
Installation
1. Install foam seals to radiator (x3).
2. Install rubber mounts to radiator (x4).
3. Install radiator and clip to condenser (lugs x4).
4. Install condenser to radiator bolts x2 (torque).
5. Connect top and bottom hoses to radiator (clips x2).
6. Connect expansion tank hose to radiator (clip x1).
7. Install bonnet latch cross member, install spacers and bolts (torque).
8. Position PAS fluid cooler to cross member, install and
torque tighten bolts (x4).
Repair Operation Time (ROT)
Repair Operation Time (ROT)

Cooling System (03.03)
Engine (03.00)3-3-6 Workshop Manual Issue 5, Janauary 2010
9. Install grill (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
10. Install cooling fan pack (refer to Workshop Manual procedure 03.03.EB Fan and Motor Assembly Radiator -
Renew).
11. Raise vehicle
12. Install bottom radiator cros smember (bolts x4) (torque).
13. Install PAS pipe bracket to cross member (bolt x1).
14. Refill coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
Air Conditioning Condenser - Renew
Removal
1. Recover refrigerant gas fr om A/C system (refer to
Workshop Manual procedure 12.03.FA Refrigerant Gas
- Recover/Recharge - Renew).
2. Remove grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew).
3. Remove slam panel (screws x12).
4. Remove bolts (x4), that attach the PAS fluid cooler to bonnet latch cross member. Tie fluid cooler aside.
5. Remove bolts (x6), and spacers (x2) that attach the bonnet latch cross member to body and position aside.
6. Remove bolts (x2), that attach the condenser pipe connections. Plug pipes and block connections.
7. Remove and discard O-rings (x2) from pipe connections.
8. Remove bolts (x2), that attach the condenser to radiator, remove condenser.
Installation
1. Install condenser to radiator, install and torque tighten bolts (x2).
2. Clean pipe connections, remove plugs.
3. Install new O-rings to pipe connections. Connect pipes
to condenser. Install and torque tighten bolts (x2).
4. Install bonnet latch cross member, install spacers and bolts (torque).
5. Position PAS fluid cooler to cross member, install and torque tighten bolts (x4).
6. Install slam panel.
7. Install grille (refer to Workshop Manual procedure 01.08.AA Grille - Radiator - Renew). 8. Refrigerant gas re-charge A/C system (refer to Workshop
Manual procedure 12.03.FA Refrigerant Gas - Recover/
Recharge - Renew).
Radiator Fan Modulator - Remove and
Install
Removal
1. Remove the radiator fan and motor assembly. (0303DB - Radiator Fan and Motor Assembly).
2. Disconnect the two electrical connectors from the radiator fan modulator.
3. Release the five fir tree cl ips that attach the wiring
harness for the radiator fan modulator to the fan cowl.
4. Release the two electrical connectors for the radiator fan modulator from the mount.
5. Remove the screw that attaches the radiator fan modulator to the fan cowl.
6. Remove the radiator fan modulator.
Install
1. Install the radiator fan modulator.
2. Install and tighten the screw that attaches the radiator fan modulator to the fan cowl.
3. Attach the two electrical connectors for the radiator fan modulator to the mount.
4. Install the five fir tree clips that attach the wiring harness for the radiator fan modulator to the fan cowl.
5. Connect the two electrical connectors to the radiator fan modulator.
6. Install the radiator fan and motor assembly. (03.03.DB - Radiator Fan and Motor Assembly).
Expansion Tank Assembly - Renew
Remove
1. Using a syringe, remove coolant from expansion tank.
2. Remove bolts (x4), remove LH corner cross brace.
3. Release clips, disconnect coolant hoses (x3) from expansion tank.
4. Remove upper bolt and side nut that attaches the expansion tank.
Repair Operation Time (ROT)
Repair Operation Time (ROT)
ItemCode
Radiator Fan Modulator - Remove and
Install 03.03.EC
Repair Operation Time (ROT)
ItemCode
Expansion Tank Assembly - Renew 03.03.FB
WAR NI NG
DO NOT REMOVE THE PRESSURE CAP WHEN THE
COOLANT IS HOT. ALLOW TIME FOR THE COOLANT /
ENGINE TO COOL. TAKE PARTICULAR CARE TO AVOID BURNS FROM THE COOLING SYSTEM.

Cooling System (03.03)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-3-7
5. Raise expansion tank sufficient to disconnect multiplug, release clip, disconnect hose.
6. Remove expansion tank.
Install
1. Position expansion tank, connect multiplug , install hose and secure with clip.
2. Install nut and bolt, tighten to correct torque.
3. Install hoses (x3) on expansion tank, secure with clips (x3).
4. Install LH cross brace, inst all bolts (x4) (torque with
vehicle on level ground).
5. Refill expansion tank to correct level with correct
coolant fluid mixture.
6. Clean up any spilled coolant fluid.
Coolant Recovery Tank Assembly -
Remove and Install
Remove
1. Raise the vehicle and make it safe.
2. On Roadster vehicles, re move the centre undertray.
3. Remove the left side front wheel.
4. Remove the five or six M6 Torx-head screws that attach the rear of the wheelarch liner.
5. Remove the self-tapping screw that attaches the rear of the wheelarch liner into the wheelarch.
6. Turn the steering fully to the left.
7. Move the rear of the wheela rch liner away to get access
to the recovery tank. 8. Release the clip that attaches each of the two hoses (2)
to the recovery tank and release the hoses (refer to
Figure 1).
Figure 1
9. Remove the two M6 screws (3) that attach the recovery tank to the body and remove the recovery tank.
Install
1. Put the recovery tank in position on the body.
2. Install and tighten the two M6 attachment screws (3).
3. Connect the two hoses (2) to the recovery tank.
4. Put the clip back in position on each hose.
5. Put the wheelarch liner back into position.
6. Turn the steering to the centre position.
7. Install the self-tapping screw that attaches the rear of the wheelarch liner into the wheelarch.
8. Install the five or six M6 Torx-head screws that attach the rear of the wheelarch liner.
9. Install the front left roadwheel.
10. On Roadster vehicles, install the centre undertray.
11. Lower the vehicle.
12. Do a check of the coolant level and fill if necessary.
Repair Operation Time (ROT)

Cooling System (03.03)
Engine (03.00)3-3-8 Workshop Manual Issue 5, Janauary 2010
Engine Coolant Reservoir Hose - Renew
Removal
1. Drain cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
2. Remove screw and nut that attaches the expansion tank to body, move expansion tank aside (to access hose
clip).
3. Release clip and disconnect hose from expansion tank.
4. Remove hose from engine (quickfit).
5. Release hose from body clip, remove hose.
Installation
1. Install hose, secure in body clip.
2. Install hose to expansion tank, secure with clip.
3. Install and secure hose to engine (quick fit).
4. Install and torque tighten screw and nut that attaches the expansion tank to body.
5. Refill cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
Water Inlet/Outlet Manifold - Renew
Removal
1. Remove reservoir bracket assembly - vacuum system (refer to Workshop Manual procedure 03.08.AE
Reservoir and Bracket Assembly - Vacuum System -
Renew).
2. Disconnect bottom hose (cli p x1) (refer to Figure 1).
Figure 1
3. Disconnect top hose (clip x1) (refer to Figure 2).
Figure 2
Repair Operation Time (ROT)Repair Operation Time (ROT)
ItemCode
Water Inlet/Outlet Manifold - Renew LHD03.03.MH
Water Inlet/Outlet Manifold - Renew RHD03.03.MJ
A030361
A030361A

Cooling System (03.03)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-3-9
4. Disconnect expansion tank feed hose (quickfit) (refer to Figure 3).
Figure 3
5. Disconnect heater feed hose (clip x1) (refer to Figure 4).
Figure 4
6. Disconnect heater return hose (clip x1) (refer to Figure 5).
Figure 5
7. Disconnect breather hose (qui ckfit) (refer to Figure 6).
Figure 6
8. Disconnect separator hose (clip x1) (refer to Figure 7).
Figure 7
9. Disconnect coolant temperature multiplug (refer to
Figure 8).
Figure 8
10. Remove harness clips (x2).
11. Remove 4th bolt of vacuum tank bracket fixing (refer to Figure 9).
A030361B
A030364
A030364A
A030359
A030361
A030373

Cooling System (03.03)
Engine (03.00)3-3-10 Workshop Manual Issue 5, Janauary 2010
12. Remove coolant manifold (bolts x4) (refer to Figure 9).
Figure 9
13. Remove old seals.
14. Remove bracket breather (bolt x1, nut x2).
Installation
1. Install bracket breather (bolt x1, nuts x2) (torque).
2. Clean gasket faces.
3. Install new seals.
4. Install coolant manifold (bolts x4) (torque).
5. Install 4th bolt of vacuum tank bracket fixing (torque).
6. Install harness clips (x2).
7. Connect coolant temp multiplug.
8. Connect separator hose (clip x1).
9. Connect breather hose (quickfit).
10. Connect heater return hose (clip x1).
11. Connect heater feed hose (clip x1).
12. Connect expansion tank feed hose (quickfit).
13. Disconnect top hose (clip x1).
14. Connect bottom hose (clip x1).
15. Install reservoir bracket asse mbly - vacuum system (refer
to Workshop Manual procedu re 03.08.AE Reservoir and
Bracket Assembly - Vacuum System - Renew).
Engine Electric Co olant Temperature
Sensor - Renew
Removal
1. Drain Cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
2. Disconnect breather pipe qu ickfits (x2) from air cleaner
duct.
3. Remove throttle body duct for access. (clips x3). 4. Remove pump pulley bolts (x3) (refer to Figure 1).
Figure 1
5. Release tensioner and slip belt from idler (refer to Figure
2).
Figure 2
6. Remove pump pulley.
7. Disconnect throttle body coolant hose (refer to Figure 3).
Figure 3
Repair Operation Time (ROT)
A030368A030350
A030553
A030364

Cooling System (03.03)
Engine (03.00)
Issue 5, Janauary 2010 Workshop Manual 3-3-11
8. Remove sensor attachment clip (refer to Figure 4).
Figure 4
9. Remove sensor from housing with multiplug, then disconnect (refer to Figure 5)
.
Figure 5
Installation
1. Clean seal area.
2. Install sensor, with multiplug connected.
3. Install sensor attachment clip.
4. Connect throttle body coolant hose.
5. Fit pulley to pump with bolts.
6. Release tensioner and slip belt on idler.
7. Torque pulley bolts (bolt x3).
8. Install throttle body duct.
9. Connect breather pipe quickf its (x2) to air cleaner duct.
10. Refill cooling system (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
Thermostat Cover - Renew
Removal
1. Drain Coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
2. Release breather valve (bolt x1) and tie aside.
3. Disconnect breather pipe qu ickfits (x2) from air cleaner
duct.
4. Remove throttle body duct for access. (clips x3).
5. Unclip engine harness for access (x4).
6. Remove one end of engine breather hoses for access (x3).
7. Remove breather valve bracket for access (nuts x2 bolt x1).
8. Remove thermostat housing from manifold (bolt x3).
9. Remove thermostat and sealing ring.
Installation
1. Install thermostat and sealing ring .
2. Install thermostat housing (torque).
3. Install breather valve bracket.
4. Install breather hoses (x3) and clip.
5. Clip engine harness.
6. Install breather valve.
7. Install throttle body duct.
8. Connect breather pipe quickf its (x2) to air cleaner duct.
9. Refill coolant (refer to Workshop Manual procedure 03.03.AD Coolant - Drain and Refill).
A030389
A030390
Repair Operation Time (ROT)

Cooling System (03.03)
Engine (03.00)3-3-12 Workshop Manual Issue 5, Janauary 2010

Fuel Charging System (03.04)
Engine (03.00)
May 2007 Workshop Manual 3-4-1
Engine (03.00)
Fuel Charging System (03.04)
Safety Precautions
Operations on fuel system result in fuel liquid and vapour
being present in the working environment. This presents a
very serious risk and the following precautions must be
strictly observed:
WAR NI NG
OPERATIONS ON REFUELLING AND THE FUEL
SYSTEM MUST ONLY BE PERFORMED BY PERSONNEL WHO HAVE COMPLETED TRAINING ON FUEL HANDLING.
WAR NI NG
SMOKING MUST NOT BE ALLOWED NEAR THE
WORKING AREA. “NO SMOKING” SIGNS MUST BE POSTED AROUND THE WORKING AREA.
WAR NI NG
ANY OPERATION WHICH COULD INVOLVE SPARKS OR NAKED LIGHTS (E.G. BATTERY TESTING,
WELDING, METAL GRINDING, ETC.) MUST NOT BE ALLOWED NEAR THE WORKING AREA.
WAR NI NG
A CO2 FIRE EXTINGUISHER MUST BE AVAILABLE CLOSE AT HAND.
WAR NI NG
DRY SAND MUST BE AVAILABLE CLOSE AT HAND TO SOAK UP ANY ACCIDENTAL FUEL SPILLAGE.
WAR NI NG
IF NECESSARY, EMPTY THE FUEL INTO AN
EXPLOSION PROOF CONTAINER USING SUITABLE
FIREPROOF FUEL HANDLING EQUIPMENT.
WAR NI NG
THE WORKING AREA MUST BE WELL VENTILATED.
WAR NI NG
DISCONNECT THE BATTERY BEFORE COMMENCING WORK ON THE FUEL SYSTEM.
WAR NI NG
DEPRESSURISE THE FUEL SYSTEM BEFORE DISCONNECTING ANY FUEL LINES.