torque AUDI A3 1996 8L / 1.G AEB ATW Engines Sealing Flanges And Flywheel Driveplate Workshop Manual

13-37


5 -
Gasket
Always replace
6 -
Cylinder block Crankshaft, removing and installing
Page 13
-46

Pistons and connecting rods,
disassembling and assembling Page 13
-
53

7 -
Mounting bolt for dual-mass
flywheel/drive plate
Always replaceTightening torque for dual-mass flywheel:
60 Nm (44 ft lb) + additional 1/2 turn (180
) Tightening torque for drive plate (vehicles
with automatic transmission): 60 Nm (44 ft
lb) + additional 1/4 turn (90 )
8 -
Dual-mass flywheel or drive plate
Removing and installing Page 13
-43
9 -
Intermediate plate
Must fit on bushingsDo not damage or bend while performing
repairs
Pa
ge 2 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2

13-39

Crankshaft oil seal (toothed belt side),
replacing


Engine installed
Lock carrier in service position Page 13
-1

Special tools and equipment

2085 seal puller
3083 arbor
3099 spur belt spreading

Removing

- Remove ribbed belt and ribbed belt tensioner
Page 13
-15
.

- Remove toothed belt Page 13
-29
.

- Remove mounting bracket for torque arm
Page 17
-2 , item - 5 -.

- Remove crankshaft toothed belt gear. Secure toothed belt gear using
3099 spur belt spreading.
Pa
ge 4 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2

13-42

- Place torque arm on rubber buffer for torque arm
and tighten bolts to 25 Nm (18 ft lb).

- Install ribbed belt and ribbed belt tensioner
Page 13
-15
.

Note:
When installing the ribbed belt, make sure it is
seated correctly on the pulley.

Tightening torque

Component

Tightening torque
Toothed belt gear to
crankshaft 90 Nm (66 ft lb) +
90
1)2)

1) Replace bolt. 2) 90 are equivalent to 1/4 turn.
Pa
ge 8 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2

13-43

Dual-mass flywheel/drive plate,
removing and installing


Special tools and equipment
10-201 flywheel retainer

Dual-mass flywheel

Tightening torque - Relocate 10-201 flywheel retainer to loosen and tighten bolts.
- Mark installed position (flywheel to crankshaft) to reinstall in same
position.
- Always replace bolts. Component
Tightening torque
Dual-mass flywheel to crankshaft
60 Nm (44 ft lb) + 180
1)
1) 180 are equivalent to 1/2 turn.
Pa
ge 9 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2

13-44

Drive plate

Removing

Installing - Relocate 10-201 flywheel retainer to loosen and tighten bolts.
- Mark drive plate to engine.

- Install drive plate with shim -2- and mounting washer -1-. Lug (arrow)
must point toward torque converter.
- Insert at least three used mounting bolts and tighten.
Tightening torque: 30 Nm (22 ft lb)
Pa
ge 10 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2

13-45


If the specified value is exceeded: - Measure distance -a- at three places and calculate average.
Specification for Automatic Transmission 01V: 26-28 mm (1.024-1.102
in.).

If specified value is obtained:
Tightening torque - Remove drive plate and reinstall without shim -2-.
- Re-tighten bolts to 30 Nm (22 ft lb).
- Repeat measurement procedure.
- Replace bolts and tighten. Component

Tightening torque
Drive plate to crankshaft
60 Nm (44 ft lb) + 90
1)
1) 90 are equivalent to 1/4 turn.
Pa
ge 11 of 11 Sealin
g flan
ge and fl
ywheel/drive
plate, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.13.2