can AUDI A3 2010 8P / 2.G RNS_E Navigation System Manual

Navigation (NAV) 160CompassFig. 174 Setup Navigation: Compass activated
– Press the function button
page 16 in the navi-
gation menu.
– Highlight Compass with a check mark


fig.174 to
activate the function.
If route guidance is not active, the vehicle orientation (compass
direction) is shown in the instrument cluster display
fig.175. If
the system recognizes the road, the road on which you are presently
driving is also shown.
Version information– Press the function button
page 16 in the navi-
gation menu.
– Select Version information
fig.174.The software version for the Navigation DVD in use is shown.
Tips
You can obtain information on updates for the Navigation DVD at an
Audi dealership.
Fig. 175 Instrument
cluster display
Example of a compass
display
SETUPSETUP

Navigation (NAV) 162
– In a destination input menu
page 117, fig.121, enter
the desired location data.
– Press the function button
page 16 in the navi-
gation menu.
– Select Set position/direction
page 161, fig.176.
– Using the crosshairs
page 149 on the map, select the
desired starting point for route guidance on the map.
– In the active side meu, select OK
page 161, fig.177.
– Set the direction of the location
page 161, fig.178 by
rotating the control knob.
– When you press the control knob, the system automati-
cally jumps back to the the Setup Navigation menu.You can calculate the route from another position than the present
vehicle location.
We recommend entering the data for the starting point into a desti-
nation input menu
page 117, fig.121 before you select the Set
position/direction. That way, the system will jump to the point
e n t e r e d i n t h e m a p d i s p l a y. I t i s e a s i e r t o s e t t h e l o c a t i o n o n t h e m a p
from this point.
You can search for the starting point using the crosshairs
page 149.
You can enter the starting point manually to calculate future routes.
When you have set the location manually on the map, you can
switch to a destination input menu to enter the destination data.
Start route guidance in Demo mode to simulate route guidance page 161.
Tips
It is only possible to set the location manually and to start route
guidance in Demo mode for a simulation if you vehicle is not
moving and GPS reception is not available
page 110 (e.g. in an
underground parking garage).
SETUP

Information (INFO)163
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Information (INFO)IntroductionSelecting information function
Navigation information can be selected using the
button.– Pr e s s t h e f u n c t i o n b u t t o n
page 16 t o d i s p l a y t h e
main information menu
fig.179.Th e m a i n i n f o r m a t i o n m e n u d i s p l a y s t h e s a m e i n fo r m a t i o n a s i n t h e
main function once the control button for the Nav-Info is
pressed.
Main information menuInformation data
Location and destination information can both be
displayed.Fig. 179 Info: Displaying the destination– Press the function button to display the main
information menu
fig.179. You are shown the destina-
tion or next stopover with address, estimated time of
arrival and distance.
– Rotate the control knob to the left. The data for the next
stopovers to the destination are displayed.
INFO
INFONAV
INFO

Information (INFO) 164
– Rotate the control knob to the right. The data for your
current location with its geographical data and the
number of receivable satellites is displayed.The main information menu provides a display of your destination
with the following data:

Destination


Stopovers


Estimated time of arrival


Distance to destination


Location of your vehicle


Geographic location of your vehicle (latitude, longitude)


Received satellites
The last navigation announcement will also be repeated.Tips
If you press the button within the Info function, you can
program sound and tuning settings using the control buttons and
adjust the brightness for the display
page 169.
SETUP

CAR 168CARIntroductionSelecting car function– Pr e ss t h e fu n c t i o n b u t to n
page 16. Th e m ai n c a r
menu or the menu for the Versi on function will be
displayed.If you select the Ve rsi on function in the main Car menu, the hard-
wa re a n d s o ft wa re s t a t us fo r t h e “Au d i N a v i g a t i o n S ys t e m p l us ” w il l
be displayed.
Tips
If you press the button within the Car function, you can
program sound and tuning settings using the control buttons and
adjust the brightness for the display
page 169.
CARSETUP

SETUP169
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
SETUPIntroductionGeneral safety precautionsEnter vehicle settings only when the vehicle is stationary. The
procedures described below would distract your attention from
traffic if you performed them while driving. Please note
page 9,
“Notes on Traffic Safety”.
Selecting Setup functionFig. 180 Display: Setup Radio
– Press the button in addition to a button already
pressed. The main Setup menu
fig.180 which is part
of the main function (e.g. radio) is displayed.
– Press one of the control buttons in a Setup main menu

page 17 to go to the submenus for the Setup function
(in the example Radio to
fig.180).The Setup menu operates in conjunction with a function button
already pressed
page 16 a n d o p e n s a d d i t i o n a l m e n u i t e m s f o r t h e
main function Radio, CD, MP3 and Navigation. By pressing the
control buttons, the Setup submenus Settings, Sound and Display
can be opened
fig.180. These Setup submenus are always the
same, regardless of which Setup main function you are in.
SETUP
A1
A3

SETUP 170The following submenus are available in the Setup
function:
Tips
You can read about system-specific Setup settings functions in the
description for each primary function.
Settings control buttonSetting the menu language
Display texts can be shown in different languages.Fig. 181 Setup: Menu language setting–Press the Settings control button in the Setup menu.
– Select Menu language
fig.181.
– Select the desired menu language.The display texts for the Navigation System are changed to the
selected language. The language for the audible navigation
commands are also changed.
The following languages can be selected:
Control button
functions 
page 169,
fig. 180
Setup submenus

Settings
Menu language
Distance unit
Time/Date format
Factory settings
Delete user data

Sound
Balance
Fader
Tr e b l e
Bass
DSP
a)b)

Volume settings (Navigation info)
a)Digital Signal Processingb)Vehicles with a BOSE® sound system in conjunction with an AudioPilot do
n o t h av e a D SP f un ct i o n. I n th is c as e y o ur v e hi cl e is equ ip p ed w i th d y n am ic
noise compensation
page 94.
Display
Switch off display
Brightness
A1AA3

SETUP171
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP


German


English


French


Italian


SpanishTips
The menu language can only be selected when the vehicle is
stationary. The function is greyed out while you are driving and
cannot be selected.Setting distance unit (km/miles)Fig. 182 Setup: Distance unit–Press the Settings control button in the Setup menu.– Select Distance unit.
– Select from the units miles or km.
Time/Date format
Time of day and date can be adjusted through the
preset formats.Fig. 183 Setup: 12h time format settingSetting time format
–Press the Settings control button in the Setup menu.
– Select Time/Date format
fig.182.
– Select Time format
fig.183.

SETUP 172
– Choose between the display 12h and 24h.
Setting date format
–Press the Settings control button in the Setup menu.
– Select Time/Date format
page 171, fig.182.
– Select Date format
page 171, fig.183.
– Choose between the display MM/DD for the format
“Month/Day” or DD.MM for the format “Day.Month”.The instruments cluster acts as the source for the time and date
display.
If the instrument cluster source is not available for some reason, the
time and date are received via the GPS. In this case GPS shows
under the menu item Time source GPS time can be set through the
menu item GMT +/-
Tips
If the instrument cluster source should not be available, please
contact an Audi dealership or authorized facililty.
Factory settings
Settings can be reset to prespecified default settings in
this function.Fig. 184 Setup: Settings factory settings–Press the Settings control button in the Setup menu.
– Select Factory settings
fig.184.
–Confirm Reset system to factory presets? with Ye s. The
settings (e.g. Setup Navigation and route criteria) are
reset to default settings.User data are not deleted.

SETUP173
General operation
RADIO, CD
NAME, TEL
NAV, INFO
CAR, SETUP
Delete user data
User data in the Navigation System can be deleted.–Press the Settings control button in the Setup menu.
–Select Delete user data
page 172, fig.184.
–Confirm Are you sure you want to delete all user data??
with Ye s. User data (e.g. directory data, previous destina-
tions, radio memory list) are deleted.Sound control buttonSound settingsThe explanations for the sound settings start with section page 92.
Display control buttonSwitch off displayFig. 185 Setup: Switch off displaySwitch off display
–Press the Display control button in the Setup menu.
– Select Switch off display
fig.185. The display is
switched off, the systems for navigation remain active.
Switch on display
– Press or rotate the control knob
page 17, or
–Press a
page 16 function button, or