spare wheel AUDI A3 2011 Owner´s Manual

111.___W_ h_ a_t _ d _ o_ I_ d_ o_ n_o _w_ ? ___________________________________________ _
-Put the tool case and the jack back in place in the luggage
compartment .
- Check the
tire pres su re on the spare wheel immediately
after mounting i t.
- As soon as possible, have the
tightening torques on all
wheel bolts checked with a torque wrench. The correct
tightening torque is 90 ft lb (120 Nm).
- Have the flat tire
repl aced as soon as possible.
lIJ Tips
• If you notice while changing a tire that the wheel bolts are
corroded and difficult to turn, then they should be replaced before
you check the tighten ing torque .
• Drive at reduced speed until you have the tighten ing torques
checked .a
A pplies to veh ic les : wi th full wh ee l cove rs
Full wheel covers
The wheel covers must be removed to access the wheel
bolts .
Removal
-Pull the full wheel co ver off manually.
Installation
- First press the full wh eel c over onto the rim at the cut -out
provided for the valve . Then engage the outer edge of the
full wheel cover in the steel rim.•
A ppli es to veh icles : wi th deco ra ti ve whee l cov ers
Decorative wheel covers
The decorative wheel covers must be removed first to
access the wheel bolts .
Removing
Fig. 185 Wheel
c h ange: removing the
whee l cover
- Insert the hoo k provided with the on board tool kit into the
hole on the center hub piece.
- Pull off the
decorative wheel cover=> fig. 185 . •

lffll.,___W_ h_ a_t _ d_ o_ I_d_ o_ n_o _w_ ? ___________________________________________ _
Taking the wheel off/putting the spare on
Follow these instructions step-by-step for changing the
wheel
M
"' ;;; u.
1li
Fig . 191 Wheel
change: using the
screwdriver handle
(with the blade
removed) to turn the
bolts
Fig. 192 Wheel
change: alignment pin
inside the top hole
After you have loosened all wheel bolts and jacked the vehicle
off the ground, perform the following steps to remove and
replace the wheel:
Removing the wheel
- Use the hexagonal socket in the screwdriver handle to
completely turn out the topmost wheel bolt and set it
aside on a
clean surface=> fig. 191. -
Screw the threaded end of the
alignment pin from the
tool kit hand-tight into the now vacant bolt hole
=> fig. 192.
- Then completely unscrew the other wheel bolts as
described above.
- Take off the wheel leaving the alignment pin in the bolt
hole=> &.
Putting on the spare
- Lift the spare wheel up and carefully slide it over the align­
ment pin to guide it in place.
- Use the hexagonal socket in the screwdriver handle to
screw in and tighten all wheel bolts
slightly.
Unscrew the alignment pin and insert and tighten the
remaining wheel bolt slightly like the rest.
- Turn the handle on the jack counter-clockwise to lower the vehicle until the jack is fully released.
- Use the wheel bolt wrench to tighten all wheel bolts firmly
=>
page 276. Tighten them crosswise, from one bolt to
the (approximately) opposite one, to keep the wheel
centered.
& WARNING
When removing or installing the wheel, the rim could hit the
brake rotor and damage the rotor. Work carefully and have a
second person help you.
(I) Tips
Never try and use the hexagonal socket in the handle of the screw-
driver to loosen or tighten the wheel bolts.
~

_____________________________________________ W __ h_a_ t_ d_o_ I_ d_o _ n_ o_ w _ ? __ _
• Pull the reve rsible b lade from the screwdriver before you use the
hexagon al so cke t in the handle to turn t he whee l bolts .
• When mounting tires with
unidirectional tread design make sure
t he t read pa ttern is po inte d the r ig ht way =:>
page 2 79.
• The wheel bo lts shou ld be clean and easy to turn. Check for dirt
and corrosion on the mat ing surfa ces of both the whee l and the hu b.
Remove all d irt from these s urfaces before remounting the whee l.•
Tires with unidirectional tread design
Tires with unidirectional tread design must be mounted
with their t read pattern pointed in the right direction .
Using a spare tire w ith a tread pattern intended for
u se in a specific direction
When using a spare tire w ith a tread pattern intended for use in a
spec ific direction, please note t he fo llow ing:
• The direct ion of rotation is marked by an arrow on the side of the
tire.
• If the spare tire has to be installed in the incorrect direction in the
event of a flat ti re, use the spare tire only temporari ly since the tire
wi ll not be able to achieve its optimum pe rformance characterist ics
with regard to aq uaplaning, noise and wear .
• We recommend that particular attention be paid to this fact
during wet wea ther and that you adj ust you r speed to match road
conditions .
• Rep lace t he flat tire w ith a new one and have it ins talled on your
vehicle as soon as poss ible to restore the handling advantages of a
properly pointed direction -dependent tire .•
Safety first
Notes on wheel change
Please read the information =:> page 257, "New tires and rep lacing
ti res and wheels" if yo u are go ing to use a sp are t ire wh ich is diffe rent
from the tires on your vehicle.
After you change a tire:
• Che ck the tire pres sure on the spare immediately after
mounting .
• Have the wh eel bolt tight ening t orque ch ecked with a torque
wrench a s soon as poss ible by your authorized Audi de aler or a qual ­
ified servi ce station.
• On steel and allo y wheel rim s, the wheel bolts are co rrectl y
tightened with a torque of 90 ft lb (1 20 Nm ).
• If you not ice while ch anging a tire that the wheel bolt s are
corroded and difficult to turn, then they should be r eplaced before
yo u che ck the tightening torque.
• Repla ce the flat tire with a new one and have it installed on your
vehicle a s soon a s po ssible . Remount the wheel c over.
Until then, drive with e xtra care and at reduced speed s.
& WARNING
• If you ar e going to equip your vehicle w ith tire s or rims which
differ from tho se which were factor y installed, then be sure t o
read the information =:>
page 257, "New tires and replacing ti re s
and wheels ".
• Alway s make sure the damaged wh eel or even a flat t ire and
the jack and tool kit a re properly secured in the lugg age compart­
ment and ar e not loo se in the pa ssenger compartm ent .
• In an accident or sudden maneuver th ey could fly forward ,
injur ing anyone in the vehicle .
• Alway s store damaged whee l, jack and t ools se cure ly in
luggage compartment. Otherwise, in an accident or sudde n
Vehicle care Do-it-yourself service Technical data

.,,___G_ e_ n _ e_ r_ a_ l_i_n _f_o _ r_ m __ a_t _ i_o _n _______________________________________________ _
General information
Explanation of technical data
Some of the technical data listed in this manual requires
further explanation.
The technical data for your vehicle is listed in the charts starting on
~ page 296. This sect ion prov ides genera l information, notes and
restrictions which app ly to this data .•
Veh icle identification
The key data are given on the vehicle identification
number (VIN) plate and the vehicle data sticker .
Fig. 20 5 Vehi cle I den ­
t ifi ca tion Nu mbe r
(VIN) pla te : loc atio n
o n d rive r's sid e d ash
p an el Fi
g. 2 06 Th e vehicle
identi ficati on l abel -
in side the l ugga ge
co mpa rtme nt
The Vehicle Ident ifi cat ion Number (VIN)
is located on the dr iver's s ide so that it is visible from the outside
through the windsh ield -see~ fig. 205 .
The vehicle identificati on label
is located in the luggage compartment in the spare wheel well.
The labe l~ fig. 206 shows the following vehicle data:
© Production control no.
@ Vehicle identification no.
@ Type code n umber
© Type designat io n/eng ine output in Kilowatts
© Engine and transmiss ion code letter
© Paint no./Interior
0 Optional equipment no.'s
Vehicle data 2 to 7 are also found in your Warranty & Maintena nce
booklet.
The safety comp liance stick er
is your assurance that your new vehicle complies w ith all applicable
Federal Motor Veh icle Safety Standa rds which we re in effect at the
time the vehicle was manufactured. You can find this sticker on the ._

____________________________________________ _::C :.:o::.:...: n:..:s =..=u::.. m :....:.:..:: e:..:.r...: I ~n:..:...'.. f.::o ~r...:. m~ a~ t~ io~ n'..- __
& WARNING (co ntinued )
been remo ved. The radiator fan switches on automatically when
the coolant reache s a certain temperature and will continue to run
until the coolant temperatu re drops.
• Always remove the ign ition key before anyone gets under the
vehicle.
• Alway s support your v ehicle w ith safety stands if it i s nece ssary
to work underneath the vehicle. The jack supplied with the vehicle
is not adequate for th is purpose and could collapse causing
serious personal injury.
• If you must work underneath the vehicle with the wheels on
the ground, always make sure the vehicle is on level ground , that
the wheels are always securely blocked and that the engine cannot be started.
• Always make sure the transmi ssion selector lever (automatic
transmission) is in "P" (Park position ) (automatic transmission)
or Neutral (manual transmission) and the hand brake is firmly
applied.
'i> For the sake of the environment
• Chang ing the engine settings will adversely affect emiss ion levels.
Thi s is detr imenta l to the environme nt and increases fue l co nsump ­
tion .
• Alw ays obse rve enviro nmen tal regula tion s when dis pos ing of o ld
eng ine oil, used brake fl uid, d irty engine coo lant, spent batter ies or
wo rn out t ires .
• Undeployed a irbag modules and pretensione rs m ight be classi fied
a s Pe rchlo ra te Ma ter ia l -s pec ia l han dlin g m ay apply , see
www.dtsc.ca.gov/hazardouswaste/perchlorate. When the vehicle or
part s of th e re st ra int system i ncludi ng air bag modu les s afe ty belts
with pretens ioners are scrapped, all applicable laws and regulat ions
must be observe d. Yo ur a uthor ized Au di dealer is f amiliar wi th these
requirements and we recommend that you have your dealer perform
this service for yo u.•
Safety first
Additional accessories,
modifications and parts
replacement
Additional accessories and parts
replacement
Always co nsult an autho riz ed Audi d ealer bef ore
p urchasing acces sories.
Yo ur vehicle incorporates the latest safety design feat ures ens uring a
high standard of active and pass ive safety .
Th is safety could be compromised by non-approved changes to the
veh icle . F o r th is reaso n, if p arts have to be rep la ce d , ple ase obse rve
the following points when installing addit ional accessories:
Approved Audi accessories an d genuine A udi parts are avai lable from
au thori zed Aud i dea le rs .
These dea lers a lso have the necessary facilities, tools and tra ined
specialists to i nstall t he pa rts and ac cesso ries properly.
& WARNING
Using the wrong spare parts non-approved accessories can cause
damage to the vehicle and serious per sonal injury.
• Use only accessories expressly approved by Audi and genuine
Audi spare parts
• These parts and accessories have been specially designed to be
used on your vehicle.
• Never install accessories such as telephone cradles or beverage
holder s on airbag covers or within the airbag deployment zones .
Doing so will increase the risk of injury if airbags are triggered in
an accident!
• Before you check anything
in the engine compartment, always
read and heed all WARNINGS~
page 218. .,
Do-it,yourself service Technical data

-Alphabetical inde x -~ =-.::..::..:.==.:.....:.:...:.=.=.:.: ___________________ _
Seats
Number of seats
135
Selector lever positions
Automatic transmission . . . . . . . . . . .
115
Service and disposal
Safety belt pretensioner .. .........
144
Service interval display .. .............. 27
Service position fo r windshield wipers ... 68
Set menu .................. ... .. .. . 25
Setting
Date display ................. .. .. ..
9
Digital clock .............. ... .. .. .. 9
Side airbags
Description . ....................
161
How they work .................. 162
Side curtain airbags .... .. .. .. .. ..... 164
Description .. .. ................. 164
How they work . .. ...... ......... 165
Safety instructions ............ ... 166
S ide marker lights ..... .............. 56
Ski sack .. .. .... .. .. ................ 85
Snow chains 262
90
Sockets .. .. .. .. .. .. .. .... .. .. .. ... .
Sound system Rep lacing . ... ..... ..............
302
Sound system display . .. ... ........ .. . 18
Sources of information about child restraints
and their use ........... ...... ..
186
Spare tire .. .................... ... 271
Spare wheel
See Spare tire ............ .... ... 271
Speed rating letter code .... .. ... .... 259
Speed warning ... .. ..... ..... ..... .. 35
Speed wa rning system ......... ... .. .. 28
Speedometer . . . . . . . . . . . . . . . . . . . . . . . 10
Starting assistance ........... .. .. ... 288
Starting on hills
H ill hold assist ........... .. .. .. .
110
Starting the engine .......... .. . 106, 107
What should I do if the engine does not
start? ....... .... .. .... .......
107
Steel wheels ................ .. .... . 212
Steering ................... .. .... . 105
Locking the steeringi ........ ...... 106
See also Electro-mechanical power assist .
17,193
Steering wheel column
Ad'
t' JUS rng .... .... .. .. .. .... .... .
Steps for determining correct load limit
Stopping the engine ... ............. .
Storage ............. ... ... . ... ... . .
105
254
108
91
Compartments in the door trims ..... 93
Cup holder rear center armrest .... .. 89
Glove compartment ....... .. .... .. 92
Small objects ......... .... .. .... .. 92
Storage compartment
Increasing size ..... .... .... .. .. ..
81
Sun visors .......................... 63
Sunroof
See panoramic sliding sunroof ..... .. 51
Switches
Emergency flasher ........ .. .. .. ..
59
Switching the air conditioner (automatic)
on/off ......... ... .. .... ........
97
Symbols
T
Red symbols in the center display 30
Yellow symbols in the center display .. 30
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tailgate
See Rear lid .. .. .. .. .............. 45
Technical modificat ions . ....... .. .. .. 302
Temperature
Climate controls . . . . . . . . . . . . . . . . . .
98
Setting for the driver's and front passen-
' 'd ger s s1 e ..... ... ............... 98
Tether anchors .. .... .. ............. 184
Tether strap ........... .. .... .... .. 184
Th e first 1,000 miles (1,500 km) and
afterwards ... .......... ... . ...
197
Tie-downs .............. ........ 82, 132
Tips for the environment
Saving fuel ...... .. .. .. ......... .
89
Tire pressure .... ....... ...... .... .. 252
T ir e pressure monitoring system ..... . 264
Loss of air pressure ............ 13, 265
Malfunction ... .... ............. . 265
Resetting tire pressures .. ......... 267
Warning light ............. .. . ... . 36
Ti re service life .. .. .. .. .............
Tires .................. ... .. .. ' .. .
Replacing .. ............ .... .... .
Service life . .... .. .. .. .. ..... .. . .
speed rating letter code .......... .
Tir e manufacturing date .. ........ .
256
245
257
256
259
259