check oil AUDI A3 2012 Owner´s Manual

unbalanced, resulting in vib rations you can
usually feel through the steering wheel.
Unba lanced wheels mus t be rebalanced to
avoid excessive wea r on s teer ing, suspens ion
and tires. A wheel must a lso be rebalanced
when a new tire is installed.
Incorrect wheel alignment
Inco rrect whee l alignment can cause exces­
sive tire wea r, impair ing t he safety of the veh i­
cle. If t ires show excess ive wear, have the
wheel alignment checked by an authorized
Audi dealer or qualified workshop.
All Wheel Drive
Ve hicles w it h quattro ® must always have t ires
of the same s ize, construction and tread type.
F or details see
¢ pag e 166 .
A WARNING
Sudden tire failure can lead to loss of con­
tro l, a crash and serious persona l injury!
- Never drive a veh icle when the tread on
any t ire is worn down to the wear indica­
tors.
- Worn tires are a safety hazard , they do
not grip well on wet roads and increase
your risk of"hydrop lan ing" and loss of
co ntrol.
- Always keep chemicals that can cause
tire damage, such as grease, oil, gasoline
and brake fluid away from tires.
- Tires age even if they are not being used
and can fail suddenly, especially at high
speeds. Tires that are more than 6 years
old can only be used in an emergency and then with special care and at lower
speeds .
- Never mount used tires on yo ur vehicle if
you are not sure of their "previous histo­
ry." Old used tires may have been dam­
aged even though the damage cannot be
seen that can lead to s udden tire failure
and loss o f vehicle con trol.
Tires and wheels 223
New tires and replacing tires and wheels
New tires and wheels have to be broken in .
Fig. 171 Tir e spec ification codes on t he sid ewall o f a
t ire
No . Desc ription
(D Passenger car tire (where applicable)
@ Nomina l w idth of t ire in mill imeters
@ Ratio of height to width (aspect ratio)
© Rad ial
® Rim diameter code
@ Load index and speed rating
(J) U.S. DOT tire identification number
@ Aud i Origina l tire
® Tire ply composition and materials
used
@
@
M axim um load rating
Treadwear, traction and temperature
I
grades Maxim um permissible inflation p res­
sure
T he tires and rims are essential parts of the
vehicle's des ign . The tires and rims approved
by Audi are specia lly matched to the charac ­
teristics of the ve hicle and can make a major
contribution to good road holding and safe ..,.

@ Tips
-Where snow chains are mandatory on
certain roads, this normally also applies
to vehicles with All Wheel Drive .
- If snow chains are insta lled, the tire
pressures shou ld not be stored in the tire
pressure monitoring system (TPMS).
Otherwise the system could malfunction
¢page 232.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of whee l bolts is matched to the
factory installed rims. If different rims are fit­
ted, the correct wheel bolts wit h the right
length and correctly s haped bolt heads must
be used. This ensures that wheels are fitted
secure ly and that the bra ke system f unctions
cor rectly .
In certain circumstances, you may not use
wh eel bolts from a differ ent vehicle -even if it
i s the same mode l.
.&, WARNING
Improperly tig hte ned o r maint ained wheel
bol ts can become loose ca using loss of
cont ro l, a co llision and ser ious persona l in ­
jury.
- Always keep the wheel bolts an d the
threads in the wheel hubs clean so the
whee l bolts can tu rn easily and be pro p­
er ly t ightened.
- Never grease or oil the wheel bo lts and
the threads in the w heel hubs. They can
become loose w hile driving if greased or
o iled, even if tightened to the specified
torq ue.
- Only use wheel bolts t hat belong to the
r im being installed.
- Never use different whee ls bolts on your
vehicle.
- Always maintai n the co rrect tighten ing
torq ue for the wheel bo lts t o reduce the
risk of a wheel loss. If the tightening tor-
Tire s an d wheel s 229
que of t he whee l bolts is too low, they
can loosen and come out when the vehi­
cle is mov ing. If the tig htening torq ue is
too high, the wheel bolts and threads
can be damaged and the whee l can be­
come loose.
(D Note
The specified torque for the whee l bolts is
90 ft lb (120 Nm) with a tolerance of± 7,4
ft lb(± 10 Nm). Torq ue whee l bolts diago­
nally. After changing a whee l, the tor que
must be checked as so on as possible with a
torq ue w rench -prefe rably by an au thor ­
iz ed A udi de aler or qu alified workshop .
Low aspect ratio tires
Your Audi is factory -eq uipped w ith low aspect
r atio tires . These tires have been tho ro ughly
tested and been se lected specifically for your
model for their superb performance, road fee l
and handli ng u nder a var iety of driving condi­
tions . Ask your au thorized Aud i dealer for
more d etails.
The low aspect ratio of these t ires is ind icated
by a numeral of
55 or less in the tire's s ize
designation . The numera l represen ts the ratio
of the t ire's sidewa ll height in relation to its
t read width exp ressed in perce ntage. Conven­
tiona l tires have a he ight/w idth ratio of 60 o r
more.
The performance of low-a spect-ratio tires i s
particularly sensitive to improper inflation
pre ssure.
It is therefore important that low
aspect ratio tires are inflated to the specified
pres sure and that the inflation pressure is
regularly checked and maintained. Tire pre s­
sures should be checked at least once a month and always befo re a long trip
¢ page 218, Checking tire pressure.
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged mo re
easily by impact w it h potholes, curbs, gul lies ..,.
•
•

-The vehicle should never be lifted or jacked
up from underneath the engine oil pan , the
transmission housing , the front or rear
a x le or the body side members. This could
lead to ser ious damage.
- Use lifting equipment with padded contact
surfaces to avo id damage to the underbody
or chassis frame.
- Alternatively, cover the contact surfaces on
workshop hoist or floor jack w ith rubber
pads b efore lifting.
- Before dri ving over a workshop hoist, check
that the vehicle weight does not exceed the
permissible lifting capacity of the hoist .
- Before dr iving over a workshop hoist, en­
sure that there is sufficient clearance be­
tween the hoist and low parts of the vehi­
cle .
A WARNING
To r educe the ris k of seriou s injury a nd ve­
hicle da mage:
- Always lift the veh icle only at the spec ial
wor ks ho p hoi st and floor j ack lift p oin ts
ill ustra te d
c:;>page 253, fig. 199 and
c:;>page 253, fig . 20 0.
- F ailure to l ift the vehicl e at th ese poi nts
cou ld ca use the ve hicle to t ilt or fall from
a lift if there is a c ha nge in vehicle wei ght
dist rib ution and balance . This might hap ­
pen, for example, when heavy c ompo­
nents such as the e ngine bloc k or t rans­
mission are removed.
- W hen remov ing s uch heavy c omponents,
anchor veh icle to h oist or add corre­
sponding we ights t o maintain the center
of g rav ity. Oth erwise, th e veh icle m ig ht
t il t o r slip off the hois t, causing serio us
p ers onal in ju ry.
Emergency situations 253
Lifting with workshop hoist and with
floor jack
T he vehicle may only be lifted at the li~ing
p oi nt s illus tra ted.
..,
---------~1::
Fig. 199 Front lifting point
Fig. 200 Rear lifting point
.,. Read and heed WAR NIN G c:;> &. in Impor ­
tant safety precautions on page 253 .
.,. Locate lifting points c:;> fig. 199 c:;> fig . 200 .
.,. Adjust lifting arms of workshop hoist or
fl oor jack to matc h ve hicle lift ing poi nts.
I
.,. Insert a rubbe r pad between the floo r jac k/
workshop hoist and t he lift ing poin ts .
If you must l ift your vehicle with a floor jack
to work underneath, be sure the vehicle is
safely supported on stands intended for this purpo se .
Front lifting point
The lifting poi nt is located o n the floo r pan re­
inforcement about at the same leve l as the
jac k mounti ng po int
c:;> fig. 199. Do not lift
the vehicle at the vertical sill reinforcement .
Rear lifting point
The liftin g point is located on the vert ica l rein­
forcement of the lower s ill for the on board
jack
c:;> fig. 200. ..,.

254 Emergency situations
Lifting with vehicle jack
Refer to"* page 239.
(D Note
-Be aware of the following points before
lifting the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine
oil pan, the transmission housing, the
front or rear axle or the body side members. This could lead to serious
damage.
- To avoid damage to the underbody or
chassis frame, a rubber pad must be
inserted between the floor jack and
the lift points.
- Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity
of the hoist.
- Before driving over a workshop hoist,
ensure that there is sufficient clear­
ance between the hoist and low parts
of the vehicle.

-If you must work underneath the vehicle
with the whee ls on the ground, always
make sure the vehicle is on level ground,
that the wheels are always secu rely
blocked and tha t the eng ine cannot be
started.
- Always make sure the transm ission se­
lector lever (automatic transmiss ion) is
in "P" (Pa rk position) (a utomat ic trans­
mission) or Neutral (manual transmis­
sion) and the hand brake is fi rm ly ap­
plied.
@, For the sake of the environment
- Changing the eng ine settings w ill ad­
versely affect em ission levels. This is det­
rimental to the environment and increas­
es fue l cons umption.
- Always obse rve env ironmental regula­
tions when d ispos ing of old engine oil,
used b rake fluid, dirty engine coolant,
spent batteries or worn out tires .
- Undeployed airbag modules and preten­
s ioners might be classified as Perchlo­
rate Mate rial -special handling may ap­
ply, see www.dtsc.ca.gov/hazardous­
waste/perchlorate. When the veh icle or
parts of the restraint system includ ing
airbag modules safety belts with preten­
s ioners are scrapped, all appl icable laws
and regulations must be observed. Your
autho rized Audi dea le r i s familiar w ith
these req uirements and we recommend
that yo u have your dea le r perform this
service for you.
Additional accessories, modifications and
parts replacement
Additional accessories and parts
replacement
Always consult an authorized Audi dealer be­
fore purchasing accessories .
Your vehicle incorporates the latest safety de­
sign features ensuring a high standard of ac­
tive and passive safety .
Consumer In formation 26 1
This safety could be compromised by non-ap ­
proved changes to the vehicle . For this reason,
if parts have to be replaced, please observe
the following points when installing add ition­
al accessories:
Approved Audi accessories and genuine Audi parts are available from authorized Audi deal­
ers.
T hese dea lers a lso have the necessary facili­
ties, tools and trained specialists to install the parts and accessories properly .
_& WARNING
Using the wrong spare parts non-approved
accessories can cause damage to the vehi­
cle and serious personal injury.
- Use on ly accessories expressly approved
by Audi and genu ine Audi spare parts
- These parts and accessories have been
specially designed to be used on your ve­
hicle.
- Never install accessor ies such as tele­
phone cradles or beverage ho lders on air­
bag covers or within the airbag deploy­
ment zones. Do ing so will increase the
ris k of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNINGS
<:!)page 187.
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used o r if repair wo rk is not
performed accord ing to specified meth­
ods, this can resu lt in severe damage to
your vehicle's engine and body (such as
corrosion) and adve rsely affect yo ur vehi­
cle 's warranty.
- If emergency repairs must be performed
elsewhere, have the vehicle examined by
an authorized Audi dealership as soon as
possible.
- The manufacturer cannot be held liable
for damage wh ich occ urs due to failure
to comply with these stipulations.
•
•

26 6 Index
Changing engine oil
Chass is 201
Unde rcoat ing . ............. .. .... . 183
also refer to Aud i magnetic ride ... .... 95
Checking
Eng ine coolant level ........ .... ....
204
Checking tire pressure . ... .. .. ... ... . 218
C hi ld restra int
Danger of us ing c hild restra ints in the
front seat ... .... ..... ... .. .. .... .
123
Child restra ints
Where can I get add it iona l information
about child restra ints and their use? ..
160
Ch ild restra int system anchors ... .. ... 155
Child safety . . . . . . . . . . . . . . . . . . . 143, 148
Convertible locking retractor . . . . . . . . . 152
Important safety instructions for using
chi ld safety seats ..................
146
Important things to know when dr iving
with children ............. .... ....
143
Install ing a child restraint using the
LA TC H system ............. ... .. ...
157
M ount ing and releasing the ancho rage
hook .. .... ... .......... .. .. .. .. .
157
158
158
Tether anchors
Tether straps
Ch ild safety lock
· ............... ..... 42
Child safety seats ................... 148
Booster seats .. .......... .. .. .... . 151
Convertible child seats .... .. .. .. .. . 149
Convertible locking retractor .. .. .. ... 152
H ow do I properly install a child safety
seat in my vehicle? ........ .. .. .... .
146
Infant seats ...................... 148
Ins tall ing ... ............ .. .. .. .. . 152
LA T CH system .... ..... ... .. .. .... . 157
Safety instructions . . . . . . . . . . . . . . . . . 146
Child seats
L owe r ancho rages ........ .. .. .... .
156
Clean ing
Alcantara (synthet ic suede) ..........
186
Eng ine compartment ...... .. .. .. .. . 187
Exhaust tail pipes .................. 183
Fabrics and fabr ic coverings .. .. .... . 184
Instrumen t panel .................. 184
Inter ior
L eather .. .. ... .. ..... ... .. .. .... .
. ... ... . ...... ... ... ...
' . .
183
186
Plastic and vinyl ..... .. ..... .... . .. 181
Plastic parts ..... ... .. ..... ... .. .. 184
Safety be lts ... .. ... ....... ... .. .. 187
trim strips
Tr im strips 181
181
Cleaning and protection .. ..... ... .. .. 178
Cl imate controls . .. ................ .. 79
Additional heater . ... .......... .. .. . 85
Air distrib ution . .. ............. .... . 83
Air o utlets · · · · · · · · · · · · · · · ......... 84
Air recirculation . . .. ... ..... .... ... . 83
Air recircu lation mode (manual) . ... .. . 82
Automatic air recirculation ... .... . .. . 82
AUTO (standard setting) ........ .. .. . 81
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Defrost ing/defogging ............. .. 82
Description . . . . . . . . . . . . . . . . . . . . . . . . 79
Fan ......... ... .. .............. .. 83
Key- coded setting ... .......... .. .. . 84
Recommended settings ......... .... . 79
Setting the temperatu re ........ .. .. . 82
Switching between Fa hrenhe it and Centi-
grade . ... .... .. .. .... .... ... .. .. .
83
Switching the air conditioning on and off 81
Using the climate control economically . 84
Warm and cold . .. ............. .... . 79
Clock . ... .. .... .. .. ... ..... ... .. .. . 11
Clutch overheat ing ................. . 101
Coat hooks ..... .. ............. .... . 78
Cold tire infla tio n press ure ........ .... 216
coming home ... .................. .. 48
Compartments in the door trims ... .. .. . 77
Compass mir ro r . . . . . . . . . . . . . . . . . . . . . 59
Compliance . .... .. ............. .... 262
Consumer Information. .. ..... .. 111,259
Contacting NHTSA ................. . 111
Convenience close/open feature
Windows . .... .. ............. .... .
44
Convertib le child safe ty seats ..... .. . . 149
Convertible locking retractor
At· .
c 1vatmg ... .. .. .. ... ....... ... . .
154
D t" t· eac 1va mg ... .. ............. .. .. 155
Using to secu re a child safety seat 1.52, 154
Coolant system ..................... 203
Cooling System
Expansion tank ... .. .... .... ... .. ..
204

268 Index
Eme rgency towing ......... .. .. .... . 251
E ne rgy management ........... .. ... 167
Ba ttery power ........... .... .. .. . 168
Dr iver notific ation ...... .. .. .. .. .. . 16 8
Eng ine
4-cylinder diesel (140 hp) ....... .... 197
4-cyl ind er g asoline (200 hp) .. .. .. ... 196
Coolant .. ... ............ .. .. .. .. . 203
H ood .. ...... ........... .. .. .... . 194
Pr ehea ter . . . . . . . . . . . . . . . . . . . . . . . . . 86
Start ing . . . . . . . . . . . . . . . . . . . . . . 89, 90
Starting with j umper cab les . ..... .. . 248
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . 91
E ng ine compartmen t ................ 196
Safety instruc tions .......... .. .... . 194
Working in the engine compar tment .. 194
Eng ine coolant system ........... .... 203
Adding coo lant ............ ... .. .. . 204
Chec king coolan t leve l ..... .. .. .... . 204
Che cking the eng ine coolant leve l ..... 204
M alfunct ion . . . . . . . . . . . . . . . . . . . . . . . 17
Radiator fan . .. .. ..... ... .. .. .... . 205
E ng ine coolant temperature
Gauge ... .. ................ ... .. .. 11
Eng ine data .. ............... ...... . 257
Engine fault Warning light .. .. ..... ... .. .. .... .. 20
E ng ine hood
C lo sing .. .. ............. .. .. .. .. . 194
Release lever . ........... .... .... . 194
Releasing and open ing . ... .. ... ... . 194
Eng ine malfunction (diesel engine)
War ning light ............ .. .. .... .. 20
Eng ine oil . ............... .. .. .... . 197
Adding .. .. ............... .... .. . 200
Addit ives . .. ................ ... ... 200
C hanging .. ... .... ...... ... ... .. . 20 1
Chec king the eng ine o il level .. .. .. .. . 200
Di ese l eng ine ............ .. .. .... . 20 2
I ndications and con ditions req uiring ex-
tra check ing . .. .. ..... ... .. .. .... . 200
Oil consumption .. ..... ... .. .. .... . 199
Oi l grades . .... . ...... ... .. .. .... . 197
Recommended oil check intervals ..... 200
Specification and viscos ity .... .. .... . 197
Specifications Diesel engine .. .... ... 202
Specifications gasoline engine .. .. ... 197
Tempe ratu re d isplay ...... .. .. .. .. . . 31 E
ngine oi l leve l . . . . . . . . . . . . . . . . . . . . . . 20
E ngine o il pressu re (malfunction) ....... 16
Engine oil sensor defective ............ 20
En gine preheate r .................... 86
C onnect ing . ..... .. ... ..... ... .. .. . 86
E ngine speed limitation . . . . . . . . . . . . . . . 20
Environment Break-in per iod . .. ............. .... 169
Catalytic converter ............. .... 170
Diesel particulate f ilter ............ . 171
D ispos ing of your veh icle battery ... .. 210
D riv ing at high speeds .............. 172
D riving to minimize pollution and noise 171
F uel ............................. 192
F uel economy . . . . . . . . . . . . . . . . . . . . . 171
Leaks under your vehicle ..... ... .. .. 194
Letting the vehicle stand and warm up . 172
Proper d isposal of drained bra ke fluid . 206
Proper disposal of drained eng ine cool-
ant ............................. 204
Proper d isposal of drained eng ine
o il . . . . . . . . . . . . . . . . . . . . . . . . . 200, 201
Recycling used engine oil ............ 200
U nleaded fuel . ... ................ . 189
Wha t shou ld I do w ith an o ld b att ery? . 210
EPC
refer to E lect ron ic power co ntrol ... .. . 19
Event Data Recorder (EDR) ........ .... 161
E xh aus t tai l pipes
Cleaning .. .... .. ............. .... 183
Expansion tank .. .. ................ . 204
Exterior mirrors Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . 53
Dimming .......................... 54
Heating ........................... 53
F
Fahrenheit
Switching between Fa hrenhe it and Centi-
grade ....... .... .... ........... .. 83
F an
Adjusting the fan speed ...... .... . .. . 83
Climate controls ............... .. .. . 83
Radiator ......................... 205