ESP AUDI A3 2016 Owner´s Manual

,....,
N
0 > co ,...., throughout your vehicle ¢page 164. The intelli­
gent energy management system wi ll keep the
engine battery charged better than veh icles w ith­
out this system . To make sure the additional
e lectrical energy is avai lab le once again after you
have changed the battery, we recommend that
you install batteries of the same type and manu­
facture on ly (the same as those installed at the
time your veh icle was de livered). Specifications
are listed on the battery housing. Your author­
ized dealer must code the battery in the energy
management system to enable you to use the en ­
ergy management functions correctly after re­ p lacing the battery.
The new battery must have the same capacity,
voltage (12 -volts), amperage, construction and
p lug sealing .
When insta lling the battery, ma ke sure the igni­
tion and all e lectrical consumers are switched
off .
(D Note
Ma ke sure the ventilation hose on the side of
the battery is connected, otherw ise fumes o r
battery acid can leak out .
@ For the sake of the environment
Because of the prob lem of proper disposal of
a ba ttery, we recommend your author ized
Audi dea ler change the battery for you . Bat ­
teries contain su lf u ric acid and lead and must
always be disposed of properly in compliance
w ith all environmental regulations. D isposing
of vehicle batteries improperly is very danger­
ous to the env ironment.
Ch eck ing and Filling
Windshield washer
system
F ig . 201 E ngin e compar tmen t: was her flui d reservo ir cap
M N
-N ~
"' m
The washer fluid reservoir W contains the clean­
ing fluid for the windshield, the rear window *
and the headlight washer system*¢
page 239,
fig. 193 .
The reservoir capacity is found in
¢ page 303.
.,. Read and follow all WARNING S before working
in the engine compartment <=>
page 236, Work­
ing in the engine compartment .
.,. Open the cap.
.,. Add the washer fluid and close the cap .
To reduce the risk of lime scale deposits on the
spray nozzles, use clean water with low amounts
of calcium. Always add w indow cleaner to the wa­
ter . When the outside temperatures are cold, an
anti-freez ing agent should be added to the water
so that it does not free ze.
(D Note
- The concentration of ant i-freez ing agent
must be adjusted to the vehicle operat ing
conditions in the respective cl imate. A con ­
c entration that is too high can lead to vehi­
cle damage.
- Never add radiator an ti-free ze or other addi­
tives to the washer fluid.
- Do not use a glass cleane r that contains
pai nt solvents, because t his could damage
t he paint.
251

Checking and Filling
Service interval display
The service interval display detects when your ve­
hicle is due for service.
The service interval display works in two stages:
-Inspection or oil change reminder: after a cer-
tain distance driven, a message appears in the
instrument cluster display each time the igni ­
tion is switched on or off . The remaining dis­
tance or time is displayed briefly.
- Inspection or oil change due: if yo ur vehicle
has reached an inspection or oi l change interval
or both intervals at the same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears briefly af­
ter switching the ignition on/off .
Checking service intervals
You can check the remaining distance or time un­
til the next oil change or next inspection in the
MMI. Select the
I MENU I button> Car> Systems *
control button > Service & control > Service in­
tervals .
Resetting the indicator
Your authorized Audi dealer or authorized Audi
Serv ice Facility will reset the serv ice interval dis­
p lay after performing service.
If you perform an oil change yourself to the Audi
specifications, you must reset the service interval
d isp lay.
To reset the display, select the
I MENU ! button >
Car > Systems * control button > Service & con­
trol
> Service intervals > Reset oil change inter­
val.
([) Note
-Only reset the oil change indicator if the oil
was changed.
- Following the service intervals is critical to
maintain ing the service life and va lue of
your vehicle, especially the engine. Even if
the m ileage on the vehicle is low, do not ex­
ceed the time for the next service.
- Calculating the time to the next oil change
i s interrupted when the ve hicle battery is
disconnected. If the vehicle is not driven for
252
a long period of time, check the mainte ­
nance schedule so that you can fo llow the
maintenance intervals.

be happy to provide more infor­
mation.
® Mud and snow capability
"M/5 " or "M+S" indicates the tire
has character istics that make it
suitable for driving on mud and
snow .
& indicates a winter tire .
@Composition of the tire cord
and materials
The number of plies indicates the
number of rubberized fabric lay­
ers in the tire. In general: the
more layers , the more weight a
tire can carry . Tire manufacturers
must also specify the materials
used in the tire. These include
steel, nylon, polyester and other
materials.
@ Maximum permitted load
This number indicates the maxi­
mum load in kilograms and
pounds that the tire can carry.
@ Uniform tire quality grade
standards for treadwear ,
traction and temperature
resistance
Tread wear, traction and temper ­
ature ranges
¢ page 271.
~ @ Running direction
g
~ ...
'° V, ....
'° ....
The arrows indicate the running
direction of unidirect ional tires .
Tires and wheels
You must always follow the speci­
fied runn ing d irection
¢ page 288 .
@ Maximum permitted
inflation pressure
This number ind icates the maxi­
mum pressure to which a tire can
be inflated unde r normal operat ­
ing conditions.
Glossary of tire and loading
terminology
Accessory weight
means the combined weight (in
excess of those standard items
which may be replaced) of auto­
matic transmission , power steer­
ing , power brakes, power win­
dows, power seats, radio, and
heater, to the extent that these
i tems are available as facto ry-in­
stalled equipment (whether in ­
stalled or not) .
Aspect ratio
means the ratio of the height to
the width of the tire in percent .
Numbers of 55 or lower indicate a
low sidewa ll for improved steer­
ing response and better overall
handling on dry pavement. .,.
255

Tires a nd wh eels
Occupant loading and distri­
bution for vehicle normal load
for various designated seating
capacit ies
Refer to the tire inflation pres­
sure label¢
page 263, fig . 205
for the number of seating posi­
tions . Refer to the table¢
table
on page 265
for the number of
people that correspond to the ve­
hicle normal load .
New tires or wheels
Audi recommends having all work
on tires or wheels performed by
an authorized Audi dealer or au­
thorized Audi Service Facility .
These facilities have the proper
knowledge and are equipped with
the required tools and replace­
ment parts.
.,. New tires do not yet have the
optimum adhesion properties .
Drive carefully and at moderate
speeds for the first 350 miles (500 km) with new tires .
.,. Only use tires with the same de­
sign, size (rolling circumference)
and as close to the same tread pattern as poss ible on all four
wheels .
260
.,.Do not replace tires individually .
At least replace both tires on the
same axle at the same time.
.,. Audi recommends that you use
Audi Original equipment tires . If
you would like to use d ifferent
tires, please note that the tires may perform differently even if
they are the same size ¢
,&.
.,. If you would like to equip your
vehicle with a tire/rim combina ­
t ion that is different from what
was installed at the factory, con­
sult with an authorized Audi dealer or authorized Audi Service
F acility before making a pur­
chase ¢&, .
The spare tire* is different from
the regular tires installed on the
vehicle -for example, if winter
tires or wide tires are installed -
then only use the spare tire* tem­
porarily in case of emergency and
drive carefully while it is in use. It
should be replaced with a regular
tire as soon as possible.
On
all wheel drive vehicles, all
four wheels must be equipped
with tires that are the same brand and have the same construction
and tread pattern so tha t the
drive system is not damaged by .,.

,...,
This can especially have a nega­
tive effect on handling, on the risk aquaplaning when driving
through water, when driving
through curve s and when brak­
ing, which increases the risk of
an accident.
Tire pressure
Fig. 204 Driver's side B -p ill ar: tire pres ­
su re lab el
-"' -,--------------- -
• ===========
= i (:=:=a : I =:: I :.. I) (':: ~) n,.......,.._,.,.. ......... _.__......, _ _.., .... _ ... l ................... . __.......... .......... ..._ .. .,,, ..
Fig. 205 Tire pressure label
The correct tire pressure for tires
mounted in the factory and for
the spare tire* is indicated on a la­ bel. The label is located on the B­
pillar ¢
fig. 204, ¢ fig. 205.
g When the vehicle is partially load-
oo
~ ed (up to 3 peop le), use the tire Ln ,...,
"' ....
Tires and wheels
pressure specified for normal
loads¢
table on page 265 . If
driving the vehicle when fully loaded, you must increase the t ire
pressure to the maximum speci­
fied pressure ¢.&, .
Checking/correcting tire
pressure
.,..Check the tire pressure at least
once per month and also check it before every long drive .
.,..Always check the tire pressure
when the tires are
cold . Do not
reduce the pressure if it increas­
es when the tires are warm .
.,..Check the label ¢
fig. 205 for
the correct tire pressure based on vehicle load.
.,..Correct the tire pressure if nec­
essary.
.,..Vehicles with Tire Pressure Mon­
itoring System*: store the modi­
fied tire pressure in the Infotain ­
ment system ~
page 273.
.,..Check the pressure in the emer ­
gency tire* /spare t ire* . Always
maintain the maximum temper­
ature that is specified for the
tire. .,.
263

Tires and wheels
Use of snow chains is o nly pe rmitted with certain
rim/t ire combinations due to tec hnical reasons .
Chec k with an autho rize d Aud i dealer or autho r­
i z ed A ud i Service Fac ility to see if yo u may use
snow chains.
Use
fine-mesh snow chains . They must not add
mo re t han 0 .53 inc h (13 .5 mm) in height, i nclud ­
i n g the chain loc k.
You mus t remove the chains when d riving on
roads that are
free of snow . W hen roads a re free
of snow, snow c hains ca n impair handlin g and
damage the t ires, and the chains w ill quickly be
destroyed.
A WARNING
Us ing inco rrect sno w ch ains or insta lling snow
chains in co rrectly can result in loss o f vehicle
c o ntrol, w hich i ncreas es th e risk of an a cci­
de nt.
(D Note
- Snow cha ins can damage t he rims/whee l
covers* if the chains com e into d ir e ct con ­
tact wi th th em. R emov e th e wh eel covers*
fir st. U se coat ed s now chai ns.
Low aspect ratio tires
Your Aud i is fa cto ry-equippe d wi th low aspec t ra­
tio tires . These ti res have been tho roughly teste d
an d been se lected specifically for yo ur model for
their superb per fo rmance, road f eel and handling
under a variety of d riving conditions . As k yo ur au ­
thor ized Audi dealer for mo re details .
The low aspect ratio of these t ires is indicated by
a nume ra l of
55 or less in the tire's size designa­
tion . The nume ra l r ep resents the rat io o f th e
tire's sidewall he ight i n relat ion to its tread width
expressed in percentage . Conventional tires have
a height/w idt h ratio o f 60 o r more .
The performance of low-aspect-ratio tires is par ­
ticularly sensitive to improper inflation pres­
sure. It is therefore important that low aspect
ratio tires are inflated to the specified pressure
and that the inflation pressure is regularly
c hecked and maintained . Tire pre ssures should
270
be checked at least once a month and always
before a long trip
~ page 263.
What you can do to avoid tire and rim
damage
Low aspect ra tio tires can be damaged more eas i­
l y by impact with potho les, curbs, gullies or
r idges on t he road , particularly if t he tire is un ­
der i n flated.
I n order to min imize the occurrence o f impact
dama ge to the tires o f your veh icle, we recom ­
men d that you observe the following preca u­
tions:
- Always main tain recommende d inf la tion pres ­
sures . Check yo ur tir e pressure eve ry 2,000
m iles (3,000 km) and add a ir if necessary .
- Dr ive ca refully on roa ds w ith potholes, deep
gullies o r ridges . The impact from dr iving
throug h or over such obstacles can damage
your t ires. Impact wit h a curb may a lso cause
damage to your tires.
-After a ny impact, immed iate ly inspect you r
tires or have them inspected by the nearest au­
thorized Aud i dealer. Replace a damaged tire as
soon as poss ible .
- Inspect your tires every 2,000 m iles (3,000 km)
for damage and wear . Damage is no t always
easy to s ee . Damage ca n lead to loss o f air and
unde rin flation, w hich co uld even tually cause
t ire f ailure . If yo u beli eve th at a ti re may have
bee n da mage d, re place the tire as soon as p os­
sible.
- These tires may we ar m ore quick ly th an oth ers.
- Please also rem emb er tha t, whil e the se tires
delive r responsive h andli ng, they may ride less
c omf ortabl y and ma ke m ore noi se th an o ther
choi ces .
Reduced performance in winter/cold season
conditions
A ll ti res are des igned for cert ain pur poses . T he
l ow aspect r atio , ul tra hig h perform ance tires
o rigina lly installed on your vehicle are inten ded
for maximum dry and wet road performance and
handling . T hey a re not suitable fo r co ld, snowy o r
i cy weather conditions. If yo u drive under th ose
c ircumstances, you should equip yo ur vehicle
with all -season o r winter tires, which offer better
11>-

traction under those conditions. We suggest you
use the recommended snow or all-season tires
specified for your vehicle, or their equivalent.
Refer to
q page 269 for more detai led info rma ­
tion regarding winter tires.
Uniform tire quality grading
- Tr ead wear
- Traction AA A B C
- Temperature ABC
Quality grades can be found where applicable on
the tire side wa ll between tread shoulder and
maximum sect ion w idth
q page 253, fig. 202.
For exampl e: T read wear 2 00 , Traction AA , Tem ­
perature
A .
All passenger car tires must conform to Federal
Safety Requirements in addition to these grades.
Trea d we ar
The tread wear grade is a comparative rating
based on the wear rate of the tire when tested
under contro lled conditions on a specified gov­
ernment test course.
For examp le, a tire graded
150 would wear one
and one ha lf
(11/2) times as well on the govern­
ment course as a tire graded
100.
The relative performance of tires depends upon
the actual conditions of their use, however, and may d epart significant ly from the norm due to
variations in driving habits, service practices and d ifferences in road characteris tics and climate.
Tracti on
The traction grades, from highest to lowest, are
AA, A, B and
C. T hose grades represent the tire's
ability to stop on wet pavement as measured un­
der controlled conditions on specified govern­
ment test surfaces of asphalt and concrete . A tire
marked C may have poor traction performance
q .&. .
,...., Temp eratur e N
0
ii; The temperature grades are A (the h ighest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to diss ipate
Tir es and wheel s
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained h igh temperatu re can cause the mate­
ria l of the t ire to degenerate and reduce ti re life ,
and excessive temperature can lead to s udden
tire failure
q .& .
The grade C corresponds to a level of perfo rm­
ance which all passenger car tires must meet un­
der the Federal Motor Vehicle Safety Standa rd
No.
109. Grades Band A represent higher levels
of performance on the laboratory test wheel than
the minim um requ ired by law.
A WARNING
-
The tract ion grade assigned to this t ire is
based on straight -ahead braking traction
tests, and does not include acceleration, cor­ nering, hyd roplaning or pea k traction cha rac­
terist ics.
A WARNING
The temperature grade for this tire is estab­
lished for a tire that is properly infl,;1ted and
not overloaded . Excessive speed, underinfla­
tion, or excessive loading, either separately or i n combination, can cause heat bui ldup and
possib le tire fai lure .
A WARNING
-
-Temperature grades apply to tires that are
p roperly inf lated and not over or under inflat­
ed.
Tire pressure monitoring system
(l) General notes
App lies to vehicles: wi th tir e pressure mo nito rin g syste m
Each tire, including the spare (if provided),
shou ld be checked monthly when cold and inflat-
ed to the inflat io n pressure recommended by the
vehicle manufacturer on the veh icle placard or
t ir e inflation pressure label. (If your ve hicle has
t ir es of a different size than the si ze ind icated on .,..
271

,....,
N
0 > co ,...., Indicator lights
IE-Loss of pressure in at least one tire c::> ,&.
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires. Then
store the tire pressures in the MMI
c::> page 2 73 .
mm (Tire Pressure Monitoring System) Tire
pressure: System malfunction!.
If m appears
after switching the ignition on or whi le driving
and the
IE indicator light in the instrument clus­
ter blinks for approximately one minute and then
stays on, there is system malfunction. Try to
store the correct tire pressures
c::> page 2 73. If
the indicator light does not turn off or turns on
again after a short period of time, drive to an au­
thor ized Audi dealer or authorized Audi Service
Facility immediately to have the malfunction cor­
rected.
A WARNING
- If the tire pressure warning light IE in the
instrument cluster turns on, the pressure in
one or more tires is too low . Reduce the ve­
hicle speed immediately and avoid any hard
steering or braking maneuvers. Stop as soon
as possible, check the tire and inflate the
t ir e to the correct pressure, which is speci­
fied on the tire pressure label on the veh icle
c::> page 263. Driving with a ti re with low
pressure causes the tire to overheat and can
result in failure of the tire. Low pressure can
also have a negative effect on the driving
and braking behavior of the vehicle .
- Th e driver is responsible for maintaining the
correct tire pressures. You must check the
tire pressures regularly.
- Under certain conditions (such as a sporty
driv ing style, winter conditions or unpaved
roads), the pressure monitor indicator may
be delayed.
- Do not use run-flat tires on your vehicle . Us­
ing them when not permitted can lead to
vehicle damage or accidents.
(D Tips
- The tire pressure monitoring system can al ­
so stop working when there is an ESC mal­
function.
Tires and wheels
-Using snow chains may result in a system
ma lfunction.
- The tires with the identification "AO" or
"RO"
c::> page 260 have been matched with
your Audi tire pressure monitoring system .
We recommend that you use these tires.
- The tire pressure monitoring system can on­
ly monitor the tire pressure of the driving
tires. Check the tire pressure of the spare
wheel in the luggage compartment so that if necessary it is ready for use.
Storing tire pressures
Applies to vehicles: with tire pressure mon itor ing system
A change in tire pressure or a change in tires
must be stored in the system.
The tire pressure is stored in the MMI.
.,. Make sure befo re storing that the tire pressures
of all four tires meet the specified va lues and
are adapted to the load. Otherwise the system
could malfunction
c::> page 263.
.. Switch on the ign ition.
.,.. Select: the I MENU I button> Car> Systems "
control button > Service & control > Tire pres­
sure monitor > Store tire pressure > Yes, store
now .
(D Tips
Do not store the tire pressures if snow chains
a re installed . Otherwise the system could
malfunction.
273

Care and cleaning
Care and cleaning
General information
Regular, prope r care helps to maintain your vehi ­
cle's value.
It can a lso be a requirement when
submitting war ranty claims for cor rosion damage
and pa int defects on the body.
The necessary care prod ucts can be obtained
from an autho rized Audi deale r or authorized
Aud i Service Facility. Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Using clean ing and care products incorrectly
can be dangero us to your hea lth .
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
so ning .
@ For the sake of the environment
- Preferably use environmentally-friendly
products when buying cleaning agents.
- Do not dispose of leftove r clean ing and care
products with household t rash.
Car washes
The longer that deposits s uch as insects, bird
droppings, tree sap or road salt remain on the ve­ h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
i n crease the damag ing effect .
Before washing, r inse off heavy deposits with
p lenty of water.
St ubb orn deposits such as bird droppings or tree
sap are best removed with plenty of wate r and a
microfiber cloth.
Also, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icles with a pressure
washer, always follow t he ope ra ti ng ins tructions
p rovided w ith the pressure washer. This is espe­
cially important in regard to the pressure and
spraying distance . Do not aim the spray directly
274
at seals on side windows, doors, the hood, the
lug gage compartment lid or the sunroof* or at
t ir es, rubbe r hoses, insulating material, sensors*
or camera lenses*. Keep a distance of at least 16
i nches (40 cm).
Plug -in hybrid drive*: also do not direct the spray
at the charg ing unit in the rad iator g rille or at the
charg ing dock*.
Do not remove snow and ice with a pressure
washer.
Neve r use rot ary no zzles or high pressure noz­
z les.
The wate r temperatu re must not be above 140 °F
(60 °() .
Automatic car washes
Spray off the veh icle before washing.
Make sure that the windows and roof* are closed
and the windshie ld wipers are off. Follow instruc ­
tions from the car wash operato r, especially if
there are accesso ries attached to your vehicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the ve hicle starting from the top and work­
i ng down using a soft sponge or clea ning brus h.
Use solvent-free cleaning products.
Washing vehicles with matte finish paint by
hand
To avo id damaging the paint w hen washing, fi rst
remove dust and large pa rticles from your vehi­
cle. Insects, grease spots and f ingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply t he product using a microf iber cloth. To
avo id damaging the paint surface, do not use too
much pressure.
Rinse the ve hicle thoroughly with wate r. Then
clean using a neutra l shampoo and a soft micro ­
fiber clot h.
Rinse the vehicle thorough ly again and le t i t air
dry. Remove any water residue using a sham my. ..,..

Care and cleaning
Component Situation Solution
Paint
Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint¢
page 301
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have
it removed by an authorized Audi dea ler or a uthor-
ized A udi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately wi th a mild soap solution al and a
taminants such as
soft cloth
cosmetics or sunblock
Carbon parts Deposits clean the same way as painted parts¢ page 2 74
Decorative decals Deposits Soft sponge with a mild soap solutional
Audi e-tron Deposits Dry towe l
charging system *
Charging dock*
Deposits Soft towel with alcoho l-free cleaning so lution
a} Mild soa p sol ution: maxim um two tablespoons of neutral soap in 1 quart (I liter) of water
Internal cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap solutional
Trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap so lution al, detergent-free p lastic clean ing solu-
tion, if necessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a mild soap solutional
Safety belts Deposi ts Mild soap solution al, allow to dry before letting them re-
tract
276