jack points AUDI A3 2020 Owner´s Manual

8V2012721BK
Emergency assistance


» Wind the jack up further until the flat tire — Do not raise the vehicle until you are sure
comes off the ground > A\. the jack is securely engaged.
— Passengers must not remain in the vehicle
when it is jacked up.
— Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
Position the vehicle jack only under the designat-
ed lifting points on the sill > fig. 271. There is ex-
actly one location for each wheel. The jack must
not be positioned at any other location > AS ©.


An unstable surface under the jack can cause the — Make sure jack position is correct, adjust
vehicle to slip off the jack. Always provide a firm as necessary and then continue to raise
base for the jack on the ground. If necessary the jack.
place a sturdy board or similar support under the
jack. On hard, slippery surfaces (such as tiles) @) Note
use a rubber mat or similar to prevent the jack
from slipping owl, Do not Lift the vehicle by the sill. Position the
vehicle jack only at the designated lifting
A WARNING points on the sill. Otherwise, your vehicle will
be damaged.

— You or your passengers could be injured
while changing a wheel if you do not follow
Peon es imteen ene: Taking the wheel off/installing the spare
— Position the vehicle jack only at the desig- Follow these instructions step-by-step for chang-
nated lifting points and align the jack. ing the wheel.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi-
cient hold on the vehicle.
— A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
— On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
— Only raise your vehicle with the vehicle
jack provided by the factory. If you use a
vehicle jack for another vehicle, your vehi-
cle can slide and cause injury.
— Changes in load can affect the height of
the vehicle.
— Never start the engine when the vehicle is
raised, which could cause an accident.
— Support the vehicle securely with appro-
priate stands if work is to be performed
underneath the vehicle; otherwise, there is
a potential risk for injury.
—To help prevent injury to yourself and your
passengers:
2 R + 4
0 a

Fig. 273 Changing a wheel: using the screwdriver handle
(with the blade removed) to turn the bolts
6 &
Tt
“ oO oO

~
Fig. 274 Changing a wheel: alignment pin inside the top
hole

After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re-
place the wheel as follows:


355

8V2012721BK
Emergency situations

Loading the vehicle onto a flatbed truck

BaV-0402
|
a


Fig. 289 Vehicle on flatbed truck (example)
Front hook up
> Align the vehicle with the centerline of the car
carrier ramp.
> Attach the winch hook to the front towline eye
previously installed.
Rear hook up
> Align the vehicle with the centerline of the car
carrier ramp.
> Attach the winch hook to the rear towline eye
previously installed.
@) Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting
points illustrated.
oO S zt 6
> a a


Fig. 290 Front lifting point (example)
= Ss z
ba > i} oO
/


Fig. 291 Rear lifting point (example)
> Read and heed WARNING © A\.
> Locate lifting points > fig. 290 and > fig. 291.
> Adjust lifting arms of workshop hoist or floor
jack to match vehicle lifting points.
> Insert a rubber pad between the floor jack/
workshop hoist and the Lifting points.
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose.
Front lifting point
The lifting point is located on the floor pan rein-
forcement about at the same level as the jack
mounting point > fig. 290. Do not lift the vehi-
cle at the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vertical rein-
forcement of the lower sill for the on-board jack
> fig. 291.
Lifting with vehicle jack
Refer to > page 354.

Z\ WARNING
—To reduce the risk of serious injury and vehi-
cle damage.
— Always lift the vehicle only at the special
workshop hoist and floor jack lift points il-
lustrated > fig. 290 and > fig. 291.
— Failure to lift the vehicle at these points
could cause the vehicle to tilt or fall from a
lift if there is a change in vehicle weight
distribution and balance. This might hap-
pen, for example, when heavy components |>


369

Emergency situations


such as the engine block or transmission
are removed.
— When removing heavy components like
these, anchor vehicle to hoist or add corre-
sponding weights to maintain the center of
gravity. Otherwise, the vehicle might tilt or
slip
off the hoist, causing serious personal
injury.

@ Note
— Be aware of the following points before Lift-
ing the vehicle:
— The vehicle should never be lifted or
jacked up from underneath the engine oil
pan, the transmission housing, the front
or rear axle or the body side members.
This could lead to serious damage.
—To avoid damage to the underbody or
chassis frame, a rubber pad must be in-
serted between the floor jack and the lift
points.
— Before driving over a workshop hoist,
check that the vehicle weight does not
exceed the permissible lifting capacity of
the hoist.
— Before driving over a workshop hoist, en-
sure that there is sufficient clearance be-
tween the hoist and low parts of the ve-
hicle.
370