change wheel AUDI A3 CABRIOLET 2015 User Guide

M N
" > co ...... \!) 1.1'1
...... 1.1'1 ......
If you wish to improve comfort
when operating the vehicle at
normal load (up to 3 occu­
pants), you can adjust tire
pressures to those specified
for normal vehicle load. Before
operating the vehicle at maxi­ mum load, you must increase
the tire pressures to those
specified for maximum vehicle
load
c> .&. .
Bear in mind that the tire pres­
sure monitoring system can on­
ly monitor the tire pressures
you have stored. The system does not recognize the load
condition of your vehicle.
The effectiveness of the tire pressure monitoring system
will be impaired if you store normal load pressures but then
operate the vehicle at its maxi­
mum load
c> .&. .
Tires and wheels 237
See the illustration c> fig. 172
for the location of the label on
driver's side B-pillar (color of
the actual label and exact loca­
tion on the vehicle will vary slightly).
Note that the following table is
accurate at the time of going to
press and is subject to change.
In the event of discrepancies,
the tire pressure label is locat­ ed on the driver's side B-pillar
always takes precedence.
The table below lists the rec­ ommended cold tire inflation pressures for the Audi model
covered by your Owner's Litera­
ture at the vehicle's capacity
weight and the tire sizes instal­
led on the respective models as
original equipment, or as a fac-
tory option. ..,.
' •
•
' •

238 Tires and wheels
Model/ Tire designation Tire pressure
Engine normal load condition full load condition
front
rear front rear
PSI kPA PSI kPA PSI kPA PSI kPA
A3 Cab -225/45 Rl 7 91 Y
30 210 28 190 36 250 36 250 riolet : High Performance
1.8 liter 225/40 R18 92Y XL
4-cylinder High Performance
35 240 32 220 36 250 36 250
225/45 Rl7 91H
33 230
30 2
10
38 260
38 260 All Season
225/40 R18 92H XL
36 250 33 230 41 280 280 All Season 41
235/35 Rl9 91 Y XL
33 230 29 200 36 250 36 250 High Performance
A3 Cab- 225/45 Rl 7 91 Y
30 210 28 190 38 260 38 260 riolet: High Performance
2.0 liter
225/40 Rl8 92Y XL
4-cylinder High Performance
35 240 32 220 38 260 38 260
225/45 R17 91H
33 230 30 210 39
270
39 270 All Season
225/40 R18 92H XL
38 260 35 240 41 280 41
280
All Season
235/35 R19 91 Y XL
35 240 29 200 38 260 38 260 High Performance
XL= reinforced or extra load tire. It may also appear as xi, EXTRA LOAD, or RF on the tire side-
wall.
The correct tire pressure for the
spare wheel is located on a la­
bel on the driver's side B-pillar.
Because technical changes may
be made to vehicle equipment
during the model year, always
compare the tire size designa­
tion on the tire pressure label on your vehicle with the tires on
your vehicle. Make sure that the tire size information on the ve­
hicle label is the same as the
size of the tires on the vehicle. This is
especially important if
the vehicle belongs to someone else or you bought the vehicle
with different rims/tires or you bought the vehicle as a previ­
ously owned vehicle.
Remember, your safety and
that of your passengers also de­ pends on making sure that load
limits are not exceeded. Vehicle
load includes everybody and ev­
erything in and on the vehicle.
These load limits are

M N
" > co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
tire failure and loss of
control.
-Excessive speed and/over­ loading can cause heat
build -up, sudden tire failure
and loss of control.
-If the tire pressure is too low or too high, the tires
will wear prematurely and
the vehicle will not handle
well.
-If the tire is not flat and you do not have to change a
wheel immediately, drive at
reduced speed to the near­
est service station to check
the tire pressure and add air as required.
(D Note
Driving without valve stem
caps can cause damage to
the tire valves. To prevent
this, always make sure that
factory installed valve stem caps on all wheels are secure­
ly mounted on the valve.
@ For the sake of the environment
Underinflated tires will also
increase the fuel consump­
tion.
Tires and wheels 243
Tires and vehicle load limits
'
There are limits to the amount of load or weight that any vehi­
cle and any tire can carry. Ave­
hicle that is overloaded will not
handle well and is more diffi­
cult to stop. Overloading can
not only lead to loss of vehicle
control, but can also damage important parts of the vehicle
and can lead to sudden tire fail­
ure, including a blowout and
sudden deflation that can cause
the vehicle to crash.
Your safety and that of your passengers also depends on
making sure that load limits are
not exceeded. Vehicle load in­
cludes everybody and every­
thing in and on the vehicle .
These load limits are technical­ ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR").
The "GVWR" includes the
weight of the basic vehicle, all
factory installed accessories, a
full tank of fuel, oil, coolant and other fluids plus maximum ""
' •
•
' •

M N
" > co ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
reached the level to trigger illumination of the
TPMS low tire pressure telltale.
Your veh icle has also been equ ipped with a
TPMS malfunction indicato r to indica te when
the system is not operating properly . The
TPMS malfunction indicator is combined with
the low tire pressure tellta le . When the sys­
tem detects a malfunct ion, the telltale will
flash for approximately one minute and then
remain cont inuous ly illuminated. This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists .
When the malfunct ion indicator is illuminat­
ed, the system may not be able to detect or
sig nal low t ire pressure as intended . TPMS
malfunct ions may occur for a variety of rea­
sons, including the installa tio n of replace­
ment or a lternate tires or whee ls on the veh i­
cle that prevent the TPMS from funct ion ing
properly. Always check the TPMS malfunction
tellta le after replacing one or more tires or
wheels on your veh icle to ensure that the re­
placement or alternate tires and wheels allow
the TPMS to continue to function properly.
If the Tire Pressure Monitoring System
indicator appears
Applies to vehicles: with tire pressure monito ring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction .
Fig . 177 In strum ent clus te r: indica tor l igh t w ith mes ­
sage
Using the ABS sensors, the tire pressure moni­
toring system compares the t ire tread circum­
ference and vibration characteristics of the in­
d iv idual tires . If the pressure changes in one
Tire s an d wheel s 259
or more tires, this is indicated in the instru­
ment cluster disp lay with an indicator light
ti] and a message c:::> fig . 177. If only one tire
is affected, the locat ion of that tire will be in­
dicated. The message turns off after a few mi­
nutes . You can d isplay the message aga in
c:::> page 2 8 .
The tire pressures must be stored in the menu
display again each time the pressures change
(sw itching between partial and full load pres ­
sure) or after chang ing or replacing a t ire on
your vehicle
c:::> page 260 . The t ire press ure
monitori ng system only monito rs the tire
pressure yo u have stored . Yo u can find the rec ­
ommended t ire press ures for your vehicle on
the labe l on the driver 's doo r pillar
c:::> page235 .
Tire t read circumference and vib rat ion charac­
teristics can change and cause a tire pressu re
warning if :
- I f the tire pressure in one or mo re tires is
t oo low,
- the t ire has structural damage,
-The tire was replaced or the t ire p ressure
changed and it was not stored again
c:::> page 260 .
-The spare tire is installed .
Indicator light s
ti]-Loss of pressure in at least one tire c:::> &.
Check the tires and replace or repair if neces­
sary. Check/correct the pressures of all four
tires . Then store the t ire pressures in the MMI
c:::> page 2 60 .
DI (T ire Pressure Monitoring System) T ir e
press ure: S ystem malfunct ion!. If Ill ap­
pears afte r switching the ignition on or while
driv ing and the
ti] indicator l ight in the in­
str ume nt cluster b links for app rox imately one
minute and then stays on , the re is system
malfunction. Try to s to re the co rrec t ti re pres­
s u res
c:::> page 260. If the indicator light does
turn off or tu rns on again after a short period
of time, drive to yo ur authorized Aud i dea ler
or qualified repa ir facility immed iate ly to have
the malfunction corrected. .,..
•
•
•

260 Tire s and wheel s
& WARNING
-If the tire pressure warning light ti] in
the instrument cluster turns on, the
pressure in one or more tires is too low.
Reduce the vehicle speed immediately
and avoid any hard steering or braking
maneuvers . Stop as soon as possible,
check the t ire and inflate the tire to the
correct pressure, which is specified on
the tire pressu re labe l on the veh icle
<:?page 235. Driving with a t ire with low
pressure causes the tire to overheat and
can res ult in failure of the tire . Low pres ­
sure can a lso have a negat ive effect on
the driving and braking behavior of the
vehicle.
- The driver is responsible for maintaining
the correct tire pressures. You must
check the t ire pressures regularly.
- Under certain cond itions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be de layed .
- Ask your author ized dealer if r un-flat
t ires may be used on your vehicle.
- The tire pressure monitoring system can
also stop work ing when there is an ESC
malfunction.
- Using snow chains may result in a system
malfunction.
- The tires with the ident ificat ion "AO" or
"RO" ¢ page 248 have been matched
with your A udi tire pressure monitoring
system. We recommend that you use
these tires.
- The tire pressure monitoring system can
on ly mon itor the t ire pressure of the
driving tires . Check the tire pressu re of
the spa re wheel in the luggage com part­
ment so tha t if ne cessary i t is ready for
u se.
-
Storing tire pressures
Applies to vehicles: wit h tire press ure mo nitor ing system
A change in tire pressure or a change in tires
must be stored in the system.
The tire pressure is stored in the MMI.
.. Ma ke s ure before storing that the ti re pres ­
sures of a ll four tires meet the specified va l­
ues and are adapted to the load. Otherwise
the system could malfunction
¢ page 235.
.. Switch t he ignit ion on.
.. Select: the
I MENU I button > Car > Systems *
contro l butto n > Service & control > Tire
pre ssure monitor > Store tire pre ssure >
Yes , st ore n ow .
(D Tips
Do not store the tire pressures if snow
cha ins a re i nstalled. O therw ise the system
could m alfun ction.

the tire chain before mounting the wheel
and tire is recommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard braking or in an accident.
Never store the inf latab le spare tire or
jack and tools in the passenger compart­
ment.
- Normal summer or winter tires must not
be mounted on the compact spare wheel
rim.
Removing the subwoofer
A pp lies to vehicles: with s ubwoofer
The subwoofer must be removed before the
spare wheel* can be removed.
Fig. 182 Spare wheel well: subwoofer
Removing the subwoofer
• Lift the cargo floor c:, page 262, fig. 180.
• Pull the latch (D c:> fig. 182 toward the ca­
ble.
• Press the locking tab @down .
• Remove the connector @ and set the re-
moved cable aside.
• Remove the bolt@.
• Carefully remove the subwoofer.
Installing the subwoofer
• Carefully place the subwoofer n the rim
well. The word "FRONT" on the subwoofer
must face forward .
• Insert the connector that was removed .
• Secure the subwoofer with the bolt.
~ • Fold the cargo floor cover back into place.
r--. > co
rl I.O
"' rl
"' rl
What do I do now? 263
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel.
• After you experience a tire failure, pull the
car well away from moving traffic and try to
reach
level ground before you stop c:> _&..
• All passengers should leave the car and
move to a safe location (for instance, behind
the guardrail)
c:> _&..
• Engage the parking brake to prevent your
vehicle from rolling unintentionally
c:> _&. .
• Move selector lever to position P c:> ,&..
• If you are towing a trailer, unhitch the trailer
from your vehicle.
• Take the
jack c:, page 261 and the spare tire
r:> page 262 out of the luggage compart­
ment .
A WARNING
You or your passengers could be injured
while changing a wheel if you do not fol­
low these safety precautions:
-If you have a flat tire, move a safe dis­
tance off the road. Turn off the engine,
turn the eme rgency flashers on and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To help prevent the vehicle from moving
suddenly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed. When one
front wheel is lifted off the ground, plac­ ing the Automatic Transmission in P
(Park) will
not prevent the vehicle from
mov ing .
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
-

264 What do I do now?
-Always store the vehicle tool kit, the jack
and the replaced tir e in the luggage com­
partment ¢
page 132.
Changing a wheel
When you change o wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Remove the decorative wheel cover*. For
more details see also¢
page 264, Deco­
rative wheel covers
or ¢ page 265,
Wheels with wheel bolt caps.
2 . Loosen the wheel bolts¢ page 265 .
3. Locate the proper mount ing point for the
jack and align the jack below that point
¢page 266.
4. Raise the car with the jack ¢ page 266.
5. Remove the
wheel with the flat tire and
then install
the spare ¢ page 267.
6. Tighten all wheel bolts lightly.
7 .
Lowe r the vehicle with the jack.
8 . Use the wheel bolt wrench and
firmly
tighten all whee l bolts c::> page 265.
9. Replace the decorative wheel cover*.
A WARNING
Always read and follow all WARNINGS and
information
c::> .&. in Raising the vehicle on
page
266 and c::> page 268.
After changing a wheel
A wheel change is not complete without the
doing the following .
• Always store the vehicle tool kit, the jack*
and the replaced tir e in the luggage com­
partment ~
page 132 .
• Check the tire pressure on the spare wheel
i mmediately after mount ing it.
• As soon as possible, have the
tightening
torques
on a ll wheel bo lts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as poss i­
ble.
(D Tips
- If you notice that the wheel bolts a re
corroded and difficult to turn while
chang ing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
- After changing a whee l, the tire pressure
in all four tires must be checked/correct­
ed and the tire pressure monitoring indi­
cator must be stored in the MMI
c::>page260.
Decorative wheel covers
Applies to vehicles: wit h decorative whee l covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 183 Chang ing a wheel : Remov ing th e w heel cover
Removing
.,. Insert the hook (provided with the vehicle
tool kit) in the hole in the whee l hub cover .
.,. Pull
off the decorative wheel cover
c::>fig.183.

266 What do I do n ow ?
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed .
Fig. 186 Sill panels: mark ings
Fig. 187 Sill : posit ion ing the veh icle jack
., Engage the pa rkin g brak e to prevent your
vehicle from rolling un intentionally.
., Move the
se lect or l ever to po siti on P .
., Find the marking (imprint) on the sill that is
nearest the wheel that wi ll be changed
r::> fig. 186. Behind the marking, there is a
lifting po int on the sill for the vehicle jack.
., Vehicles with a sill : Note the position of the
s ill when pos itioning the vehicle jack
¢ fig . 187 .
., Place the vehicle jack (vehicle tool kit) on a
firm su rface. Use a flat, stab le support if
necessary. On a slippe ry surface such as tile,
you should use a non-slip pad (such as a rub­
ber mat)
c::> A .
., Turn the vehicle jack located under the lift­
ing point on the sill to raise the jack until its
arm @r=>
fig. 187 is located under the des­
ignated plastic mount
c> A, r=>@ .
., Align the jack so that its arm@r=> fig. 187
engages in the designated lifting point in
the door sill and the movable base @ lies
flat on the gro und . T he base @ must be
ver­
tical
under the lift ing po int @ . .,
Wind the jack up fu rther until the f lat tire
comes off the ground
r=> A.
Position t he vehicle jack only under the desig ­
nated lifting points on the si ll
¢fig. 186.
There is exactly one location for each wheel.
The jack must not be positioned at any other
location
r=> ,&. r=>Q).
An un sta ble surf ace under the jack can cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or similar support
under the jack. On
hard, sl ipp ery su rfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c> ,&. .
A WARNING ~
-You or your passengers could be injured
while changing a wheel if you do not fo l­
low these safety preca utio ns:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle .
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessa ry,
use a stu rdy board under the jack.
- On hard, slippery surface (such as t iles)
use a rubber mat or simi lar to prevent
the jack from slipping.
- Only raise your vehicle with the vehicle
jack provided by the fac to ry.
If you use
a vehi cle jack for another vehicle, your
vehicle can slide and cause injury.
- Changes in temperat ure or load can af­
fect the height o f the veh icle .
- Never start the engine when the vehi­ cle is raised, which co uld cause an acc i­
dent.
- Suppo rt the ve hicle securely with ap­
propr iate s tands if work is to be per­
formed underneath the vehicle; other ­
wise, there is a potential risk for in jury . .,.

....,
N
r--. > co
rl I.O
"' rl
"' rl
-To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is secu rely engaged.
- Passengers must not remain in the ve­
h icle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and t raffic.
- M ake sure jack position is correct, ad­
just as necessary and then conti nue to
ra ise the jack .
- Changes i n temperature or load can af­
fect the height of the ve hicl e.
CD Note
Do not lift the vehicle by the sill. Pos ition
the vehicle jack only at the des ignated lift­
ing points o n the sill. Othe rwise, your vehi­
cle will be damaged.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fi g. 188 Changing a wheel: using the screwdriver han ­
dle (with th e blade re moved} to turn the bolts
F ig . 189 Changing a wheel: alignment pin inside th e
top hole
What do I d o now ? 267
After you have loosened all wheel bo lts and
raised the vehicle off the grou nd, remove and
replace the wheel as follows:
Removing the wheel
.,. Use the hexag onal socket in the scr ewdriv ­
er handle
to completely remove the top ­
most wheel bolt and set it aside on a
clean
surface c:> fig. 188.
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
c:> fig. 189.
.,. Then remove the other wheel bolts as de­
scribed above.
.,. Tak e off the whee l leaving the a lignment pin
in the bo lt ho le
c:> (D .
Putting on the compact spare wheel
.,. Lift the spare wheel and carefully s lide it
over the alignment pin to guide it in place
c:>(D .
.,. Use the hexagona l socket in the screwdriver
handle to screw in and tig hten all whee l
bolts
slightly.
.,. Remove the a lignment pin and inse rt and
tighten the rema ining whee l bolt slightly
Like the rest .
.,. Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts f irmly
c:> page 265 . Tighten
them
crosswise, from o ne bolt to the (ap­
proxima tely) oppo site one, to keep the
wheel cente red.
CD Note
When remov ing or i nsta lling the whee l,
the r im cou ld hit the b rake roto r and dam­
age the ro tor. Wor k carefu lly and have a
second pe rson help you.
(D Tips
Neve r use the hexagonal socket in the han­
d le of the screwdriver to loosen or tighten
the wheel bo lts .
llll-

268 What do I do no w?
-Pull the reversible blade from the screw ­
driver before you use the hexagonal
socket in the handle to t urn the whee l
bo lts.
- When mounting tires with
unid ire ctional
t re ad design
make s ure the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to turn. Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the hub. Remove all dirt from these
surfaces before remount ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern
int ended fo r use in a specific dir ection
When us ing a spare tire w ith a tread pattern
i ntended for use in a specific direction, please
note t he following:
- The direction of rotation is marked by an ar ­
row on the side of the tire .
-If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the t ire will not be able to
achieve its optimum perfo rma nce character­
ist ics with rega rd to aquaplaning, noise and
wea r.
- We recommend that you pay particular at­
tent ion to this fact du ring wet weat her and
that you adjust your speed to match road
condit ions .
- Replace the fla t tire w ith a new one and
have it ins talled on your veh icle as soon as
possible to restore the handling advantages
of a unidirectiona l tire .
Notes on wheel changing
Please read the information ¢ page 248, New
tires and replacing tires and wheels
i f you are
go ing to use a spare t ire which is d ifferent
from the tires on your veh icle . After you change a tire:
-
Ch eck the tire pr essure on th e spar e imm e­
diatel y after in stallation .
- Hav e th e whe el bolt tight ening torque
c h ec ked with a torque wr ench as soon as
po ssible by your author ized Audi de aler or
a qu alified servic e sta tion.
- With ste el and alloy wheel r im s, the wheel
bolt s ar e c orre ctl y tightened at a torque of
9 0 ft lb (120 Nm ).
- If you notice th at the wheel b olt s ar e co r­
rod ed and diffi cult to turn w hile changing
a tire , the y should be repl aced before you
check the t ightening to rque.
- Repl ace the flat tire with a new o ne and
ha ve it in stalled on your vehicle as soon a s
possible. Remount the wheel cov er.
Until then , dri ve with extra care and at re­
duc ed sp eed s.
A WARNING
-
- If you are going to equip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information
¢ page 248,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment.
- In an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.
- Always sto re damaged wheel , jack and
too ls se curely in the luggage compart­
men t. Otherwise, in an accident or s ud­
den maneuve r they could f ly forwa rd,
causing injury to passengers in the vehi­
cle.