instrument cluster AUDI A3 CABRIOLET 2016 User Guide

<( co ..... N
" N ..... 0 r--. > 00
Shifting manually (tiptronic mode)
Applies to: vehicles with automatic transmissions
The tiptronic allows the driver to shift the gears
manually.
Fig . 82 Center conso le: manua l shifting with the selector
lever
Fig. 83 Steering wheel: manual sh ifting with the shift pad·
dles*
Shifting with th e select or lever
You can sh ift into tiptron ic mode while stationary
and while driv ing.
• To sh ift into tiptronic mode, push the selector
lever from the D/S sett ing to the right in the
tiptronic shift gate. Once the transmission has
switched modes, the se lector lever posi tion
M
is shown in the instrument cluster display
r:::>page 76, fig. 79. For example M4, means the
fourth gear is engaged.
• To shift up a gear, tap the selector lever for­
ward
0 r:::> fig. 82.
• To shift down a gear, tap the selector lever to
back
a .
Shifting with the sh ift padd le s*
You can operate the shift padd les in the D/S or M
(tiptronic shift gate) selector lever positions.
Aut oma tic tr ansm iss ion
• To shift up one gear, tap the shift paddle 0
r:::> fig. 83.
• To shift down one gear, tap the shift paddle Q.
If the shift paddles are tapped while in the D/S
selector lever position, automatic mode switches
off briefly. To switch from manually shifting back
to automatic shifting immed iately, tap the sh ift
paddle
0 ¢ fig. 83 for 1 second.
T o keep shifting using the shift padd les, move
the selector lever to the rig ht out of the D/S posi­
t ion into the tiptronic shift gate .
T he transmission automatically shifts up or down
before critica l engine speed is reached.
T he transmission only allows manua l shifting
whe n the eng ine speed is w it hi n the pe rmitted
ra nge.
(0 Tips
- If you shift to the next lowest gear, the
transmission will only shift if the eng ine will
not be over -revved .
- With k ick-down, the t ransmiss ion shifts to a
lower gear, depending on vehi cle speed and
engine speed.
- tiptronic does not work if the transmission
is running in emergency mode.
Kick-down
Applies to: vehicles with automatic transmissions
Kick-down enables maximum acceleration.
When you press the accelerator pedal down be­
yond the res istance point, the automatic trans­
mission downsh ifts into a lower gear, depending
o n veh icle speed and engine RPM.
It shifts up in ­
to the next higher gear once the maxim um speci­
fied eng ine RPM is reached.
A WARNING ~
P lease note that the wheels cou ld spin on
slick or slippery roads when kick-down is ac­
tive.
-
81

Automatic transmissio n
Launch Control-Program
Applies to: vehicles with Launch Control
The Launch Control Program enables maximum
acceleration .
Requirement: the engine must be at operating
temperature and the steer ing wheel must not be
turned .
.,. With the engine runn ing, press the
i ,; OFF ! but­
ton br iefly one time
l) .
"' Pull the selector lever back out of the 0/5 posi­
tion briefly to select the 5 posit ion, or press it
toward the rig ht into the tiptronic pos ition or
select the
Dynami c driving mode in d rive se­
lect*
~ page 106.
"' Press the b rake pedal firmly with your left foot
and hold it all the way down for at least 1 sec ­
ond.
"' At the same time, press the gas pedal a ll the
way down w ith your right foot unti l the engine
reaches and stays at a high RPM level.
"' Remove your left foot from the brake.
_.&. WARNING
-Always adapt you r driv ing to the traffic flow .
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by your d riv­
ing and the vehicle's a cce le ration.
- Please note that the dr ive wheels can sp in
and the vehicle can break away when sport
mode is switched on, especia lly when the
road is s lippery.
- Once the vehi cle has sta rted moving, press
the
l .!'3 OFF ! button briefly to tu rn the sport
mode off.
(D Tips
- The t ransmiss ion temperature may increase
significantly after using t he launch control
program.
If tha t happens, the p rogram may
l ) In vehicles with a driver info rma tion system, an ESC light
i n the in st rument cl uste r stays on cont inuous ly and t he
message Sta bilization co ntrol (ES C): sport . Warning! Re ­
st ricted stab il ity app ears temp orar ily .
82
not be avai lab le for a few minutes. It will be
available again after a coo l-down period.
- When accelerating using the launch contro l
program, all vehicle parts are s ubject to
heavy loads. This can lead to increased
wear .
Emergency mode
App lies to: vehicles with auto matic transmissions
In the event of a system malfunction, there is an
emergency program.
If all of the selector lever positions are hig hlight­
ed with a light background in the instrument
cluster disp lay, there is a system malfunction and
the 5 tronic transmission is running in the emer­
gency program. The veh icle can still be driven in
emergency mode, but only with reduced speed
and not in all gears . In some cases, the vehicle
cannot dri ve in rever se .
(D Note
If the transmission runs in emergency mode,
drive to an authorized A udi dealer or author­
ized Audi Se rvice Facility immed iate ly to have
the malfunct ion corrected.
Transmission malfunction
• Tran smi ssion malfun ction ! Pl ea se stop the
vehicle and sele ct P
There is a ma lfunction in the transm ission . Park
the ve hicle secure ly and do not cont inue driving.
See an author ized Audi dealer or authorized A udi
Se rvice Facility for assistance.
• Tran smi ssion overheating! Pleas e stop the
v e hicle!
The transmission is too hot and can become dam ­
aged . Stop and let the transmiss ion cool w ith the
engine r unning (at idle) in the P se lector lever po­
s it ion. Then the ind icator light and the message ..,.

<( co ..... N
" N ..... 0 r--. > 00
-Please note that unconsciously "resting"
your foot on the accelerator pedal prevents the cruise control from braking. This is be­
cause pressing the accelerator pedal over­
rides the cruise control system .
-If there is a brake system malfunction such
as overheating when the speed warning sys­
tem is switched on, the braking function in
the system will be deactivated. The remain­
ing speed warning system functions will re­
main active , as long as the~ (USA mod­
els) /
fil (Canada models) indicator light is
on.
{i) Tips
- The cruise control system is ideal for
stretches with speed limits. The driver is re­
sponsible for adhering to the correct speed.
- The cruise control remains active when
shifting gears.
- The brake lights turn on when the brakes
are activated.
Switching on
A pp lies to: ve hicles with c ru ise control system
0
f
®t
0
Fig. 86 Operat ing lever: c ru ise control syste m
.. To switch the cruise control on, pull the lever
into position @~
fig. 86 .
.. Drive at the speed to be maintained .
.. To store the speed, press the button @. The
@;\1)~14 indicator light (USA models)/ fil (Cana­
da models) turns on in the instrument cluster.
Assist
Changing speed
Applies to : vehicles wit h cruise co ntrol sys tem
., To increase or decrease the speed in incre­
ments,
tap the lever in the 010 direction
~ page 89, fig. 86.
.. To increase or decrease the speed quickly, hold
the lever in the 0 / 0 direction until the de­
sired speed is reached.
Overriding the speed
You can press the acce lerator pedal down to in­
crease your speed, for example if you want to
pass someone. The speed you saved earlier will
resume as soon as you let off of the accelerator
pedal.
If, however, you exceed your saved speed by 5
mph (10 km/h) for longer than 6 minutes, the
cruise control turns off temporarily .
The@;\!)~14
(USA models) ;fil (Canada models) indicator
light in the instrument cluster turns off and the
stored speed is maintained.
Preselecting the speed
Appl ies to: vehicles wi th cruise co ntrol sys te m
You can pre-select your desired speed while the
vehicle is not moving.
., Switch on the ignition .
.. Pull the lever into position
(D 9 page 89,
fig. 86 .
.. To increase or decrease the speed, tap the lever
in the
0 10 direction.
This function makes it possible, for example, to
save the speed you want before driving on the
highway. Once on the highway, activate the
cruise control system by pulling the lever toward
the position
(D .
Switching off
Applies to : vehicles wi th cruise co ntrol syste m
Temporary deactivation
.. Press the brake pedal, or
.. Press the lever into position @ (not clicked into
place)
~ page 89, fig. 86, or ..,
89

Ass is t
(D Note
The sensor can be displaced by impacts or
damage to the bumper, whee l housing and
underbody. The adaptive cruise control and
pre sense front may become impa ired as a re­
sult . Have an authorized Audi dealer or au­
thorized Audi Service Fac il ity check their func­
tion.
In curves
Applies to: ve hicles w ith Aud i adapt ive cru ise co ntro l and Audi
pre se nse front
F ig . 89 Examp le: driv ing into a cu rve
When driving into a curve ¢ fig. 89 and out of a
curve, the adaptive cruise control may react to an
object in the neighboring lane and apply the
brakes . You can prevent that by pressing the ac­
celerator pedal briefly .
Stationary objects
Applies to: vehicles with Aud i adapt ive cruise co ntro l and Audi
p re se nse front
Fig . 90 Examp le : object changing lanes and stationary ob­
j ect
l ) Speed lim it s depend on t he country a nd the speedomete r.
92
Adaptive cruise cont rol
The adaptive cru ise con trol system only reac ts to
ob jects that are moving or t hat the system has
already detected as moving . For example, it can
react when a vehicle that has already been de­
tected @turns or changes lanes, but adaptive
cruise contro l does not react to a stationary vehi­
cle @. Press the brake pedal to slow the vehicle
down .
Pre sense front
Pre sense front only reacts to stat ionary objects
at low speeds .
Switching on/off
Applies to : vehicles wit h Audi adapt ive cruise control
Fig . 91 Operat ing lever: switch ing on and off
Fig . 92 Instrument cluster: adaptive cru ise contro l
You can set any speed l) between 20 mph and 95
mph (30 and 150 km/h) .
Ind icator lights and messages in the inst rument
cluster disp lay inform yo u about the curre nt sit -
uat ion and settings. .,.

Switching adaptive crui se control on
"' Pull the lever toward you into position @
¢
fig. 91. A CC: s tandby appea rs in the instru­
ment cluster disp lay .
Saving the speed and activating regulati on
"'T o save the c urrent speed , press the ISETI
¢ fig. 91 button . The stored speed is shown in
t h e tachomete r LED line @and appears briefly
in the information line ®¢
fig. 92 .
"' To activate the regulation whi le stationary, you
must press the brake pedal.
Sw itching adaptiv e cruise control off
"' Push the lever away from you into position @
until it clicks i nto place ¢
fig. 91 . The message
AC C: off appears.
The stored speed in the LED line is e rased.
@ Indicato r lights
II -adaptive cruise control is switched on. No
objects are detected ahead. The stored speed is
maintained.
• -An object a head was detected . The adaptive
cruise control system regulates the speed and
d istance to the object ahead and brakes/acce ler ­
ates automatica lly.
fij -adaptive cru ise control is switched on. An
object ahead was detected. Your vehicle remains
stopped and w ill not start driving automatica lly.
• -T he automatic bra king is no t enough to
maintain a sufficient distance to a n object ahead.
You must intervene ¢
page 96, Request for
driver intervention.
© Instrument cluster display
I f adaptive cruise control is not shown in the in­
s trument cluster disp lay, yo u can call it up using
the mu ltifunction steering wheel b uttons
¢ page 24.
Based on the g raph ics in the d isp lay, you can de­
termine if the system is m ainta ining a distance to
;;!; a vehicle ahead and what that distance to this ve-....
~ hide is: N ....
R No vehi cle -No object ahead was detected.
> 00
Assist
White vehicl e -An object ahead was de tected .
Red vehicl e -Request for the dr iver to take action
¢page 96.
Both
arrows on t he scal e@ indicate the d istance
to the object ahead . No arrow appears when the
vehicle is on an open road and t here is no object
ahead. If an object is detec ted ahead, the a rrow
moves on the sca le.
T he green zone o n the scale indicates the store
distance. For informat ion on changing the dis­
t a nce, refer to ¢
page 95. If the dis tance se ­
l ected is exceeded or not reached, the arrow
moves into the red zone on the scale.
A WARNING
- Using adaptive cruise control incorrectly can
cause collisions, other accidents and ser ious
in ju ries.
- If you press the
!SET ! button w hen driving at
speeds be low 20 mph (30 km/h), the vehi­
cle acce lerates automatically up to 20 mph
(30 km/h), wh ich is the minimum speed
that can be set.
{!) Tips
- If you switch the ignit ion or the adaptive
cruise control system off, the set speed is
erased for safety reason.
- The Elect ronic Stabilization Control (ESC)
and Anti-S lip Regulat ion (ASR) both sw itch
on when the adaptive cruise control is
switched on . ESC and ASR ca nnot be switch­
ed off when adapt ive cruise control is
switched on.
- With the adaptive cruise control act ivated
t he ESC spo rt mode cannot be activated.
93

Ass is t
Changing the speed
Applies to: vehicles with Aud i adapt ive cruise contro l
0
f
•
0
Fig. 93 Operat ing lever: changing the speed
.,. To increase or reduce the speed in increments,
tap the lever up or down.
.,. To increase or decrease the speed quickly,
hold
the leve r up or down until the red LED @ reach­
es the desired speed
¢ page 92, fig. 92.
After each change, the new stored speed appears briefly in the informat ion line ®¢
page 92,
fig. 92.
Driving in stop-and-go traffic
Applies to : vehicles with Aud i adapt ive cru ise control
The adaptive c ruise control system assists yo u in
stop-and-go traffic. If an object that is detected
ahead stops, your vehicle will brake and stay at a
stop, within the limits of the system.
Starting to drive with adaptive cruise
control!)
If your vehicle brakes to a stop because an object
is detected ahead,
AC C autom. go appears br iefly
in the instrument cluster display. Your vehicle is
in automatic start mode.
As long as the message
ACC au tom . go is dis­
p layed and the object detected ahead starts to
move, your vehicle will continue driving¢ ,&..
You can activate
AC C autom. go again for a short
time by pulling the lever to position @
¢ page 94, fig. 94.
The ACC autom . go start mode ends when the
b rake pedal is p ressed.
l ) Th is is not ava ilab le in some countr ies .
94
Criteria for switching off
The adaptive cru ise con trol switches off for s afe­
ty reasons when stationary:
- when the d river 's doo r is ope n,
- when the vehicle is stationary for more than 3
minutes,
- when the d river's safety belt is not fastened .
A WARNING
If the message ACC autom. go1> appears, the
vehicle continues driving, even if there is an
obstacle between your vehicle and the ob je ct
ahead. This increases the risk of an accident .
@ Tips
If adaptive cruise cont rol is act ive and your
vehicle does no t start driv ing even though the
message
AC C autom . go1> appears, you ca n
start by tapping the a cce le ra tor ped al.
- If an obstacle is detected when dr iving with
adaptive cruise cont rol, the system will re­
ques t you to beg in driving¢
page 96 . You
vehicle will begin dr iving more slowly. This
can also happen in situations where there is
no v is ible obstacle.
Interrupting cruise control
Applies to : vehicles with Audi adaptive cruise control
Fi g. 94 Operat ing lever
Requirement: adaptive cruise cont rol must be
switched on .

<( co .... N ,.__
N .... 0 ,.__
> co
Overriding cruise control
Ove rriding means ex ceeding the selected speed
when adaptive cruise control is active, for exam­
p le when pressing the accelerator peda l when
pass ing.
"'T o accelerate manua lly, p ull the lever toward
you into position @and ho ld it there . T he mes ­
sage
ACC : over ride appears . Or
"' press th e accelerator pedal.
"' To resume cruise control, release the lever or
take your foot off the acce lerator pedal.
Inte rrupting cruise contr ol w hil e driving
"'Move the lever into position @. The message
ACC: standb y appears. Or
"' press th e brake pedal.
"' To resume the stored speed, move the lever in­
to posit ion @.
Int errupting c rui se contr ol wh en stopped
"' Push the lever away from you into position @.
The message
ACC : stan dby appears.
"' To resume cruise control, press the brake pedal
and pull the lever toward you into position@.
A WARNING
It is dangerous to activate cruise control and
resume the stored speed when the current
road, traffic or weather conditions do not pe r­
m it this. This could result in a crash.
Setting the distance
App lies to: vehicles with Audi adaptive cruise control
F ig. 95 O perat ing leve r: sett ing the d ist an ce
"'Tap the switch to display the current set dis­
tance
c> fig . 95 .
Assist
"'To increase or reduce the d istance in incre­
ments, tap th e switch again to the right or left.
T he distance between the two veh icles will
change in the instrument cluster display.
When approaching an object detected ahead, the adaptive cruise contro l system brakes to match
that object's speed and then regul ates to the
stored distance. If the object detected ahead ac­ celerates, adaptive cruise contro l will also accel­
erate up to the stored speed .
The higher the speed, the greater the distance in meters
c> & . The Distance 3 setting is recom­
mended . That is equa l to the general recommen­
dation of "half t he speed shown on the speedom ­
eter ".
The distances provided are example values. De­ pending on the driv ing s ituation, the current
speed and the way the object detected ahead is
driv ing, the actual d ista nce may be more or less
t h an these target d istances .
o::::::::,_o::::::::, ___ Distance 1: th is sett ing corresponds
to a distance of 92 feet/ 28 meters when at a speed of 62 mph ( 100 km/h), for example (time
betwee n: 1 second).
o::::::::, __ o::::::::, __ Distanc e 2: this setting corresponds
to a distance of 118 feet/ 36 meters when at a speed of 62 mph ( 100 km/h), for example (time
betwee n: 1.3 seconds) .
o::::::::, ___ o::::::::,_ Distance 3: this setting corresponds
to a distance of 164 feet
I SO meters when at a
speed of 62 mph ( 100 km/h), for example (time
betwee n: 1.8 seconds) .
o::::::::, ____ o::::::::, Distance 4: this setting corresponds
to a distance of 219 feet
I 67 meters when at a
speed of 62 mph ( 100 km/h), for example (time
betwee n: 2.4 seconds) .
A WARNING
-Driving too close to other vehicles increa ses
the risk of collis ions an d serio us inju ries .
- Sett ing sho rt d istances to vehicles ahead re­
duces the dis tance an d time th at you have
to stop your vehicle safe ly . Th is increases
the need for you to pay attention to traffic . ..,.
95

<( co ..... N
" N ..... 0 r--. > 00
Switching on and off
App lies to: ve hicles with Audi active lane assist
Fig . 98 Turn signal lever: button for act ive lane assist
Fig. 99 Windshield: camera wind ow for active lane assist
... Press the c:> fig. 98 button to switch the system
on and off. The . or
Pl1 indicator light in the
instrument cluster turns on or off.
Indicator lights
• Ready: the indicator light turns on when the
system is ready for use. The system can now be
operated .
Pl1 Not ready: the indicator light turns on if the
system is switched on but is inoperable. This may
be due to the following reasons:
- There is no lane boundary line.
- Th e relevant lane marker lines are not detected
(for example, markings in a construction zone
or because they are obstructed by snow, dirt,
water or lighting).
- The vehicle speed is below the activation speed
of approximately 40 mph (65 km/h) (the speed
may vary depending on your country).
- The lane is narrower than approximately 8
ft
(2.5 m) or wider than approximately 18 ft
(5.5 m).
- The curve is too narrow.
Assist
-The driver's hands are not on the steering
wheel.
(D Tips
- Make sure the camera's field of view
¢ fig. 99 is not obstructed by stickers or
anything els e. For information on cleaning,
refer to
c:> page 224.
-Market-specific: in certain countries: if the
system is sw itched on, it will remain opera­
ble each time the ignition is switched on.
Lane assist display in the instrument
cluster
Applies to : vehicles wit h Audi act ive la ne ass ist
Fig. 100 Instrument cluster: monoc hrome disp lay
Fig. 101 Instrument cl uster : mult icolor displ ay
The lane assist disp lay can be called up using the
buttons in the
multifunction steering wheel
c:>poge 24.
Monochrome display
Refer to c:> fig. 100
101

Assist
CD Solid lines: active lane assist is sw itched
on and ready to provide warnings on the
side that is ind icated.
CD Blinking lines (left or right): using vibra-
tions in the steer ing wheel, active lane as -
sist is warning you that you are leaving
the lane .
@ Unfilled line(s): active lane assist is
sw itched on but is not ready to prov ide
warn ings.
No lines: active lane assist is sw itched off.
Multi-Color Display
Refer to c;, fig. 101
CD Solid white lines: active lane assist is
switched on and ready to provide warn- ings on the side that is indicated.
CD Red lines (left or right): using vib rations in
the steering wheel, active lane assist is
warning you that you are leaving the lane.
@ Solid gray lines: active lane assist is
sw itched on but is not ready to prov ide
war nings.
No lines: active lane assist is sw itched off.
Messages in the instrument cluster display
If the active lane assist has a malfunction, the
Pl1 indicator light in the instrument cluster dis ­
p lay turns off and one of the following messages
appears:
Audi active lane assist : currently not available.
No camera view
This message appears if the camera is unable to
detect the lines. This could happen if :
- The came ra field of view ¢
page 101, fig. 99 is
dirty or covered in ice. C lea n this area on the
winds hield.
- T he camera field of view is fogged over. Wait
until the fog has cleared before switching the
active lane assist on again.
- T he system has been unable to detect the lanes
for an extended period of time due to road con-
l) Thi s fun ctio n is not avai lab le in all count ries.
102
ditions. Switch the active lane assist back on
when the lines are more visible.
Audi active lane assist: currently unavailable
There is a temporary active lane assist malfunc­
tion. Try switc hing the active lane ass ist on again
l ate r.
Audi active lane assist: system fault!
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the malfunction corrected .
Pl1 Audi active lane assist: Please take over
steering
This message appears if you are not steering by
you rself. If this is the case, active lane assist does
not switch off, but it is "not ready" to provide a
warning. The system can help you keep the vehi­
cle in the lane. However, you are responsible for
driv ing the veh icle and must steer it yourself.
Adjusting the steering time and vibration
warning
Applies to: vehicles with Audi active lane assist
You can adjust individual active lane assist set­
tings in the MMI.
.,. Select: the I MENU I button> Car> Systems*
control button > Driver assistance > Audi ac­
tive lane assist .
Steering time
1 )
Early: in this setting, the corrective steering hap­
pens continuously to help keep the veh icle in the
center of the lane.
Late : in this setting, the system provides correc­
tive steering just before a vehicle wheel touches a
detected lane marker line.
Vibration warning
You can switch the additional vibrating warning
in the s teering whee l on or off . ..,.

<( co ..... N
" N ..... 0 r--. > 00
_& WARNING
With the vibration warning switched off, no
visible warning will appear in the instrument
cluster display when crossing a lane marker.
(D Tips
Market-spec ific: your settings are stored au­
tomatically and assigned to the remote con­
trol key in use .
Audi side assist
Description
Applies to: veh icles with Audi side assist
Fig. 102 Sensor detection range
Fig. 103 Disp lay on the exte rior mirro r
fR 0
0
> CX) Side assist he lps you monitor your blind spot and
traffic behind your vehicle. Wi thin the limits of
the system, it warns you about vehicles that are
coming closer or that are traveling with you with­ in sensor range@
¢fig. 102: if a lane change is
classified as critical, the display @ in the exter ior
mirror
¢ fig. 103 turns on .
The display in the left exterior mirror provides as­
sistance when making a lane change to the left,
while the display in the right exterior mirror pro-
Assist
vides assistance when making a lane change to
t h e right.
Information stage
As long as you do not act ivate the turn signal,
s ide ass ist
informs you about vehicles that are
detected and classified as critical. The display in
the mirror turns on, but is dim.
T he display remains dim in the information stage
so that your view toward the front is not distur­
bed.
Warning stage
If you activate the turn signal, side assist warns
you about vehicles that are detected and classi­
fied as critical. The display in the respective mir­
ror blinks brightly. If this happens, check traffic
by glancing in the rearv iew mirror and over your
shoulder¢ .&.
in General information on
page 104.
@ Tips
You can adjust the brightness on of t he dis­
play on the rearview mirror¢
page 105.
103