AUDI A4 1995 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-245

Engine Control Module (ECM), coding


Notes:

During Engine Control Module (ECM)
identification, a 5-digit code must always be
displayed.
Coding is carried out with the VAG 1551 scan
tool.
If coding that corresponds to the vehicle is not
displayed or if the ECM has to be replaced, the
ECM must be coded as follows:

- Connect VAG 1551 scan tool page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -7- to select "Code Control Module" function 07.
Rapid data transfer
Q
07 - Code Control Module

Indicated on display
- Press -Q- button to confirm input.
Code control module QEnter code number XXXXX
(0-32000
)

Indicated on display
- Enter code number for vehicle and press -Q- button to confirm input.
Coding variations page 01
-247
.
Pa
ge 341 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

______________________________________________
Function is unknown or cannot be carried out at the moment

If the following is indicated on the display:
A non-released code number has been entered.
______________________________________________
Pa
ge 342 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-246

8D0906266 2.8l V6/2V MPI OBD2
D01
Coding 01051
WSC 06388

ECM identification and entered coding (e.g. 01051) are shown.
-
Press button.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select "End Output" function 06.
Rapid data transfer
Q
06 - End Output

Indicated on display
- Press -Q- button to confirm input.
Rapid data transfer
HELP
Insert address word XX

Indicated on display
Notes:
The ECM uses the coding that is entered and displayed only after the
ignition has been switched off once. Incorrect coding leads to:
Driving performance problems (jerky shifting, rough load change, etc.)Increased fuel consumptionElevated exhaust gas valuesDecrease in transmission service lifeStoring of malfunctions that are not present in DTC memoryFunctions are not carried out (oxygen sensor control, triggering of the
EVAP canister system, etc.).
Pa
ge 343 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-247
Engine Control Module (ECM), coding variations
Country/exhaust gas
Drive/auxiliary function
Transmission
Vehicle type
00 = ----------------- 0 = Front wheel drive without
traction control 0 = 5-speed manual
transmission 0 = --------------
----
01 = Vehicle with Exhaust Gas
Recirculation (EGR) 1 = Front wheel drive with traction
control 1 = ------------------ 1 = A4
02 = ----------------- 2 = All wheel drive without traction
control 2 = ------------------ 2 = --------------
----
03 = ----------------- 3 = ------------------ 3 = ------------------ 3 = --------------
----
04 = ----------------- 4 = ------------------ 4 = ------------------ 4 = --------------
----
05 = ----------------- 5 = ------------------ 5 = Automatic trans. 01V 5 = --------------
----
06 = ----------------- 6 = ------------------ 6 = ------------------ 6 = --------------
----
Pa
ge 344 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-248
Note:
The code number will be composed as shown in the following example:
- Audi A4 1
- Automatic 01V 5
- Front wheel drive without traction control: 0
- Vehicle with EGR: 0 1
- Code number: 0 1 0 5 1
Note:
Vehicles with traction control (ATC) can be recognized by the ATC indicator light in the instrument cluster and/or by ABS
control module identification using the ABS On Board Diagnostic (OBD) program.
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01.

Pa
ge 345 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-249

Read Measuring Value Block (scan tool
function 08)


Notes:

Display groups 000-045 and 099 are identical to
the display groups 000-045 and 099 described
with "Basic Setting" function 04.
After "Basic Setting" function 04 is called up,
the ECM initiates the operations described
below. These operations are not carried out
after calling up "Read Measuring Value Block"
function 08.
Operations after calling up "Basic Setting"
function 04:
Constant ignition timing point of 12 BTDC will
be output in idle

Digital idle speed control is blocked
Evaporative Emissions (EVAP) canister purge
regulator valve is closed
A/C compressor is shut off

Pa
ge 346 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

EGR valve is closed
No coolant temperature correction; fixed value
80 C (176 F)

Learning values are relearned (idle and CO
content are adjusted automatically)
Pa
ge 347 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-250

- Connect VAG 1551 scan tool and operate until
display shows "Select function XX" page 01
-
7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
Note:
After the HELP button is pressed, an overview of possible functions is
printed out.
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08.
Rapid data transfer
HELP
08 - Read Measuring Value Block

Indicated on display
- Press -Q- button to confirm input.
Read measurin
g value block
HELP
Input displa
y group number XXX

Indicated on display
Note:
After the HELP button is pressed, the procedure for input of the display
group number is printed out.
Note:
Display group number 001 is used as an example to show the input - Input desired display group number according to display group
overview "Basic Setting" function 04, page 01
-150
.
Pa
ge 348 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

sequence.
Pa
ge 349 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-251

- Push buttons -0-, -0- and -1- for display group
number 001. Read measurin
g value block
Q
Input displa
y group number 001

Indicated on display
- Press -Q- button to confirm input.
Read measuring value block
1
1 2 3 4

Display fields 1 through 4 are indicated on the display.
Notes:
To change to another display group, proceed as follows:
Display group
VAG 1551 scan tool
VAG 1552 scan tool
Higher Press -3- button
Press button Lower Press -1- button
Press button Skipped Press -C- button Press -C- button
The values in display fields 1 through 10 are shown in decimal form in
display group 000. The current 3-digit display group number is shown without the first
zero. In display groups 000 to 009, the number is shown without the
first two zeroes. When the printer is switched on, the current display is printed on the
paper strip. Every time the PRINT button is pressed, the current display is printed
out again.
Pa
ge 350 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1