sensor AUDI A4 1995 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Repair Manual

01-69


Metal chips on engine speed (RPM) sensor -G28- or
distance from the engine speed (RPM) sensor -G28- to the
flywheel ring greater than 1.2 mm (0.049 in.)

- Remove engine speed (RPM) sensor -G28-,
check for contamination, clean if necessary

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check DTC
memory again

Wiring connection to engine speed (RPM) sensor -G28-
faulty or sensor -G28- faulty

- Check and adjust engine speed (RPM) sensor -
G28- page 28
-21


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check DTC
memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and test drive
check DTC memory
Note:
If the malfunction "P0322 / 16706" is recognized during engine start, no ignition or fuel injection occurs.
Pa
ge 93 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-70

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0327 / 16711
Knock Sensor 1 Circuit Low
Input (Bank 1 or Single
Sensor) Malfunction P0332 / 16716
"Knock Sensor 2 Circuit Low Input"
Also in DTC memory
No
Yes

- Check knock sensor 1 -G61- and knock
sensor 2 -G66- page 28
-29


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check
DTC memory again
MIL Status:
MIL lights up immediately
Harness connector for Knock Sensor
(KS) 1 -G61- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1
For troubleshooting
Display group 015
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check
DTC memory again

Knock Sensor (KS) 1 -G61- loose

- Check mounting of knock sensor 1 -G61-
and if necessary retighten use insert
3247; tightening torque 20 Nm (15 ft lb)

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check
DTC memory again
Pa
ge 94 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-71


Wiring connection to Knock Sensor (KS) 1 -
G61- faulty, or sensor -G61- faulty

- Check knock sensor 1 -G61- page 28
-29

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and check DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265

erase DTC memory and test drive check DTC memory
Note:
The malfunction "P0327 / 16711" is set if the output voltage of the knock sensor is too low (below 0.2 V) (coolant temperature
over 20 C (68 F)/ engine speed greater than 3500 RPM and engine load greater than 16%). The ignition angle is then
retarded by 12 crankshaft in the knocking areas of the map (engine load greater than 40%).
Pa
ge 96 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-72

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P0332 / 16716
Knock Sensor 2 Circuit
Low Input (Bank 2) Malfunction P0327 / 16711 "Knock
Sensor 1 Circuit Low Input (Bank 1 or
Single Sensor)" also in DTC memory
No
Yes

- Check knock sensor 1 -G61- and knock
sensor 2 -G66- page 28
-29


Malfunction cause found: Yes
No

- Erase DTC memory, test drive, and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Harness connector for Knock Sensor
(KS) 2 -G66- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-
1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
For troubleshooting
Display group 016
Knock Sensor (KS) 2 -G66- loose

- Check mounting of knock sensor 2 -G66-
and if necessary retighten use insert 3247;
tightening torque 20 Nm (15 ft lb)

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
Pa
ge 97 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-73


Wiring connection to Knock Sensor (KS) 2 -
G66- faulty or sensor -G66- faulty

- Check knock sensor 2 -G66- page 28
-29

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test drive, check DTC
memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265

erase DTC memory and test drive check DTC memory
Note:
The malfunction "P0332 / 16716" is set when the knock sensor output voltage is too low (under 0.2 V) (coolant temperature
over 20 C (68 F) / engine speed greater than 3500 RPM and engine load greater than 16%). The ignition angle is then
retarded by 12 crankshaft in the knocking ranges of the map (engine load greater than 40%).
Pa
ge 99 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-74

Output on GST
and/or on VAG 1551
scan tool Possible malfunction cause

Malfunction repair
P0337 / 16721
Crankshaft Position
Sensor Circuit Low
Input Harness connector for Crankshaft Position
(CKP) sensor -G4- loose or corroded due to
moisture in the harness connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 28
-7

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Crankshaft Position (CKP) sensor -G4-
loose or distance to groove on crankshaft
counterweight greater than 1.3 mm (0.053
in.)

- Check crankshaft position sensor -G4- for
correct installation and tight fit

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again

Wiring connection to Crankshaft Position
(CKP) sensor -G4- faulty, or sensor -G4-
faulty

- Check crankshaft position sensor -G4-
page 28
-19


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
Pa
ge 100 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-75


Engine Control Module
(ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC
memory and test drive check DTC memory
Note:
The malfunction "P0337 / 16721" is set at an engine speed between 25 RPM and 400 RPM as soon as no crankshaft sensor
signal is recognized for longer than 3 sec.
Pa
ge 102 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-79

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0422 / 16806
Main Catalyst Efficiency
Below Threshold (Bank 1) Are other malfunctions stored in the DTC
memory?

No

Yes

- First correct these malfunctions
according to Diagnostic Trouble Code
(DTC) table.
MIL Status:
MIL lights up after 2 Trips Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Bank 1 Three Way Catalytic Converter
(TWC) chemically or thermally aged or
mechanically destroyed

- Replace Three Way Catalytic
Converter (TWC) Bank 1
For troubleshooting
Display groups 035, 036,
044
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Note:

With the help of the Oxygen Sensor Probe in front of and behind the Three Way Catalytic Converter (TWC), the rate of
Three Way Catalytic Converter (TWC) deterioration is determined using the Three Way Catalytic Converter (TWC) oxygen
storage capability.
Pa
ge 107 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-80

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0432 / 16816
Main Catalyst Efficiency
Below Threshold (Bank 2) Are other malfunctions stored in the DTC
memory?

No

Yes

- First repair these malfunctions
according to Diagnostic Trouble Code
(DTC) table.
MIL Status:
MIL lights up after 2 Trips Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Bank 2 Three Way Catalytic Converter
(TWC) chemically or thermally aged or
mechanically destroyed

- Replace Bank 2 Three Way
Catalytic Converter (TWC)
For troubleshooting
Display groups 035, 036,
044
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Note:

With the help of the Oxygen Sensor Probe in front of and behind the Three Way Catalytic Converter (TWC), the rate of
Three Way Catalytic Converter (TWC) deterioration is determined using the Three Way Catalytic Converter (TWC) oxygen
storage capability.
Pa
ge 108 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-81

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0440 / 16824
Evaporative Emission
Control System Malfunction Evaporative emissions system hoses
kinked or pinched

- Check hoses for correct fit

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
MIL lights up after 2 Trips Leak in the EVAP system between
Intake manifold and EVAP canister
purge regulator valve -N80- or
EVAP canister purge regulator valve -
N80- and sensor for EVAP canister -
G172- or
Sensor for EVAP canister -G172- and
EVAP canister
- Check EVAP system for leaks

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 109 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1