warning AUDI A4 1995 B5 / 1.G Brakes ESP DTC Table Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1995, Model line: A4, Model: AUDI A4 1995 B5 / 1.GPages: 96, PDF Size: 0.3 MB
Page 2 of 96
01-357
DTC table; DTCs from 00000 to 00526
Printed output from VAG1551
Scan Tool (ST) Possible cause
Corrective action
DTC
00000
No malfunction recognized!
If this display appears, process is
concluded. No DTCs are stored in
DTC memory.
If there are still problems or
malfunctions anyway, check the
following points:
If one or more indicator lamps light up anyway,
one of the wires that activates the indicator
lamps may be malfunctioning. Missing signal from parking brake warning light
switch -F9-. (parking brake set or released). - See section "Overview of
indicator lamp functions"
page 01
-222
.
Check the parking brake
warning light switch -F9-.
- "Read measuring value block"
function 08 page 01
-256
,
display group 2.
See continuation on next page
Missing signal from brake light switch -F.
Check the brake light switch
-F.
- "Read measuring value block"
function 08 page 01
-256
,
display group 2.
Pa
ge 2 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 21 of 96
01-375
DTC table; DTCs from 00532 to 01421
Printed output from VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
00532
Voltage supply
See continuation on next page
This malfunction affects the voltage supply
of the control module.
This DTC is only stored, if it occurs the first
time the vehicle exceeds 6 km/h.
As soon as the supply voltage is again
within the valid voltage range, the system
is switched back on and the warning lights
turn off.
Open circuit or resistance too high
between voltage supply of terminal 15
and ABS control module -J104-
(terminal 1). Open circuit or resistance too high in
the Ground (GND) supply to ABS
control module -J104- (terminals 28
and 29). Voltage jumps in vehicle system. Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Repair Manual, Electrical
Equipment, Repair Group 27, Battery
- "Read measuring value block"
function 08 page 01
-256
,
display group 6.
- Carry out "Electrical test",
step 21 page 01
-323
- Check Generator (GEN) and
Voltage Regulator (VR). - Check battery
Pa
ge 21 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 22 of 96
01-376
Printed output from VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC
00532
Continuation:
Voltage supply
Signal too small
This malfunction affects the voltage supply
of the control module.
This DTC is only stored, if it occurs the first
time the vehicle exceeds 6 km/h.
As soon as the supply voltage is again
within the valid voltage range, the system
is switched back on and the warning lights
turn off.
Open circuit or resistance too high
between voltage supply of terminal 15
and ABS control module -J104-
(terminal 1). Open circuit or resistance too high in
the Ground (GND) supply to ABS
control module -J104- (terminals 28
and 29). Voltage jumps in vehicle system. Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Repair Manual, Electrical
Equipment, Repair Group 27, Battery
- "Read measuring value block"
function 08 page 01
-256
,
display group 6.
- Carry out "Electrical test",
step 21 page 01
-323
- Check Generator (GEN) and
Voltage Regulator (VR). - Check battery
Pa
ge 22 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 43 of 96
01-395
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Sensor for transverse acceleration -
G200- not installed correctly.
Repair Manual, Brake System, Repair Group 45
- Check the installation position of the sensor for
transverse acceleration -G200-.
See continuation on
next page
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and ABS
control module -J104- (terminal 19).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 75).
Pa
ge 43 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 44 of 96
01-396
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 44 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 45 of 96
01-397
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Sensor for transverse acceleration -
G200- not installed correctly.
Repair Manual, Brake System, Repair Group 45
- Check the installation position of the sensor for
transverse acceleration -G200-.
See continuation on
next page
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and ABS
control module -J104- (terminal 69).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 67).
Pa
ge 45 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 46 of 96
01-398
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 46 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 47 of 96
01-399
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
See continuation on
next page
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
Pa
ge 47 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 48 of 96
01-400
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 4B0 907 389
01423
Continuation:
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
There is an open circuit in one of the
supply wires for the sensor for
transverse acceleration -G200-.
Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check Ground (GND) between sensor for
transverse acceleration -G200 (terminal 1) and
ABS control module -J104- (terminal 19).
- Check voltage supply between sensor for
transverse acceleration -G200 (terminal 3) and -
J104- ABS control module (terminal 75).
See continuation on
next page Note: Only replace the control module as a
last resort.
ABS control module -J104-
malfunctioning
Repair Manual, Brake System, Repair Group 45
- If the malfunction cannot be fixed, replace the
ABS control module -J104-.
Pa
ge 48 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17
Page 49 of 96
01-401
Printed output from
VAG1551 Scan Tool
(ST) Possible cause
Corrective action
DTC WARNING!
This is only valid for control modules with no.: 8D0 907 389, 8D0 907 389A, 8D0 907 389D
and 8D0 907 389E.
01423
Sensor for transverse
acceleration -G200-
Failure in electrical
circuit
Continuation:
Open circuit in signal line to sensor for
transverse acceleration -G200-.
Short circuit to B+ or Ground (GND) in
signal line to sensor for transverse
acceleration -G200-. Electrical Wiring Diagrams, Troubleshooting &
Component Locations - Check signal line between sensor for transverse
acceleration -G200 (terminal 2) and ABS control
module -J104- (terminal 18).
See continuation on
next page
Sensor for transverse acceleration -
G200- malfunctioning.
Repair Manual, Brake System, Repair Group 45
- If none of the causes listed are causing the
malfunction, replace sensor for transverse
acceleration -G200-.
Pa
ge 49 of 96 Electronic Stabilization Pro
gram
(ESP
) DTC table
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.17