ignition AUDI A4 1995 B5 / 1.G Interior Monitor Workshop Manual

01-111

- Switch ignition on.

- Switch printer on by pressing PRINT button
(indicator lamp in button lights up).

- Press button -1- to select "Rapid data transfer"
operating mode 1. Rapid data transfer
HELP
Insert address word XX

Indicated on display
Address word for interior monitoring: 45
- Press buttons -4- and -5- to insert "Int. Monitoring" address word 45.
Rapid data transfer
Q
45 - Int. Monitoring

Indicated on display
- Press -Q- button to confirm input.
4B0951173 Int. Monitoring
D00
Coding 00101
WSC 06812

Indicated on display after about 5 seconds
Note:
A list of available functions is printed out when the HELP button is
pressed. -
Press button.
Pa
ge 6 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4

01-114

No DTC recognized

If the message "No DTC recognized" is displayed, the program can be
returned to the starting point by pressing the button.
Rapid data transfer
HELP
Select function XX

Indicated on display
If something else is displayed:
Scan tool operating instructions - Erase DTC Memory (function 05) page 01
-137
.
- End Output (function 06) page 01
-139
.
- Switch ignition off and Disconnect VAG1551 Scan Tool (ST) from Data
Link Connector (DLC).
Pa
ge 9 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4

01-122

Interior monitoring function test


- Open side window approx. 10 cm.

- Switch ignition off and remove ignition key.

- Close all doors.

- Lock vehicle, which will set the anti-theft warning
system and the interior monitoring.

- Wait 30 seconds until all warning lamps in door
trim blink slowly in 2 second intervals (f = 0,5
Hz).

- Insert hand through window opening and hold in
proximity of sensor.

- If the interior monitoring is OK, alarm will be
triggered. An entry into DTC memory of control
module for central locking "1370; alarm via
interior monitoring" as well as to ultra-sound
control module "alarm via sensor for ATS, fl, fr,
rl, rr".

- Switch off alarm by unlocking vehicle.

-
DTC must be checked and erased in DTC
Pa
ge 20 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4

01-128

Testing alarm signal

- Switch ignition off and remove ignition key.

- Connect VAG1551 Scan Tool (ST) ( page 01
-
1 ), and press buttons -4- and -5- to select "Int.
Monitoring" address word 45.

- Close all doors and open one side window.

- Lock vehicle by reaching through open window.
The anti-theft system horn confirms this, but
warning lamps do not light up.

- Wait 30 seconds until anti-theft system is
armed.

- Perform Output Diagnostic Test Mode ( page
01
-124
) and select control element test "Create
active alarm."

Notes:

It is also possible to test the alarm activation
signal without using the VAG1551 Scan Tool
(ST). To do this, carry out the first, third, fourth
and fifth procedure steps listed above.

Pa
ge 28 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4

01-138

Notes: Attention! DTC Memory was not interrogated

This message indicates an error in the test sequence.
Rapid data transfer DTC Memor
y was not interro
gated

Adhere exactly to the test sequence: first check DTC memory and, if
necessary, repair malfunctions, then erase DTC memory.
After erasing DTC memory carry out function 06 "End Output" then switch
ignition off and on again and check DTC memory again.
This message indicates an error in the test sequence.
Pa
ge 43 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4

01-139

End Output (scan tool function 06)


Carrying out "End Output" function 06
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -6- to select "End Output" function 06.
Rapid data transfer
Q
06 - End Output

Indicated on display
- Press -Q- button to confirm input.
Rapid data transfer
HELP
Insert address word XX

Indicated on display
- Switch ignition off.
- Disconnect VAG1551 Scan Tool (ST) from Data Link Connector (DLC).
Pa
ge 44 of 44 Ultrasonic interior monitorin
g On Board Dia
gnostic
(OBD
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD04.01.4