display AUDI A4 1996 B5 / 1.G 01V Transmission Read Measuring Value Block E 17 User Guide

01-197
1) While driving, a second mechanic is required to read specifications. 2) Also referred to as the sensor for transmission output RPM -G195-. 3) Indication should mimic the engine speed in display field 1, i.e. when engine speed increases or decreases, transmission
RPM (output RPM) should increase or decrease.
Notes for display group number 001, display field 1 to 3;
Test conditions: Shifting process must be finished. Vehicle must not be in deceleration mode (no down-hill driving or
engine braking).
Pa
ge 14 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-198
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test requirements
Spec. value on
V.A.G 1551
display Corrective actions
001
4 Gear
selected while
driving
1) Selector lever
position
- Check solenoid valves. See
display group number 005 and
006

"N"
"1"..."5"
2)
- See DTC table, DTC numbers of
appropriate solenoid valves

"R" "R"
- Check selector lever position.
Display group number 004

"D" "1" "2" "3" "4"
"5"

"4" "1" "2" "3" "4"

"3" "1" "2" "3"

"2" "1M" "2"
Notes and footnotes for display field 4 of display group number 001 are on the next page.
Pa
ge 15 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-200
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec.
value on
V.A.G
1551
display Corrective actions
002 1 Dynamic code
number (of dynamic
shifting program) Under normal
driving
conditions
1) Min. value (very
economical) 0
Determined by driving style and
street conditions (acceleration,
accelerator pedal movement,
speed and load)

Max. value
(very sporty)
240 High values move shift points
to higher engine speeds

Warm-up program is active
241

Anti-Slip Regulation (ASR)
active 242
Shifting avoided whenever
possible

Tiptronic recognition activated
243 - See appropriate DTCs for
Tiptronic Switch -F189-

Cruise control system
characteristic map 244
Only for USA, not applicable
yet
Pa
ge 17 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-201
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
002
2 Throttle valve value While
standing idle 0...1 % When accelerating from idle to
Wide Open Throttle (WOT), %-
value increases steadily.


Wide Open
Throttle
(WOT)
99...100 % - Perform electrical test
page 01
-273

- See respective DTCs of
Throttle Position (TP) sensor -
G69-

3 Transmission Vehicle
Speed (VSS) sensor -
G38-
2) While driving
1)
0...8200
- See appropriate DTC for VSS
-G38- (-G195-)
2)
- See display group number
001

4 Gear selected See display group number 1, display field 4
1) While driving, a second mechanic is required to read specifications. 2) Also referred to as sensor for transmission output RPM -G195-.
Pa
ge 19 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-202
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
003
1 Brake light switch
-F- Brake
not
operated
- - See appropriate DTCs for brake
light switch -F-

Brake
activated Brake
- Perform electrical test page
01
-273


2 Shift lock
solenoid -N110-
2) While
standing brake not
operated P N active
- See appropriate DTC for shift
lock solenoid -N110-
2)

brake
activated
P N not
selected - Check shift lock solenoid -N110-.
Perform electrical test page 01
-
273




Continue 3 Speed
While driving
1)
...km/h Speedometer display and value on
V.A.G1551 may deviate slightly
from each other.
- If necessary, check Speedometer
Vehicle Speed sensor (VSS) -G22-
Pa
ge 20 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-203
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
003
4 Supply voltage,
terminal 15 While
standing
min.
10.0 V - Perform electrical test page 01
-
273



max. 16.0 V
- See DTC table, DTC 00532
page 01
-45

004



Continue

1 ATF temperature
While standing with
engine running. ... C
- Perform electrical test page 01
-
273

- See appropriate DTCs for
Transmission Fluid (ATF)
Temperature sensor -G93-
Notes for ATF temperature:

Recognized temperature of minus 50 C indicates a short circuit to Ground (GND)
Pa
ge 22 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-204
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test
requirements Spec. value
on V.A.G
1551
display Corrective actions
004 2 Selector lever position -
(Multi-function
Transmission Range
(TR) switch -F125-) While
standing P P
- Check TR switch -F125-. Display
group no. 004
Selector
R R
- Perform electrical test page 01
-
273

lever
N N Check for agreement with indication in
instrument cluster
in
D D

4 4

3 3
- If necessary adjust selector lever
bowden cable

Continue


2 2 Repair Manual, 5 Spd. Automatic
Transmission 01V, Repair Group 37, shift mechanism, repairing
Pa
ge 24 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-205
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
004
3 Multi-function
Transmission Range
(TR) switch -F125- while
standing Selector
lever
position
L1 L2 L3 L4 - See appropriate DTC for TR
switch -F125-
1)

P 1000
- Check TR switch -F125-

R 0100
- Perform electrical test page
01
-273


N 1110

D 1011
- If necessary adjust selector
lever bowden cable

4 0111 Repair Manual, 5 Spd.
Automatic Transmission 01V, Repair Group 37, shift mechanism, repairing

Continue
3 0001


2 0010
Pa
ge 25 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-206
Notes for display field 3 of display group number 004:

Input signals of Multi-function Transmission Range (TR) switch -F125- can be checked at the Transmission Control
Module (TCM).

Display field 3: (from left to right)
L 1 L 2 L 3 L 4
Wiring connection to TCM -
J217- Terminal 36 of -
J217- Terminal 8 of -J217-
Terminal 37 of -
J217- Terminal 9 of -J217-

Pa
ge 26 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-207
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test
requirements Spec. value on
V.A.G 1551
display Corrective actions
004

without
CAN-bus 4 Engine
intervention
(ignition
intervention) While driving
1)
Engine speed
signal OK
- See DTC table, DTC 00545, 18192
and 18193 page 01
-45


is
switched on

Engine interv. - Perform electrical test page 01
-273
- Check wire connection to Engine
Control Module (ECM)

is
switched off -
- Only replace Transmission Control
Module (TCM) -J217- if necessary
page 01
-11

1) While driving, a second mechanic is required to read specifications.
Notes for display field 4 of display group number 004 are on the next page:
Pa
ge 27 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13