engine AUDI A4 1996 B5 / 1.G 01V Transmission Read Measuring Value Block E 17 User Guide

01-200
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec.
value on
V.A.G
1551
display Corrective actions
002 1 Dynamic code
number (of dynamic
shifting program) Under normal
driving
conditions
1) Min. value (very
economical) 0
Determined by driving style and
street conditions (acceleration,
accelerator pedal movement,
speed and load)

Max. value
(very sporty)
240 High values move shift points
to higher engine speeds

Warm-up program is active
241

Anti-Slip Regulation (ASR)
active 242
Shifting avoided whenever
possible

Tiptronic recognition activated
243 - See appropriate DTCs for
Tiptronic Switch -F189-

Cruise control system
characteristic map 244
Only for USA, not applicable
yet
Pa
ge 17 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-203
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
003
4 Supply voltage,
terminal 15 While
standing
min.
10.0 V - Perform electrical test page 01
-
273



max. 16.0 V
- See DTC table, DTC 00532
page 01
-45

004



Continue

1 ATF temperature
While standing with
engine running. ... C
- Perform electrical test page 01
-
273

- See appropriate DTCs for
Transmission Fluid (ATF)
Temperature sensor -G93-
Notes for ATF temperature:

Recognized temperature of minus 50 C indicates a short circuit to Ground (GND)
Pa
ge 22 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-207
Only for transmission with hydraulic control -E17-
Display
group
number Display
field Description
Test
requirements Spec. value on
V.A.G 1551
display Corrective actions
004

without
CAN-bus 4 Engine
intervention
(ignition
intervention) While driving
1)
Engine speed
signal OK
- See DTC table, DTC 00545, 18192
and 18193 page 01
-45


is
switched on

Engine interv. - Perform electrical test page 01
-273
- Check wire connection to Engine
Control Module (ECM)

is
switched off -
- Only replace Transmission Control
Module (TCM) -J217- if necessary
page 01
-11

1) While driving, a second mechanic is required to read specifications.
Notes for display field 4 of display group number 004 are on the next page:
Pa
ge 27 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-208
Notes for display field 4 of display group number 004:

This display field 4 is only valid for vehicles without CAN-bus, refer to next page for vehicles with CAN-bus. A)
Engine intervention is only activated during the shifting process. Depending on the driving situation, engine intervention
may only be activated briefly, i.e. the relatively slow data transfer to the V.A.G1551 can miss this brief engine intervention
under certain driving conditions.
A) There is a distinction made between vehicles with and without CAN-bus. For information on which vehicles are equipped
with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

Pa
ge 28 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-209
Only for transmission with hydraulic control -E17-
Display group
number Display
field Description
Test
requirements Spec. value
on
V.A.G 1551
display Corrective
actions
004

with
CAN-bus 4 Information of On Board
Diagnostic (OBD)
Indicated on display from left to
right While driving
1)

Malfunction display switched on
1

switched off 0

Trip completed 1

not completed 0 not applicable

Transmission warm-up
completed 1

not completed 0

Engine start
recognized 1

not recognized 0
1) While driving, a second mechanic is required to read specifications.
Notes for display field 4 of display group number 004 see next page
Pa
ge 29 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-210
Notes for display field 4 of display group number 004:

This display field 4 is only valid for vehicles with CAN-bus, refer to previous display field 4 for vehicles without CAN-bus.
A)
A) There is a distinction made between vehicles with and without CAN-bus. For information on which vehicles are equipped
with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, aggregate allocation, ratios,
equipment

Pa
ge 30 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-215
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec.
value on
V.A.G
1551
display Corrective actions
007 1 ATF temperature
While standing with engine
running. When temperature
sensor is faulty, a replacement
value is transmitted. ... C
- Check Transmission Fluid
(ATF) Temperature sensor -
G93-; perform electrical test
page 01
-273


2 Specified current
of solenoid valve 7
-N94-
2) While driving
1)
min. 0.1 A
- See DTC table, DTC 270
page 01
-45



max 0.8 A
- Perform electrical test
page 01
-273


3 Torque converter
lock-up clutch While driving
1)
TC open
- See DTC table, DTC 1192
page 01
-45



TC control
- Perform electrical test
page 01
-273

Continue


TC closed
Pa
ge 35 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-216
Only for transmission with hydraulic control -E17-
Display
group
No. Display
field Description
Test requirements
Spec. value on
V.A.G 1551
display Corrective actions
007
4 Torque
converter slip
speed hile
driving
1) TC open 0......standstill
RPM
- See DTC table, DTC 00297,
00660 and 01192 page 01
-45



TC control (last
shift operation at
least 20 sec ago) 20...120 RPM
Repair Manual, 5 Spd.
Automatic Transmission 01V, Repair Group 37, transmission with shift elements
- Determine which element is
faulty or not activated,
transmission with shift elements

TC closed 0...10 RPM
- Check plausibility between
engine, transmission input- and
transmission speed; Display
group number 001
1) While driving, a second mechanic is required to read specifications.
Notes for display field 4 of display group number 004 are on the next page:
Pa
ge 37 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-219
Only for transmission with hydraulic control -E17-
Display
group No. Display
field Description
Test requirements
Spec. value
on V.A.G
1551
display Corrective actions
008
3
3)

without
CAN-
bus Throttle valve
duty cycle While
standing idle smaller than
30% When accelerating from idle to Wide Open
Throttle (WOT), %-value increases
steadily.


Wide Open
Throttle
(WOT)
more than
70% - Perform electrical test page 01
-273
- See DTC table, DTC 00518 and 00638
page 01
-45


Continue

3
2)

with
CAN-
bus Engine torque
While driving
1)
Nm
The signal for actual engine torque is
transmitted by the Engine Control Module
(ECM) to the Transmission Control Module
(TCM) via the CAN-bus wiring.
Notes and footnotes for display group number 008 are on the next page.
Pa
ge 40 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13

01-220
Only for transmission with hydraulic control E17
Display
group
number Display
field Description
Test requirements
Spec. value on
V.A.G 1551
display Corrective actions
008
4 Signal for
deceleration/engine under
load While
driving
1) Deceleration
mode Deceleration For declines or delay
(engine brake)


Engine under
load
- Engine is under load in
normal driving
conditions.
1) While driving, a second mechanic is required to read specifications. 2) Only for vehicles with CAN-bus For information on which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

3) Only for vehicles without CAN-bus For information on which vehicles are equipped with CAN-bus
Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00, engine codes, unit allocation, ratios, equipment

Pa
ge 41 of 49 Read Measurin
g Value Block
(scan tool function 08
) for transmissions with h
ydraulic control -E17-
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.13