wheel bolts AUDI A4 1996 B5 / 1.G AEB ATW Engines Exhaust System Components Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A4, Model: AUDI A4 1996 B5 / 1.GPages: 35, PDF Size: 0.46 MB
Page 3 of 35

26-2
Front-wheel-drive vehicles
1 -
Nut
40 Nm (30 ft b)
2 -
Double clamp Before tightening, ensure exhaust system
is free of stress Page 26
-24
Installation position: bolt ends point toward
left Installation position of bolt ends Page 26
-13
, Fig. 3
Tighten bolts evenly
3 -
Nut 40 Nm (30 ft b)
4 -
Double clamp Used when front or rear muffler is replaced
separately Before tightening, ensure exhaust system
is free of stress Page 26
-24
Installation position: bolt ends point toward
rear Installation position of bolt ends %page
Page 26
-13
, Fig. 3
Tighten bolts evenly
Pa
ge 3 of 35 Exhaust s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.26.1
Page 21 of 35

26-16
All-wheel-drive vehicles
- Using VAG1523 saw, cut exhaust pipe at separating point (arrow) at
right angle.
- When installing, center double clamp over separating point.
Double clamp installation position: level with bolts in clamp -1- pointing
toward left-rear wheel
- Install double clamp so that bolts don't project over lower edge of
double clamp Page 26
-13
, Fig. 3
.
- Align exhaust system free of stress Page 26
-24
.
- Tighten double clamp bolts evenly to 40 Nm (30 ft lb).
Pa
ge 21 of 35 Exhaust s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.26.1
Page 31 of 35

26-24
Exhaust system, aligning free of stress
Align exhaust system when cold
Front-wheel-drive vehicles
- Remove double clamp bolts Page 26
-2 , item
2 .
Aligning tailpipes: - Push exhaust system forward (arrow) until tension on rear mount
equals dimension -a-.
Dimension -a- = 7-9 mm (0.275-0.354 in.)
- Tighten double clamp bolts evenly to 40 Nm (30 ft lb).
- Align tailpipes so distance -a- on left and right side is equal.
- Distance -b- between bumper cutout and tailpipes must equal
specification.
Distance -b- = 40-46 mm (1.57-1.81 in.)
Pa
ge 31 of 35 Exhaust s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.26.1
Page 32 of 35

26-25
All-wheel-drive vehicleswithout double clamp
between front and rear mufflers
- Remove double clamp bolts Page 26
-9 , item
- 12 -.
Aligning tailpipes: - Push exhaust system forward (arrow) until initial preload on right rear
mount equals dimension -a-.
Dimension -a- = 7-11 mm (0.275-0.433 in.)
- Tighten double clamp bolts evenly to 40 Nm (30 ft lb).
- Align tailpipes so distance -a- on left and right-sides is equal.
- Distance -b- between bumper cutout and tailpipes must equal
specification.
Distance -b- = 41-47 mm (1.614-1.850 in.)
Pa
ge 32 of 35 Exhaust s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.26.1
Page 33 of 35

26-26
All-wheel-drive vehicleswith double clamp
between front and rear mufflers
Note:
Only for vehicles with double clamp between
front and rear mufflers: also align front muffler.
- Remove double clamp bolts Page 26
-9 , item
- 12 - and Page 26
-10
, item - 22 -.
- Push exhaust system forward (arrow) until initial preload on left rear
mount equals dimension -a-.
Dimension -a- = 7-9 mm (0.275-0.354 in.)
- Tighten front double clamp bolts evenly to 40 Nm (30 ft lb) Page 26
-
9 , item - 12 -.
Pa
ge 33 of 35 Exhaust s
ystem com
ponents, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.26.1