engine oil AUDI A4 1996 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Workshop Manual

01-23

Diagnostic Trouble Code (DTC)
Malfunction text
MIL switching condition
SAE
VAG
P1325 17733 Cyl.1-Knock Control Limit Attained off
P1326 17734 Cyl.2-Knock Control Limit Attained off
P1327 17735 Cyl.3-Knock Control Limit Attained off
P1328 17736 Cyl.4-Knock Control Limit Attained off
P1329 17737 Cyl.5-Knock Control Limit Attained off
P1330 17738 Cyl.6-Knock Control Limit Attained off
P1339 17747 Crankshaft Pos./Engine Speed Sensors Cross connected immediately
P1341 17749 Ignition Coil Power Output Stage 1 Short to Ground immediately
P1343 17751 Ignition Coil Power Output Stage 2 Short to Ground immediately
P1345 17753 Ignition Coil Power Output Stage 3 Short to Ground immediately
P1391 17799 Camshaft Pos.Sensor (B2) Short to Ground immediately
P1392 17800 Camshaft Pos.Sensor Open Circ. (B2) Short to B+ immediately
P1393 17801 Ignition Coil Power Output Stage 1 Electrical Malfunction immediately
P1394 17802 Ignition Coil Power Output Stage 2 Electrical Malfunction immediately
P1395 17803 Ignition Coil Power Output Stage 3 Electrical Malfunction immediately
Pa
ge 34 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-52

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0170 / 16554
Fuel Trim Malfunction (Bank 1) Air leak in the area of the intake
manifold

- Find and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
check DTC memory again

Oil dilution (fuel in the oil) because
of frequent cold starts or driving short
distances

- Check, if necessary do oil change
MIL Status:
MIL lights up after 2 Trips Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
check DTC memory again

Mass Air Flow (MAF) sensor -G70-
supplies false signal

- Check Mass Air Flow (MAF) sensor -
G70- page 24
-81

For troubleshooting Display
groups 005, 007, 009 and 010
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
check DTC memory again

Oil burning with faulty piston

Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 15
- Check compression pressure

Malfunction cause found: Yes

Pa
ge 70 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-56

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0173 / 16557
Fuel Trim Malfunction (Bank 2) Air leak in the area of the manifold

- Find and repair leak

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
check DTC memory again

Oil diluted (fuel in the oil) because
of frequent cold starts for driving short
distances

- Check and change oil if necessary
MIL Status:
MIL lights up after 2 Trips Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
check DTC memory again

Mass Air Flow (MAF) sensor -G70-
supplies false signal

- Check Mass Air Flow (MAF) sensor -
G70- page 24
-81

For troubleshooting Display
groups 006, 008, 009 and 010
Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and
check DTC memory again

Oil burning with faulty piston

Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair - Check compression pressure
Pa
ge 77 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-115


Camshaft Position (CMP) sensor -G40- oily or dirty
on the inside because of leaking seal on the cylinder
head.

- Camshaft Position (CMP) sensor -G40- and check for
contamination. If it is oily, replace seal on cylinder head

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test drive, check
DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC memory and test drive check DTC
memory
Notes:

The malfunction "P1340 / 17748" is set as soon as the crankshaft position sensor signal is always "high" at an engine
speed between 50 RPM and 4000 RPM and with more than 20 crankshaft sensor signals recognized.
Pa
ge 156 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
drive, check DTC memory again

Wiring connection to ignition coil power
output stage -N122- faulty or power output
stage -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test
drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and test
drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 158 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-120


Camshaft Position (CMP) sensor -G40- oily or
dirty on the inside because of leaky seal on cylinder
head

- Remove Camshaft Position (CMP) sensor -G40- and
check for contamination. If it is oily, replace seal on cylinder
head

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after test drive, check
DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265

check DTC memory and test drive check DTC
memory
Notes:

The malfunction "P1392 / 17800"is set as soon as the crankshaft position sensor signal is always "high" at an engine
speed between 50 RPM and 4000 RPM and with more than 20 crankshaft sensor signals recognized.
Pa
ge 162 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

No
test drive, check DTC memory again

Wiring connection to Power output stage -
N122- for ignition coils or -N122- faulty

- Check Power output stage -N122- for
ignition coils page 28
-13


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
check DTC memory and
test drive check DTC memory
Note:
The power output stage is not integrated in the Engine Control Module (ECM) -J192-, it is a separate component.
Pa
ge 164 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-183
Notes on display field 1 (cont'd):
The oxygen sensor control stop evaluation is also done by the diagnosis only after successful learning learning
requirement display:
Control stop max.: + 32%
Control stop min.: - 87.5%
With values of more than 20% in "Basic Setting" function 04, the following malfunctions are possible: Intake air leaks
Engine damage (oil burning with faulty piston)
Notes on display field 2:
In display field 2 (learning range display), the momentary learning range (load status) is displayed. Only idle and partial
throttle learning ranges are displayed since, at wide open throttle, no learning takes place.
In order to reach the corresponding learning range (load status):
Idle: the vehicle should be allowed to run at idle (650-900 RPM)
Partial throttle 1, 2 or 3: during test drive (with second person), increase engine speed to 1500-3000 RPM and generate
load by lightly operating the brake
X
X
X
X
Meaning of 4-digit learning range display
Pa
ge 256 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

If there is engine damage (oil burning because of faulty piston)
If a knock sensor malfunction is recognized in DTC memory, ignition map switching is blocked.
Notes on display field 4:
Knock control is active starting at an engine load greater than 40% Display groups 013 and/or 014. The ignition timing point retarding values are only used when knock control is "active."
Pa
ge 274 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-196
Display groups 013 and 014
Notes on display fields 2, 3 and 4:
Knock control is active starting at an engine load greater than 40%. If the engine load exceeds 40%, the current ignition timing
point retarding value is displayed; if the engine load drops below 40%, the last values used are displayed constantly.
If there is audible knocking without recognizable retarding of the ignition timing point, the engine speed should be increased
over 3500 RPM for 5 seconds to initiate the knock sensor malfunction recognition (On Board Diagnostic).
If an ignition timing point retarding value of one cylinder deviates from the others, the following malfunctions are possible:

Loose subassemblies
Corrosion on the harness connector
Engine damage (e.g. oil combustion with faulty piston)
If there are high ignition timing point retarding values on all cylinders of bank 1 or bank 2, the following malfunctions are
possible:
Corrosion on the harness connector display groups 015 and 016 Knock sensor tightening torque, 20 Nm (14 ft lb), not OK
Open circuit display groups 015 and 016 Knock sensor faulty
Pa
ge 276 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1