buttons AUDI A4 1996 B5 / 1.G AHA Engine Multiport Fuel Injection And Ignition System Workshop Manual

24-18

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -4- to select "Basic Setting" function 04, and
press -Q- button to confirm input.
System in Basic Settin
g
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -1- to input display group number 1 (001),
and press -Q- button to confirm input.
System in Basic Setting 1 1 2 3 4

Indicated on display (1-4 = display fields)
Note:
After selecting function 04, the ECM initiates the following:
EVAP canister purge regulator valve is closedA/C compressor is switched of
f
- Briefly raise engine speed (acceleration burst) and let engine run at idle
for another 2 minutes.
Pa
ge 23 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-20
If displayed values are OK (as specified):

-
Press button.
- Press buttons -0- and -6- to insert "End Output"
address word 06, and press -Q- button to
confirm input.

- Check readiness code page 01
-70
. If
Diagnostic Trouble Code (DTC) memory has
been erased, or ECM was disconnected,
generate new readiness code page 01
-73
.

Note:
The increased idle speed for vehicles with front-
wheel drive is achieved if there is voltage (from
terminal 15er) supplied to terminal 10 of the
Engine Control Module (ECM).
Pa
ge 25 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-23

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -2- to input display group number 32 (032),
and press -Q- button to confirm input.
Read Measuring Value Block 32 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 30 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-24

- Check learning values for Oxygen Sensor (O2S)
control before TWC (display fields 1-4):

Display fields

1 2 3 4
Display group 32: Oxygen Sensor (O2S) control learning values (before TWC)
Display xx.x % xx.x % xx.x % xx.x %
Indicates O2S control learning
value at idle (additive)
(before TWC)
Bank 1, Sensor 1 O2S control learning value at
part load (multiplicative)
(before TWC)
Bank 1, Sensor 1 O2S control learning
value at idle (additive)
(before TWC)
Bank 2, Sensor 1 O2S control learning value at
part load (multiplicative)
(before TWC)
Bank 2, Sensor 1
Range -25.0 to +25.0 % -25.0 to +25.0 % -25.0 to +25.0 % -25.0 to +25.0 %
Specified
value -10.0 to +10.0 %
(can vary slightly) -10.0 to +10.0 %
(can vary slightly) -10.0 to +10.0 %
(can vary slightly) -10.0 to +10.0 %
(can vary slightly)
If not as specified Evaluation of display group 32, page 24
-27

If displayed values are OK (as specified):

- Press -C- button.

- Press buttons -0-, -3- and -3- to input display
group number 33, and press -Q- button to
confirm input.
Pa
ge 31 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-26

Continuation
If the value in either display field 1 or 3 is NOT
OK, or if the value does not fluctuate by at least 2
%:

- Road test to condition oxygen sensor(s)
(eliminate possible contamination) and repeat
test.
If the value in either display field 1 or 3 is still
NOT OK, or if it still does not fluctuate by at least
2 %:

- Check Oxygen Sensor (O2S) heater(s) page
24
-34
.
If the value in either display field 1 or 3 remains
constant:

- Check oxygen sensor voltage(s) (display fields 2
and 4).

-
Press button.
- Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
input.

Pa
ge 34 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-35

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -0- to input display group number 40 (040),
and press -Q- button to confirm input.
Read Measuring Value Block 40 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 46 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-36

- Compare display and specified values (display
fields 1 and 2):

Display fields

1 2 3 4
Display group 40: Oxygen Sensor (O2S) heating (before and after TWC)
Display
xx.x
Htg.bC.ON/Htg.bC.OFF
xx.x
Htg.aC.ON/Htg.aC.OFF
Indicates Resistance of O2S heater
(before TWC)
(B1-S1 and B2-S1) O2S heater ON
or
O2S heater OFF
(before TWC)
(B1-S1 and B2-S1) Resistance of O2S heater
(after TWC)
(B1-S2 and B2-S2) O2S heater ON
or
O2S heater OFF
(after TWC)
(B1-S2 and B2-S2)
Range
0.0 - 65.0
--- --- ---
Specified value
2.4 - 9.2
Htg.bC.ON --- ---

If not as specified page 24
-37
, Continuation
--- ---
If displayed values are OK (as specified):

-
Press button.
-
Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
Pa
ge 47 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-43

Function test

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -3- and -6- to input display group number 36 (036),
and press -Q- button to confirm input.
Read Measuring Value Block 36 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 56 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-53

Checking

- Connect VAG1551 or VAG1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) page 01
-8 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -4- and -0- to input display group number 40 (040),
and press -Q- button to confirm input.
Read Measuring Value Block 40 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 67 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1

24-54

- Compare display and specified values (display
fields 3 and 4):

Display fields

1 2 3 4
Display group 40: Oxygen Sensor (O2S) heating (before and after TWC)
Display
xx.x
Htg.bC.ON/Htg.bC.OFF
xx.x
Htg.aC.ON/Htg.aC.OFF
Indicates Resistance of O2S heater
(before TWC)
(B1-S1 and B2-S1) O2S heater ON
or
O2S heater OFF
(before TWC)
(B1-S1 and B2-S1) Resistance of O2S heater
(after TWC)
(B1-S2 and B2-S2) O2S heater ON
or
O2S heater OFF
(after TWC)
(B1-S2 and B2-S2)
Range --- ---
0.0 - 65.0
---
Specified value --- ---
2.4 - 9.2
Htg.aC.ON

--- --- If not as specified page 24
-55
, Continuation
If displayed values are OK (as specified):

-
Press button.
-
Press buttons -0- and -6- to select "End Output"
function 06, and press -Q- button to confirm
Pa
ge 68 of 166 Motronic Multi
port Fuel In
jection
(MFI
) and i
gnition s
ystem
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.24.1