service AUDI A4 1996 B5 / 1.G AHA Engine On Board Diagnostic Workshop Manual

01-7
Modes under address word 33: Mode 1: Transfer diagnostic data Ignition switched on -or- Engine running at idle
Mode 2: Transfer operating conditions Ignition switched on -or- Engine running at idle
Mode 3: Check DTC memory Ignition switched on -or- Engine running at idle
Mode 4: Erase diagnosis information Ignition switched on -or- Engine running at idle
Mode 5: Output of HO2S signals Ignition switched on -or- Engine running at idle
Mode 6: Transfer measuring values Ignition switched on -or- Engine running at idle
Mode 7: Check DTC memory Ignition switched on -or- Engine running at idle Under Address word 33, Modes 1-7 can be addressed.
Under Mode 1, individual measuring values can be displayed. Mode 1 is not recommended for use in an Audi Service
department, because these values can be displayed much more precisely using address word 01 and "Basic Setting"
function 04 or "Read Measuring Value Block" function 08.
Mode 2 shows the operating conditions under which the stored malfunctions were recognized.
With Mode 3, DTC memory is checked-with Mode 4, DTC memory is erased.
Mode 5 shows the statistical value of the oxygen sensors as mandated by law. As these values have no direct bearing on
oxygen sensor diagnosis, Mode 5 is of no particular value in an Audi Service department.
Under Mode 6, values can be checked for components and systems that are not continuously monitored.
Pa
ge 10 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-11

Notes:
If the ECM version that corresponds to the
vehicle is not displayed, replace ECM page
01
-68
. Incorrect ECM coding leads to:

Performance problems (e.g. jerky shifting,
abrupt load changes, etc.)
Increased fuel consumption
Elevated exhaust gas values
Reduction in transmission service life
Storage of non-existent malfunctions in DTC
memory
Necessary functions not being carried out
(oxygen sensor control, actuation of EVAP
canister system, etc.)

-
Press button to advance through program
sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
- Continue as specified in procedures for specific OBD functions.
Pa
ge 16 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1

01-13

4D0907551A 2.8L V6/5V MOTR HS D01 Coding 06051
WSC 00000

Indicated on display (ECM identification and coding, e.g. 06051)
-
Press button to advance through program sequence.
Rapid data transfer
HELP
Select function XX

Indicated on display
Notes:
The Motronic ECM -J220- only uses the code that has been entered after
the ignition has been switched off once. Incorrect coding leads to: - Press buttons -0- and -6- to select "End Output" function 06, and press
-Q- button to confirm input.
Performance problems (e.g. jerky shifting, abrupt load changes, etc.)Increased fuel consumptionElevated exhaust gas valuesStorage of non-existent malfunctions in DTC memoryReduction in transmission service life
Pa
ge 19 of 97 On Board Dia
gnostic
(OBD
)
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU03.01.1