checking oil AUDI A4 1996 B5 / 1.G APB Engine Lubrication System Components Workshop Manual

17-1


Lubrication system
components, removing and
installing

Notes:

If large quantities of metal particles or other
deposits (caused, for example, by partial
seizure of the crankshaft or connecting rod
bearings) are found in the engine oil when
performing repairs, clean the oil passages
thoroughly and replace the oil cooler in order to
prevent further damage from occurring later.
Always replace O-rings, gaskets and oil seals
when performing repairs.
The oil level must not be above the max. mark -
otherwise this can cause damage to the
catalytic converter. Markings Page 17
-67

Viscosity grades and oil specifications
Repair Manual, Maintenance

Oil capacities
Repair Manual, Maintenance

Checking oil pressure Page 17
-65

Pa
ge 1 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-30

Chain tensioner for oil pump, checking

The chain tensioner incorporates a leaf spring.
To check the spring tension, the lower section of
the oil pan must be removed.

- Remove bumper

Repair Manual, Body Exterior, Repair Group
63


- Move lock carrier to service position.

Repair Manual, Body Exterior, Repair Group
50


- Remove ribbed belt Page 13
-1 .

- Remove lower section of oil pan Page 17
-
26


If no spring tension can be felt and the chain is not being tensioned, this
means the chain tensioner is malfunctioning and must be replaced. - Insert a screwdriver between chain and chain tensioner and press
screwdriver against chain tensioner.
Pa
ge 31 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-65

Oil pressure and oil pressure switch,
checking


Note:
Servicing and checking function of oil pressure
warning lamp and buzzer:

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Test procedure

- Remove oil pressure switch (F1) and screw oil pressure switch into
tester.
- Screw tester into oil pan in place of oil pressure switch.
- Connect brown wire of tester to ground (GND) (-).
- Using test leads from VAG 1594, connect diode test lamp VAG 1527
between positive battery terminal (+) and oil pressure switch.
- Start engine and gradually increase engine speed.
LED should light up at 1.2...1.6 bar, otherwise replace oil pressure
switch.
- Increase engine speed further.

At 2000 RPM and an oil temperature of 80 C oil pressure should be at
least 2.0 bar.
Pa
ge 71 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-67

Oil level, checking


Test conditions

Oil temperature above 60 C.

Vehicle level.
The vehicle must be standing on level
ground when checking the oil level. Wait for
a few minutes after switching off the engine
to allow the oil to flow back into the oil pan.

Test sequence

- Pull out dipstick, wipe off with a clean cloth and
insert it again as far as it will go.

- Pull out dipstick again and read oil level.
Pa
ge 73 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1