sensor AUDI A4 1996 B5 / 1.G ATQ Engine Electronic Engine Power Control Checking User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A4, Model: AUDI A4 1996 B5 / 1.GPages: 41, PDF Size: 0.21 MB
Page 25 of 41

24-151
Notes:
The reason why the value indicated in display
field 1 climbs, while the value indicated in
display field 2 decreases, has to do with the fact
that the potentiometers (angle sensors) in the
throttle valve control unit run in opposite
directions.
This means that the voltage tap of angle sensor
1 runs from 0 to 5 volts. (The more the throttle
valve is opened, the larger the voltage; percent
indication climbs).
The voltage tap of angle sensor 2 runs from 5
to 0 volts. (The more the throttle valve is
opened, the lower the voltage; the percentage
decreases).
If indications do not resemble description:
- Check voltage supply and wire connections of
throttle valve control module Page 24
-152
.
Pay particular attention to harness connectors
that could be loose or corroded.
- Check accelerator pedal position sensor Page
24
-154
.
Pa
ge 25 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 28 of 41

24-154
Throttle Position (TP) sensor, checking
Special Tools and Equipment
VAG1526A
VAG1594A
VAG1598/31
VAS5051 with VAG5051/1
- or
VAG1551 with VAG1551/3B
Pa
ge 28 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 29 of 41

24-155
Both the Throttle Position (TP) sensor -G79- and
the Sender -2- for accelerator pedal position -
G185- are located at the accelerator pedal and
communicate the driver's intentions to the ECM
completely independently of each other. Both
sensors are stored in one housing.
Test sequence
- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .
Ignition must remain switched on for this.Rapid data transfer
HELP
Select function XX
When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input display group number XXX
When indicated on display:
- Press buttons -0-, -6- and -2- to select "display group number 062" and
press -Q- button to confirm input.
Read Measuring Value Block 62
1
2
3
4
Indicated on display:
- Check specified values for E-gas potentiometer voltages in display
fields 3 and 4.
Pa
ge 29 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 30 of 41

24-156
Display fields
1 2 3 4
Display group 062: E-Gas potentiometer voltages
Display xx % xx %
xx %
xx %
Indicated Throttle valve angle
(angle sensor 1) Throttle valve angle
(angle sensor 2) Sensor for
Pedal position Sensor 2 for
Pedal position
Functional range 0 to 100 % 0 to 100 %
0 to 100 %
0 to 50 %
Specified value 3 to 93 % 97 to 3 %
12 to 97 %
(Idle value: 8 to 18 %) 4 to 49 %
(Idle value: 3 to 13 %)
Note:
Engine Control Module (ECM) calculates the
voltage values of the angle sensors in percent
relative to 5 volts and displays these percentage
values. (5 volts supply voltage represents 100
%).
- Observe display field 3 and 4.
- Slowly depress accelerator pedal completely.
Percent indication in display field 3 must rise
uniformly. The tolerance range 12 to 97% is not
used completely during this.
Pa
ge 30 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 32 of 41

24-157
Note:
The indicated value in display field 3 must always
be about twice as large as the value in display
field 4.
If indications do not resemble description:
- Check voltage supply and wire connections of
sensor for accelerator pedal position Page
24
-158
.
Pa
ge 32 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 33 of 41

24-158
Checking voltage supply of Throttle Position
(TP) sensor
- Remove driver-side storage compartment.
Repair Manual, Body
-Interior, Repair Group
68; Instrument Panel; Removing Driver
-Side
Storage Compartment
- Disconnect harness connector for accelerator
pedal position sensor.
- Switch ignition on.
If specified values are obtained: - Connect multimeter for voltage measurement as follows:Harness connector
Terminal
Specified value
1 + Ground (GND) about 5 V
1 + 5 about 5 V
2 + Ground (GND) about 5 V
2 + 3 about 5 V
Pa
ge 33 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 34 of 41

If specified values are not obtained: - Also check signal wires.
- Check wire connections from Engine Control Module (ECM) to sensors
for accelerator pedal position.
Pa
ge 34 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 36 of 41

24-160
If no malfunctions are found in wires:
- Replace accelerator pedal position sensor.
Repair Manual, Fuel Supply System, Repair
Group 20
Note:
For vehicles with automatic transmission, the
kick down function must be learned Page 24
-
161
.
Pa
ge 36 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 37 of 41

24-161
Kick down function, adapting
If the sensor for accelerator pedal position or the
Engine Control Module (ECM) is replaced on a
vehicle with automatic/variable transmission, the
kick down function must be learned by the ECM.
Special Tools and Equipment
Requirements
Procedure
VAS5051 with VAG5051/1
orVAG1551 with VAG1551/3BNo DTCs in DTC memory, check DTC memory Page 01
-15
.
Engine not running, ignition switched on.
- Connect VAS5051 tester or VAG1551 scan tool and select the control
module for engine electronics using "address word" 01 Page 01
-9 .
Ignition must remain switched on for this.
Pa
ge 37 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5
Page 39 of 41

24-163
Display fields
1 2 3 4
Display group 063: Kick down function, adapting
Display xx % xx %
Kick
down ---
Indicated Sensor 1 for
Pedal
position Sensor 2 for
Pedal
position Kick
down Adaptation condition
Functional
range 0 to 100 % 0 to 50 %
Kick
down operate
ADP in progress
ADP OK
ADP ERROR
Specified value 12 to 97 % 4 to 49 %
Kick
down ADP OK
Notes
If "ADP ERROR." is displayed: Check DTC memory
Page 01
-15
.
Notes:
The abbreviation "ADP" in display field 4 stands for Adaptation.
"ERROR" can be indicated, for example, if the accelerator pedal is not immediately pressed in response to a request by
the tester or if the accelerator pedal is released while adaptation is running despite the fact that adaptation is not yet
Pa
ge 39 of 41 Electronic en
gine
power control
(E-Gas
), checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.5