cooling AUDI A4 1996 B5 / 1.G AWM Engine Cooling System Components Workshop Manual

19-1


Cooling system components,
removing and installing

WARNING!

Hot steam can escape when opening the cap
on the expansion tank: Cover the cap with a
cloth and open carefully.

Note:

When the engine is warm the cooling system is
under pressure. If necessary release pressure
before beginning repair work.
Secure all hose connections with the correct
hose clips (same as original equipment):

Parts Catalog

Hose clip pliers VAG 1921 are recommended
when installing spring type clips.
Replace all gaskets and seals.
The arrow markings on the coolant lines and on
the ends of the hoses must be aligned with
each other.
Pa
ge 1 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-2


Cooling system diagram

1 -
Radiator
Removing and installing Page 19
-26
After replacing, fill with fresh coolant
2 -
Upper coolant line
3 -
Thermostat Removing and installing coolant pump
Page 19
-12

Checking Page 19
-22
4 -
Coolant pump
Removing and installing Page 19
-12
Check for ease of movement
5 -
Turbocharger
Pa
ge 3 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-4


Cooling system, draining and filling

Special tools and equipment

Adapter 1274/8
Line VAG 1274/10
Drip tray VAG 1306
Hose clamp pliers VAG 1921
Special tool T10007
Pa
ge 5 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-7

Filling

Note:

The cooling system is filled all year round with a
mixture of water and an antifreeze/corrosion
protection agent.
Only use coolant additive G 012 A8 D meeting
specification TL VW 774 D. Identification color:
red

CAUTION!

G 012 A8 D and other coolant additives
cannot be mixed. Otherwise, serious damage
to the engine may result.
If the fluid in the expansion tank is brown, this
means G 012 A8 D has been mixed with
another type of coolant. In this case, flush out
the cooling system and fill with fresh coolant. To
flush the system, fill it with clean water and run
the engine for about 2 minutes. This should
remove as much of the old coolant as possible.
G 012 A8 D and coolant additives marked
"meeting specification TL VW 774 D" prevent
frost and corrosion damage and stop scaling
while at the same time raising the boiling point
of the coolant. For these reasons the cooling
Pa
ge 8 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-8

Because of its high boiling point, the coolant
improves engine reliability under heavy loads,
particularly in countries with tropical climates.
Protection against frost must be assured to
about -25 C (in arctic climatic countries to
about -35 C).

The coolant concentration must not be reduced
by adding water, even in warmer seasons and
in warmer countries. The anti-freeze ratio must
be at least 40 %.
If greater frost protection is required in very cold
climates, the amount of G 012 A8 D can be
increased, but only up to 60% (this gives frost
protection to about -40 C). Otherwise, frost
protection is reduced again and cooling
effectiveness is also reduced.

Only use clean drinking water for mixing the
coolant.
If radiator, heat exchanger, cylinder head or
cylinder head gasket is replaced, do not reuse
old coolant.
Use special tool T10007 to check frost
protection of coolant additive G012 A8 D in
Pa
ge 10 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

cooling system.
Pa
ge 11 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-27


WARNING!
Hot steam can escape when opening the cap on the expansion tank:
Cover cap with a cloth and open carefully. - Disconnect cooling lines for power steering hydraulic fluid -arrows-.
- Open cover of coolant expansion tank
- Place drip tray VAG 1306 below engine.

- Turn drain screw -arrow- on radiator counter-clockwise. If necessary,
install a drain hose on connection.
Pa
ge 30 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

Component
Nm
Condenser to radiator 10
Cooling lines to radiator 10
Hose clamps for coolant hoses 2
Pa
ge 35 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1

19-32


Cooling system, checking for leaks

Special tools and equipment

VAG 1274
Adapter 1274/8
Adapter 1274/9
Pa
ge 36 of 38 Coolin
g system com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.19.1