wheel bolt torque AUDI A4 1996 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1996, Model line: A4, Model: AUDI A4 1996 B5 / 1.GPages: 20, PDF Size: 0.39 MB
Page 3 of 20
13-49
8 -
Securing bolt for dual-mass flywheel or
drive plate
Always replaceTightening torque for dual mass flywheel
Page 13
-63
Tightening torque for drive plate (vehicles
with automatic gearbox) Page 13
-66
9 -
Intermediate plate
Must be located on dowel sleevesDo not damage/bend when assembling
Pa
ge 3 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 6 of 20
13-52
Removing
Engine in vehicle
Lock carrier must be in service position
Page 13
-1 .
- Remove toothed belt Page 13
-40
.
- Unbolt stop for torque reaction support -arrows-.
- Remove toothed belt sprocket from crankshaft. To do this, counter hold
sprocket with 3415.
Pa
ge 6 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 9 of 20
13-55
- Replace central bolt for toothed belt sprocket.
Note:
Tightening torque 1) Replace bolt 2) 90 corresponds to a quarter turn - Remove crankshaft toothed belt sprocket. To do this, counter-hold
toothed belt sprocket with 3415. Contact surface between sprocket and crankshaft must be free of oil.Do not oil bolt for crankshaft sprocket.
- Install toothed belt (adjust valve timing) Page 13
-44
.
- Install ribbed belt and tensioner for ribbed belt Page 13
-20
.
- Install lock carrier Page 13
-1 .
Component
Nm
Toothed belt sprocket to crankshaft
90 + 90
1)2)
Pa
ge 9 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 11 of 20
13-57
Removing
Engine in vehicle
Lock carrier must be in service position
Page 13
-1 .
- Remove toothed belt Page 13
-40
.
CAUTION!
The air conditioner refrigerant circuit must
not be opened.
- Disconnect A/C compressor from bracket and
secure to body with wire.
- Unbolt bracket for A/C compressor -Item 5 -,
Page 13
-15
- Unbolt stop for torque reaction support -arrows-.
Pa
ge 11 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 17 of 20
13-63
Installing
Installation is carried out in the reverse order or
removal; note the following:
- Replace bolts.
Tightening torque
Component
Nm
Dual-mass
flywheel 22.5 mm
1) 60 + 90
2)
on crankshaft
43 mm
1)
60 + 180
3)
1) Bolt length
2) 90 corresponds to a quarter turn
3)180 =
1/2 turn
Pa
ge 17 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 19 of 20
13-65
Installing
- Place drive plate in position with shim -2- and washer -1-. Lug -arrow-
must face towards torque converter.
- Insert at least 3 old securing bolts and tighten to 30 Nm.
- Measure distance -a- at three points and calculate average value.
Specified value: 18.9 to 20.5 mm
Pa
ge 19 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2
Page 20 of 20
13-66
If nominal value is exceeded:
If specified value is attained:
Tightening torque 1) 90 corresponds to a quarter turn - Remove drive plate again and fit without shim -2-. Retighten bolts to 30
Nm.
- Measure distance again.
- Install new bolts and tighten.Component
Nm
Drive plate to crankshaft
60 + 90
1)
Pa
ge 20 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2