wheel AUDI A4 1996 B5 / 1.G Brakes Read Mesure Value Block 08 Workshop Manual

01-142
Test table: display group 1
Notes:

Display fields 1 through 4 show the current wheel circumference speeds in km/h. These are calculated by the ABS control
module -J104- on the basis of the signals received from the wheel speed sensors. If one of the display fields shows no
reading, proceed as for DTCs 00283, 00285, 00287, 00290 "ABS Wheel Speed Sensor" Diagnostic Trouble Code (DTC)
table
In order to check whether wheel speed sensors are properly allocated to each wheel, the vehicle must be raised. On
vehicles with manual transmission put the gear shift lever in neutral. On vehicles with automatic transmission move the
selector lever to position "N". Turn appropriate wheel by hand. Remaining drive wheels must be secured against turning.
When a vehicle is accelerated uniformly on a dry surface, the displayed value will increase continuously by whole
numbers; e.g. 6 km/h, 7 km/h, 8 km/h ... . The difference between displayed values 1-4 should not be more than 1 km/h
(error from out-of-round wheels). If the values jump, for instance from ...6km/h, 7 km/h, to 12 km/h...or if the difference
between the displayed values is greater than 1 km/h, then check the installation of the wheel speed sensors and rotors. Repair Manual, Brake System, Repair Group 45

Read measuring value block
1
Indicated on display
1 to 19
1)
km/h 1 to 19
1)
km/h
1 to 19
1)
km/h 1 to 19
1)
km/h


Right rear ABS wheel speed sensor

Left rear ABS wheel speed sensor

Right front ABS wheel speed sensor
Pa
ge 4 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

Left front ABS wheel speed sensor 1) On Board Diagnostic (OBD) is terminated by the ABS control module -J104- if road speed exceeds 19 km/h.
Pa
ge 5 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12

01-146
Test table: display group 3 Read measuring value block
3
Indicated on display
60 to
8000
1 RPM 0 to 100
%
0 or 1
---


Traction control (ASR) button: (Only for vehicles equipped with ASR)

0 Traction control button not operated. 1 The traction control button is operated, operational condition of ASR alternates, i.e. "ASR
OFF" and "ASR ON".
- Check traction control button if there are deviations. Carry out "Electrical test", step 11 page 01
-
166
.

Actual engine torque (AET): (Only for vehicles equipped with ASR)
0% vehicle is in deceleration mode.20% - 30% represents engine idle.100% engine is offering its maximum torque.
- If no indication is displayed, proceed according to DTC 00647 "ABS-ASR engine electrical connection 2".
Diagnostic Trouble Code (DTC) table
Engine speed: (Only for vehicles equipped with ASR)

Engine speed is displayed in increments of 60 RPM, starting at 60 RPM.
- If no indication is displayed, proceed according to DTC 00529 "Wheel speed information missing. No signal". Diagnostic
Pa
ge 9 of 13 Read Measurin
g Value Block
(function 08
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.12