coolant AUDI A4 1997 B5 / 1.G APB Engine Valve Gear Service Workshop Manual

15-14

Removing oil seal at Hall sensor (left cylinder
head)

Note:
Leave coolant hoses connected. - Detach coolant reservoir -arrows- and move clear to side.
- Unplug connector from coolant level monitor.
- Move wiring harness clear at bulkhead.

- Unbolt bracket -arrows- for plug connectors on bulkhead and move
clear to side.
Pa
ge 14 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-18


Note:
Leave coolant hoses connected. - Remove coolant reservoir -arrows- and move it clear to the side.
- Unplug connector from coolant level monitor.
- Move wiring harness clear at bulkhead.

- Unbolt bracket -arrows- for plug connectors on bulkhead and move
clear to the side.
- Unbolt Hall sensor housing (10 Nm).
- Remove bolt securing Hall sensor rotor (20 Nm) and carefully lever off
rotor using a screwdriver.
Pa
ge 18 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-23


Note:
Leave coolant hoses connected. - Remove coolant reservoir -arrows- and move it clear to the side.
- Unplug connector from coolant level monitor.
- Remove cover panel from cylinder head cover (cylinder bank 4 - 6).

Note:
Plug lower section of intake line. - Release hose clamp -arrow-.
- Remove intake line -1-.
- Disconnect hose -2-.
- Detach water line -3-.
Pa
ge 23 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-36


- Unbolt rear left toothed belt guard -arrows-.
- Detach intake manifold using special tool 3249.

- Unbolt cylinder head lifting bracket with coolant line -arrows- from
cylinder head.
Pa
ge 36 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-38


Note: - Unbolt coolant line at front of cylinder head -arrows-.
- Unbolt cylinder head cover.
- Loosen and remove cylinder head bolts in opposite sequence to
tightening sequence using special tool 3452 (Polidrive).
- Carefully lift off cylinder head.

Use special tool 3452 together with a normal commercial 10 mm socket
when removing and installing.
Pa
ge 38 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-39

Installing

Notes:

Do not allow any oil or coolant to remain in the
blind holes for the cylinder head bolts in the
cylinder block.
Replace cylinder head bolts.
Connecting vacuum hoses Page 10
-28
.
When installing a new cylinder head:

- Screw in centering pin for intake manifold.
The cylinder head supplied as a replacement
part can be used on both sides (left or right). But
a sealing cap (core plug) must be installed in the
front end of the cylinder head in each case.

- Coat outside circumference of sealing cap (core
plug) with sealant AMV 188 001 02.

- Using drift VW 295, knock in sealing cap (core plug) until outside rim is
flush with end of chamfer in cylinder head.
Pa
ge 39 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-53

Installing

Notes:

Do not allow any oil or coolant to remain in the
blind holes for the cylinder head bolts in the
cylinder block.
Install new cylinder head bolts.
Connecting vacuum hoses Page 10
-28
.
When installing a new cylinder head:

- Screw in centering pin for intake manifold.
The cylinder head supplied as a replacement
part can be used on both sides (left or right). But
a sealing cap (core plug) must be installed in the
front end of the cylinder head in each case.

- Coat outside circumference of sealing cap (core
plug) with sealant AMV 188 001 02.

- Using drift VW 295, knock in sealing cap (core plug) until outside rim is
flush with end of chamfer in cylinder head.
Pa
ge 53 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-59


Note:
Leave coolant hoses connected. - Remove coolant reservoir -arrows- and move it clear to the side.
- Unplug connector from coolant level monitor.
- Remove cover panel from cylinder head cover (cylinder bank 4 - 6).

Note:
Plug lower section of intake line. - Release hose clamp -arrow-.
- Remove intake line -1-.
- Disconnect hose -2-.
- Detach water line -3-.
Pa
ge 59 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-66

Camshaft adjustment, checking function


Special tools and equipment

Test requirement:
WARNING!
VAS 5051 with VAG 5051/1
orVAG 1551 with VAG 1551/3ACoolant Temperature at least 80 C. During a road test in an airbag-equipped vehicle, test equipment
must always be fastened to and operated from the rear seat by a
second technician. When driving or riding in an airbag-equipped vehicle, NEVER hold
the scan tool or other test equipment in your hands or lap while in
motion. Objects between you and the airbag increase the risk of
injury in an accident.
Pa
ge 66 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1

15-88

Hydraulic lifters, checking


Notes:

Replace malfunctioning lifters completely (lifters
cannot be adjusted or repaired).
When new lifters have been installed the engine
must not be started for about 30 minutes
(otherwise valves will strike pistons).
Irregular valve noises when starting engine are
normal.

- Start engine and run until coolant temperature
reaches approx. 80 C.

- Increase engine speed to about 2500 RPM for
approx. 2 minutes: if necessary, perform road
test.
If the hydraulic lifters are still noisy, locate
malfunctioning lifters as follows:

- Remove cylinder head cover.

- Rotate crankshaft clockwise by turning securing
bolt for toothed belt sprocket until cams of lifters
to be checked are pointing upward.
Pa
ge 89 of 99 Valve
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.15.1