ignition AUDI A4 1997 B5 / 1.G ATQ Engine Additional Signals Testing Workshop Manual

24-170

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

- Connect VAG1527B voltage tester to sockets 3
(B+) and 54 (VSS) of VAG1598/31 test box.

- Switch ignition on and turn front left wheel by
hand.


LED must blink (very brief blink signal).
If LED does not blink:

- Check the following wire connection for open
circuit and short circuit to Ground (GND) and B+:

Test box
VAG1598/31
Socket
Instrument cluster

Terminal
54 Electrical Wiring Diagrams,
Troubleshooting & Component
Locations binder

- Repair open circuit or short circuit if
necessary.
Pa
ge 6 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-178

Brake light switch and brake pedal
switch, checking


Note:
For safety reasons, the instruction from the
accelerator pedal sensor (potentiometer) to the
ECM to open the throttle valve is suppressed
when brake is being operated. This requires the
brake light switch signal and also the brake pedal
switch signal in the control module.
If brake pedal is operated with accelerator pedal
constantly depressed, engine is immediately
regulated down to idle speed. A faulty switch can
lead to undesired regulation.

Test sequence

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Ignition must remain switched on for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Pa
ge 16 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-181
If specified values are not obtained:

- Check adjustment of switch or

- Replace brake light switch / brake pedal
switch.
If specified values are obtained:

Checking voltage supply

- Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Chassis Ground (GND)

LED must light up.
- Switch ignition on.
Harness connector
Terminal
Measure to
3 Chassis Ground (GND)

LED must light up.
Pa
ge 21 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-183

Clutch vacuum vent valve switch -F36-,
checking


Note:
This signal helps prevent excessive RPM
oscillations and tip-in shocks when clutch is
disengaged and is required for the cruise control
system.

Test sequence

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Ignition must remain switched on for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input displa
y group number XXX

When indicated on display:
- Press buttons -0-, -6- and -6- to select "display group number 066" and
press -Q- button to confirm input.
Read Measuring Value Block 66

Indicated on display:
Pa
ge 24 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-186
If specified value is obtained:

Checking voltage supply

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Chassis Ground (GND)
- Switch ignition on.

LED must light up.
- Check wire connection from terminal 1 of connector to fuse for open
circuit and short circuit to Ground (GND):
Pa
ge 29 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-191

Test requirement:

Control module coding OK Page 01
-71
.

Test sequence

- Switch ignition off.

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

- Check the following wire connection for open
circuit and short circuit to Ground (GND) and B+:

Test box
VAG1598/31
Socket
ABS control module (w/EDL)
-J104-
Terminal
74 Electrical Wiring Diagrams,
Troubleshooting & Component
Locations binder
If no malfunctions are found in wire:

- Replace ABS control module.
If the malfunction is indicated again after
Pa
ge 34 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

9 .

Ignition must remain switched on for this.
Pa
ge 37 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-196

Example 1:

From the DTCs stored in the memories, you have determined that control
module 1 is not communicating with control modules 2 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2Missing signal from control module 3
2 Missing signal from control module 1
3 Missing signal from control module 1
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 1 if no malfunctions can be found in the bus
wires.
Pa
ge 41 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-197

Example 2:

From the DTCs stored in the memories, you have determined that control
module 2 is not communicating with control modules 1 and 3.
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder Control module
DTCs stored in DTC memories:
1
Missing signal from control module 2
2 Missing signal from control module 1Missing signal from control module 3
3 Missing signal from control module 2
- Switch ignition off.
- Disconnect the control modules connected across the bus wires and
check the bus wires for an open circuit. - Replace control module 2 if no malfunctions can be found in the bus
wires.
Pa
ge 42 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6

24-198

Example 3:
Using the DTCs stored in the memories, you
have determined that none of the control
modules are sending or receiving signals.

Control
module
DTCs stored in DTC
memories:
1
Powertrain databus faulty
2 Powertrain databus faulty
3 Powertrain databus faulty

- Switch ignition off.

Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Disconnect the control modules connected across the bus wires and
check bus wires for a short circuit to B+ and Ground (GND).
Pa
ge 43 of 44 Additional si
gnals, testin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.6