buttons AUDI A4 1997 B5 / 1.G ATQ Engine Motronic Injection System Servicing Workshop Manual

24-26

Notes:

Idle speed cannot be adjusted.
Idle speed is checked during basic setting of
the engine.
During basic setting, the Evaporative Emission
(EVAP) canister purge regulator valve (EVAP
valve -N80-) is closed and the A/C compressor
is switched off

Test sequence

- Check DTC Memory Page 01
-15
. There must
not be any DTCs stored, repair malfunctions if
necessary, erase DTC memory, switch engine
off and start again, road test vehicle and check
DTC memory again as a control measure.

- Let engine continue to run at idle.

CAUTION!

The electric cooling fan must not run. Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
button to confirm input.
Pa
ge 28 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-27

Basic Settin
g
Q
Input display group number XXX

When indicated on display:
- Press buttons -0-, -5- and -6- to select "display group number 056" and press -Q-
button to confirm input.
System in Basic Setting 56
1
2
3
4

When indicated on display:
- Check whether the engine speed in display field 1 (actual engine speed) is within
tolerated range.

Display fields

1 2 3 4
Display group 056: Idle stabilization with engine at idle and operating temperature
Display
xxx /min
xxx /min x.x % X X X X X
Indicated
Engine speed (actual)
Engine speed
(specified) Idle control
Torque
change Operating conditions
Specified
value 720 to 820 RPM
1)
630 to 730 RPM 2) 770 RPM
1)
680 RPM 2) -5 to 5 % 0 0 0 0 0
Notes
If specified value is not obtained
Page 24
-29

Significance of
numbers
Page 24
-29

1) Front Wheel Drive Vehicles
Pa
ge 29 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-57

Test requirements:

Coolant Temperature at least 80 C.

Electrical consumers switched off (radiator
fan must NOT run during test).
A/C switched off.
Fuse for Mass Air Flow (MAF) sensor OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder

Checking function

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Engine must run at idle for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
-
Press buttons -0- and -4- to select "Initiate basic setting" and press -Q-
Pa
ge 67 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-58

Basic Settin
g
Q
Input display group number XXX

When indicated on display:
- Press buttons -0-, -0- and -2- to select "display group number 002" and press -Q-
button to confirm input.
System in Basic Setting 2
1
2
3
4

When indicated on display:
- Check specified values for load detection in display fields 3 and 4.

Display fields

1 2 3 4
Display group 002: Air mass taken in with engine at idle and operating temperature
Display xxx /min xx.x %
x.x ms
xxx.x g/s
Indicated Engine speed
(RPM) Load
mean injection time
Air mass
Functional
range 630 to 6800
RPM 12 to 100
% 1.0 to 20.0 ms
1.0 to 150 g/s
Specified
value 720 to 820
RPM
1)
630 to 730
RPM2) 12.0 to
26.0 % 1.0 to 4.0 ms
1.0 to 5.0 g/s
Notes --- ---
If specified value is not obtained:
Evaluation display field 3 Page 24
-
59

If specified value is not obtained:
Evaluation display field 4 Page 24
-
60

1) Front Wheel Drive Vehicles
Pa
ge 69 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-65

Test sequence

- Connect VAS5051 tester or VAG1551 scan tool
and select the control module for engine
electronics using "address word" 01 Page 01
-
9 .

Engine must run at idle for this.Rapid data transfer
HELP
Select function XX

When indicated on display:
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read Measurin
g Value Block
Q
Input display group number XXX

When indicated on display:
- Press buttons -0-, -0- and -1- to select "display group number 001" and
press -Q- button to confirm input.
Read Measuring Value Block 1
1
2
3
4

Indicated on display: (1 thru 4 display fields) - Make note of engine speed in display field 1.
- Spray intake system parts with engine leak detection spray in a
systematic manner.
Pa
ge 77 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-66
If engine speed does not change:

-
Press button.Rapid data transfer
HELP
Select function XX

Indicated on display (function selection):
If engine speed decreases:
-
Press button.- Press buttons -0- and -6- to select "End output" and press -Q- button to
confirm input.
- Switch ignition off.
- Check sprayed part of intake system for leaks, and eliminate the error.
Pa
ge 78 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1