AUDI A4 1997 B5 / 1.G ATW Engine Motronic Fuel Injection Syst

System in basic setting 2
1
2
3
4

- Check specified values for load detection.
Pa
ge 71 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-62


Display fields

1 2 3 4
Display group 002: Air mass taken in with engine at idle and operating temperature
Display xxx /min xxx %
xx.x ms
xxx.x g/s
Indicated Engine speed (RPM) Load
mean injection time
Air mass
Specified value FWD: 740 to 860 RPM
AWD: 800 to 920 RPM 15 to 33 %
1.0 to 4.0 ms
2.0 to 4.5 g/s
Note --- ---
If specified value is not obtained: Evaluation Page 24
-63

If specified value is obtained:

-
Press button.Rapid data transfer
HELP
Select function XX

Indicated on display (function selection):
Pa
ge 72 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-63
Evaluation display group 002 Display field:
3
Possible cause
Corrective action
less than 1.0
ms
Smaller values are only possible when driving in
deceleration mode
larger than 4.0
ms Engine under load due to power accessories.- Reduce load (A/C system/power
steering/generator)

Poor idle (does not run on all cylinders)- Check spark plugs.
- Check fuel injectors Page 24
-38
.


Throttle valve control module - J338- faulty- Check throttle valve control module
Page 24
-120

Display field:
4
Possible cause
Corrective action
smaller than
2.0 g/s
large false air mass between intake manifold and Mass Air
Flow (MAF) sensor
Voltage supply of Mass Air Flow (MAF) sensor or wire
connections to Engine Control Module (ECM) - Check intake system for leaks (false
air) Page 24
-68
.
- Check voltage supply and wire
connections Page 24
-64

larger than 4.5
g/s
Engine under load due to power accessories.- Reduce load (A/C system/power
steering/generator)

Voltage supply of Mass Air Flow (MAF) sensor or wire
connections to Engine Control Module (ECM) - Check voltage supply and wire
connections Page 24
-64

Pa
ge 73 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-64

Voltage supply for Mass Air Flow (MAF)
sensor, checking

Test requirements:

Fuse for Mass Air Flow (MAF) sensor OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations

Fuel Pump (FP) relay OK; checking Page 24
-53
.

Note:
Voltage is supplied to Mass Air Flow (MAF)
sensor from Fuel Pump (FP) relay.

- Disconnect connector from Mass Air Flow (MAF)
sensor.

- Connect multimeter for voltage measurement as follows.Harness connector
Terminal
Measure to
2 Engine Ground (GND)
Pa
ge 74 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

- Operate starter briefly (engine can also start).

Specification: approx. battery voltage
Pa
ge 75 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-65
If specified value is not obtained:

- Check wire connection from terminal 2 of
connector to Fuel Pump (FP) relay via fuse for
open circuit and short circuit to Ground (GND):

Electrical Wiring Diagrams, Troubleshooting &
Component Locations
- Repair open circuit or short circuit if
necessary.

Note:
Ground (GND) from the ECM is present at terminal 3 of connector.
If specified value is not obtained: - Connect multimeter to terminal 2 and terminal 3 of connector for
voltage measurement.
- Operate starter briefly (engine can also start).

Specification: approx. battery voltage
- Check wire connections Page 24
-67
.
Pa
ge 76 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-66


If specified value is not obtained: - Connect multimeter to terminal 3 and terminal 4 of connector for
voltage measurement.

Specification: about 5 V
- Check wire connections Page 24
-67
.
Pa
ge 77 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-67

Check wire connections for Mass Air Flow
(MAF) sensor

Note:
Signal wire is also checked during wire test.

- Connect VAG1598/31 test box at wiring harness
to Engine Control Module (ECM), do not connect
ECM Page 24
-19
.

If wire connection is OK: - Check following wire connections for open circuit and short circuit to
Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
3 27
4 53
5 29
- Repair open circuit or short circuit if necessary.
- Also check all wires for short circuit to each other.
- Replace Mass Air Flow (MAF) sensor -G70-.
Pa
ge 78 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-68

Intake system, checking for leaks
(unmetered air)


Special tools and equipment

Note:
VAS5051 with VAG5051/1
orVAG1551 with VAG1551/3AEngine leak detection spray G 001 800 A1The negative pressure in the intake system sucks in the leak detection
spray with the unmetered air. Leak detection spray decreases ignition
quality and performance of the fuel mixture. This causes a reduction in
engine speed and a sharp increase of CO content. It is absolutely necessary to follow the safety precautions listed on the
can.
Pa
ge 79 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1

24-69

Test sequence

- Connect VAS5051 tester or VAG1551 scan tool
and select control module for engine electronics
using "address word" 01 Page 01
-10
. Engine
must run at idle.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read measurin
g value block
Q
Enter displa
y group number XXX

When indicated on display
- Press buttons -0-, -0- and -1- to select "display group number 001" and
press -Q- button to confirm input.
Read Measuring Value Block 1
1
2
3
4

Indicated on display(1 to 4 display fields)
If engine speed decreases: - Make note of engine speed in display field 1.
- Spray intake system parts with engine leak detection spray in a
systematic manner.
- Check sprayed part of intake system for leaks, and eliminate error.
Pa
ge 80 of 81 Motronic fuel in
jection s
ystem, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU06.24.1