child seat AUDI A4 1997 B5 / 1.G Seatbelts Workshop Manual

69-10



Lower belt webbing must be bolted to metal
stud -10- as shown in magnified area
Remainder of installation is reverse of removal
- After installing passenger side three-
point seat belt, check belt function for
child seat page 69
-37
.
Three-point seat belt must not be hindered
by cables, wires or dampening material etc
10 -
Metal stud in floor pan Anti-twist stop for belt webbing bracket
11 -
Anti-twist stop and reverse-mounting
protection for three-point safety belt
Pa
ge 14 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1

69-16


Note:
The igniter wire -11- must not be located near the
belt webbing. Vehicles with CD player and/or subwoofer or
similar:
- Remove side trunk trim page 70
-87
.
Vehicles with belt tensioners:
- Unclip igniter wire -11- at clip -10-.
- Detach harness connector for igniter wire
at clip -9-.
- Remove bolt -6- (1x).
- Detach seat belt against direction of
arrow.
Installing:
Make sure harness connector for igniter
wire -11- engages
- Clip igniter wire -11- into clip -10-.For vehicles with belt tensioner, check belt-
fastened sensor page 69
-38

After installing rear three-point seat belt,
check belt function for child seat page 69
-37

Pa
ge 20 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1

69-19



For vehicles with belt tensioner, check belt-
fastened sensor page 69
-38

After installing rear three-point seat belt, check
belt function for child seat page 69
-37

The three-point seat belt must not be hindered
by cables, wires or dampening material, etc
3 -
Bracket
4 -
Bolt
50 Nm (37 ft lb)
5 -
Bracket
6 -
Bolt 2.5 Nm (22 in. lb)It is not necessary to remove metal bracket
when removing belt
7 -
Three-point seat belt with belt tensioner
8 -
Clip
9 -
Clip
10 -
Igniter wire
Pa
ge 25 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1

69-27


LATCH system, "Lower Anchors and
Tethers for CHildren", installing,
removing, retrofitting (Sedan)

Rear upper tethers, installing
Note:
Mountings can be installed for three upper tether
attachment points.
- Remove rear shelf page 70
-83
.
1 -
Cover
2 -
Cap
- To install, attach at front and press in
direction of arrow and downward.
3 -
Bolt
23 Nm (17 ft lb)
4 -
Attachment point
5 -
Spacer
Pa
ge 33 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1

69-31

LATCH system, "Lower Anchors and
Tethers for CHildren", installing,
removing, retrofitting (Avant)


Rear upper tethers

Note:
Some A4 Avant models may require a seat back
change for rear top tether installation.

Rear upper tethers (Avant), retrofitting (
m.y. 1998)
To retrofit the child seat attachment point on
vehicles m.y. 1998, a backrest from m.y. 1999
or later must be installed.
- Remove old backrest.

Repair Manual Body Interior Repair Group 72



1/3 backrest

- Using sharp knife, carefully cut upholstery -1- at width of 30 mm
(dimension -B-) down to indentation -2- (dimension -A- = 195 mm when
measured from below).
Pa
ge 37 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1

69-33

Rear upper tethers (Avant), retrofitting (
m.y. 1998) To retrofit the child seat upper tether points on
vehicles m.y. 1998, a backrest from m.y. 1999
or later must be installed.
- Remove old backrest.

Repair Manual Body Interior Repair Group 72



1/3 backrest

2/3 backrest
All backrests - Using sharp knife, carefully cut upholstery -1- at width of 30 mm
(dimension -B-) down to indentation -2- (dimension -A- = 195 mm when
measured from below).
- Using sharp knife, carefully cut upholstery at reinforcements.
- Install new panel on backrest.

Note original color and cargo net version.
Pa
ge 39 of 41 Seat belts11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.BD03.69.1