lock AUDI A4 1998 B5 / 1.G 01W Transmission Remove And Install Workshop Manual

34-26


Note:
If 3282 transmission support is not available, the transmission can be
removed and installed using the VAG1383A transmission jack and the
VAG1359/2 universal mount. - Roll VAG1383A transmission jack with 3282 transmission support
under transmission and support transmission.
- Support transmission using VAG1383A transmission jack.

- Align adjustment plate parallel to transmission and lock safety support
(arrow) on transmission.
Pa
ge 9 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-30

Transmission, transporting


Special tools and equipment

3282 transmission support
3336 transmission support jig
The transmission support jig can be used when
transporting the transmission and for setting up
3282 transmission support.

- Bolt 3336 transmission support jig to transmission housing.

- Adjust support jig on sliding piece using locking pin (arrow).
Number of visible holes = 17
- Lift transmission using workshop crane and 3336 transmission support
jig.
Pa
ge 13 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-31

Installing

Installation is the reverse order of removal, note
the following:

- Clean input shaft splines and (in case of used
clutch plates) hub splines. Remove corrosion
and apply only a very thin coating of lubricant G
000 100 on splines. Do not grease guide sleeve.

- Check throwout bearing for wear and replace if
necessary.

- Before installing, coat contact surface of clutch
release lever plunger with thin layer of copper
grease, e.g. Z 381 351 TE.

- Threaded holes for mounting clutch slave
cylinder to transmission and shift lever to shift
rod must be cleaned of locking compound
residue using threaded tap before installation.

- Make sure centering sleeves for engine to
transmission are installed correctly in cylinder
block. Install or replace if necessary.

- Always replace self-locking nuts.

-
Install engine/transmission intermediate plate (if
Pa
ge 14 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

34-32


Repair Manual, Electrical Equipment, Repair Group 27

Repair Manual, Engine Mechanical, Repair Group 26
Radio Operating Manual - Lift transmission until clutch slave cylinder with mounting bracket for
line/hose can be installed (arrow).
- Install lower engine/transmission and starter mounting bolts and install
starter.
- Check adjustment of shift mechanism and adjust if necessary Page
34
-12
.
- Align exhaust system free of stress.- Check transmission oil level Page 34
-36
.
- After connecting battery, enter anti-theft code for radio.- Fully close power windows to stop.
- Then activate all power window switches ("up") for at least a second to
activate automatic window raising/lowering.
- Set clock to correct time.
Pa
ge 16 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2

manifold
Clamp for exhaust pipe 40 Nm (30 ft
lb)
Bracket for noise insulation panel
to body 10 Nm (7 ft
lb)


1) Always replace bolt.
2) Coat with locking fluid D 185 400 A2 before
installing.
Pa
ge 20 of 20 Transmission, removin
g and installin
g
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.TM01.34.2