AUDI A4 1998 B5 / 1.G AEB ATW Engines Valvetrain Servicing Workshop Manual
A4 1998 B5 / 1.G
AUDI
AUDI
https://www.carmanualsonline.info/img/6/960/w960_960-0.png
AUDI A4 1998 B5 / 1.G AEB ATW Engines Valvetrain Servicing Workshop Manual
Page 17 of 51
15-44
Installing - Grease threaded head of 2085 seal puller, attach and with forced
pressure screw into oil seal as far as possible.
- Loosen knurled bolt and turn inner part against crankshaft until oil seal
is removed.
- Clamp 2085 seal puller in vise at flat surfaces. Remove oil seal using
pliers.
- Lightly oil lip of oil seal.
- Place 3241/2 guide sleeve on end of camshaft.
- Slide oil seal over guide sleeve.
Pa
ge 17 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
Page 18 of 51
15-45
- Using 3241/5 camshaft fitting tool and 3241/1 pressure sleeve, press
oil seal in to stop.
- Install camshaft gear.
Note position: thin rib of camshaft gear points outward (arrows) and
TDC Cyl. 1 marking is visible from the front.
- Using 3036 retainer, install camshaft gear retaining bolt.
Pa
ge 18 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
Page 21 of 51
15-48
Installing - Grease threaded head of 2085 seal puller, attach and with forced
pressure screw into oil seal as far as possible.
- Loosen knurled bolt and turn inner part against crankshaft until oil seal
is removed.
- Lightly oil lip of oil seal.
- Place 3241/2 guide sleeve on end of camshaft.
- Slide oil seal over guide sleeve.
Pa
ge 21 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
Page 22 of 51
15-49
Note:
When installing ribbed belt, make sure it is seated correctly on the pulleys.
Tightening torques - Using 3241/3 camshaft fitting tool and 3241/1 pressure sleeve, press
oil seal in to stop.
- Install Camshaft Position (CMP) sensor -G40- Page 15
-38
.
- Install upper toothed belt cover.
- Install ribbed belt and ribbed belt tensioner Page 13
-15
.
Component
Tightening
torques
Shutter wheel for Camshaft Position (CMP) sensor -
G40- to camshaft 25 Nm (18 ft lb)
Housing for Camshaft Position (CMP) sensor -G40-
to cylinder head 10 Nm (7 ft lb)
Pa
ge 22 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
Page 37 of 51
15-62
Valve stem oil seals, replacing
Cylinder head installed
Special tools and equipment
VW653/3 pressure hose
3122B spark plug removal tool
3362 valve spring tool and 3362/1 pressure
piece
3364 valve seat tool
3365 valve stem seat fitting tool
Removing
- Remove camshafts and hydraulic chain
tensioner Page 15
-50
.
- Remove valve lifters and lay aside with camshaft
contact surface facing down. Be careful not to
interchange valve lifters.
-
Using 3122B spark plug removal tool, remove all
Pa
ge 37 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
Page 45 of 51
15-69
Installing
- Using 3360 driver, press new, oiled valve guides
from camshaft side to collar into cold cylinder
head.
Note:
After valve guide with collar is seated, insertion
pressure may not exceed 10kN (2248 lbs =
approx 1.0t), as collar may break off.
- Using 3363 reamer -7 mm, ream valve guide.
Use cutting fluid.
- Reface valve seats Page 15
-71
.
- Replace valve stem oil seals Page 15
-62
.
Pa
ge 45 of 51 Valvetrain, servicin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.3
