check engine AUDI A4 1998 B5 / 1.G AFC Engine On Board Diagnostic Multiport Fuel Injection Repair Manual

01-88

Output on GST and/or on
VAG 1551 scan tool Possible malfunction cause

Malfunction repair
P0706 / 17090
Transmission Range Sensor
Circuit Range/Performance Engine control module incorrectly coded

- Cause: the vehicle is equipped with
manual transmission, but was coded
for vehicle with automatic
transmission.
- Remedy: code vehicle correctly
according to Coding Table

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not displayed by
MIL Automatic transmission: faulty wiring
connection between Engine Control Module
(ECM) -J192- and multi-function Transmission
Range (TR) switch -F125-

- Check gear recognition signal
page 24
-99

For troubleshooting
Display group 004
Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again

Automatic transmission: malfunction of
multi-function Transmission Range (TR) switch
-F125-

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01
- Check multi-function Transmission
Range (TR) switch -F125-

Malfunction cause found: Yes

Pa
ge 118 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-89

Output on GST and/or
on VAG 1551 scan
tool Possible malfunction cause

Malfunction repair
P0707 / 17091
Transmission Range
Sensor Circuit Low
Input Wiring connection between Engine Control
Module (ECM) -J192- and multi-function
Transmission Range (TR) switch -F125- on
automatic transmission faulty

- Check gear recognition signal page 24
-99


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and
after test drive, check DTC memory
again
MIL Status:
Malfunction not
displayed by MIL Malfunction on multi-function Transmission
Range (TR) switch -F125- of automatic
transmission

Repair Manual, 5 Spd. Automatic
Transmission 01V On Board Diagnostic (OBD), Repair Group 01, Electrical testing

- Check multi-function Transmission
Range (TR) switch -F125-
For troubleshooting
Display group 004
Malfunction cause found: Yes


- Erase DTC memory, test drive and
after test drive, check DTC memory
again
Pa
ge 120 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-91


Engine Control Module
(ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC
memory and test drive check DTC memory
Note:
The malfunction "P1101 / 17509" is set 123 sec after engine start and at a coolant temperature over 30 C (86 F) as soon as
the oxygen sensor control has reached the rich limit for 2 sec more than 20 times (or 40 sec. without interruption).
Pa
ge 122 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-92

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1102 / 17510
Heating Circ. (B1-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z19- (B1-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection of Oxygen Sensor
(O2S) heater -Z19- (B1-S1) faulty, or heater
-Z19- faulty

- Check O2S heater -Z19- (B1-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

|The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 123 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-94


Wiring connection to Oxygen Sensor (O2S) behind Three
Way Catalytic Converter (TWC) -G130- (B1-S2) faulty, or
sensor -G130- faulty

- Check O2S behind three way catalytic converter -
G130- (B1-S2) page 24
-53


Malfunction cause found: Yes
No
Continued next page

- Erase DTC memory, test drive and after test drive,
check DTC memory again

Engine Control Module (ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC memory and test drive
check DTC memory
Note:
The malfunction "P1104 / 17512" is set 123 sec after engine start, coolant temperature over 80 C (176 F), oxygen sensor
control active, engine speed between 1500 min and 5000 min, load between 19% and 80% and probe heater switched on at
least 45 sec, as soon as the signal voltage is less than 0.040 V for longer than 60 sec.
Pa
ge 126 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-95

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1105 / 17513
Heating Circ. (B1-S2)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z29- (B1-S2) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection of Oxygen Sensor
(O2S) heater -Z29- (B1-S2) faulty, or heater
-Z29- faulty

- Check O2S heater -Z29-(B1-S2) page 24
-55


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Pa
ge 127 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-98


Engine Control Module
(ECM) -J192- faulty

- Replace and code engine control module page 01
-265
erase DTC
memory and test drive check DTC memory
Note:
The malfunction "P1106 / 17514" is set 123 sec after engine start, with a coolant temperature over 30 C (86 F) as soon as
the oxygen sensor control has reached the rich limit for 2 sec more than 20 times (or 40 sec. without interruption).
Pa
ge 130 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-99

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1107 / 17515
Heating Circ. (B2-S1)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z28- (B2-S1) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately Wiring connection of Oxygen Sensor
(O2S) heater -Z28- (B2-S1) faulty, or heater
-Z28- faulty

- Check O2S heater -Z28- (B2-S1) page 24
-51


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating of the oxygen sensor probes in front of Three Way Catalytic Converter (TWC) is switched on with the fuel
pump relay, i.e. immediately at engine start.
Pa
ge 131 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-101

Output on GST and/or
on VAG 1551 scan tool Possible malfunction
cause
Malfunction repair

Engine Control Module
(ECM) -J192- faulty

- Replace and code engine control module page 01
-265

erase DTC memory and test drive check DTC
memory
Note:
The malfunction "P1109 / 17517" is set 123 sec after engine start with coolant temperature over 80 C (176 F), oxygen
sensor control active, engine speed between 1500 RPM and 5000 RPM, load between 19% and 80% and probe heater
switched on at least 45 sec., as soon as the signal voltage is less than 0.040 V for longer than 60 sec.
Pa
ge 135 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-102

Output on GST and/or
on VAG 1551 scan tool
Possible malfunction cause

Malfunction repair
P1110 / 17518
Heating Circ. (B2-S2)
Short to B+ Harness connector for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) loose or
corroded due to moisture in the harness
connector

- Check harness connector for tight fit and
contact corrosion, if necessary reconnect
and/or clean, installation location page 24
-1

Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
MIL Status:
MIL lights up
immediately
Wiring connection for Oxygen Sensor
(O2S) heater -Z30- (B2-S2) faulty, or heater
-Z30- faulty

- Check O2S heater -Z30- (B2-S2) page 24
-55


Malfunction cause found: Yes
No

- Erase DTC memory, test drive and after
test drive, check DTC memory again
For troubleshooting
Display group 040
Engine Control Module (ECM) -J192-
faulty

- Replace and code engine control module
page 01
-265
erase DTC memory and
test drive check DTC memory
Notes:

The heating for Oxygen Sensor Probes behind Three Way Catalytic Converter (TWC) is not switched on immediately at
engine start, but when the calculated exhaust gas temperature drops below 308 C (586 F) ( Read measuring value
Pa
ge 136 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1