wheel bolts AUDI A4 1998 B5 / 1.G AWM Engine Sealing Flanfes And Flywheel Drive Plate Workshop Manual

13-58


- Remove toothed belt sprocket from crankshaft. To do this, counter hold
sprocket with 3415.
- Remove oil pan Page 17
-11

- Remove bolts -1 to 6-.
- Pry sealing flange loose and remove.
- Carefully remove any remains of sealant from cylinder block.
Pa
ge 12 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2

13-60


Note:
The bead of sealant must not be thicker than 3 mm, otherwise excess
sealant will enter the oil pan and obstruct the strainer in the oil intake line.
Note:
Use guide sleeve T10053/1 to attach the sealing flange with sealing ring
installed.
Note:
After assembly, the sealant must dry for approx. 30 min. Only then may
the engine be filled with oil. - Apply bead of silicone sealant -arrow-onto clean sealing surface of
sealing flange, as illustrated (arrow).
Sealant bead width -arrows-: 2 to 3 mm
- Install sealing flange immediately, and tighten all bolts lightly.
- Tighten sealing flange bolts in diagonal sequence.
- Install oil pan Page 17
-23
.
Pa
ge 14 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2

13-62

Dual mass flywheel/drive plate,
removing and installing


Dual-mass flywheel

Special tools and equipment

Removing
Counter-hold tool 10-201

- Reverse position of counter-hold tool 10-201 for loosening/tightening
bolts.
- Mark position of flywheel relative to engine.
- Unbolt flywheel.
Pa
ge 16 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2

13-63

Installing
Installation is carried out in the reverse order or
removal; note the following:

- Replace bolts.

Tightening torque

Component

Nm
Dual-mass
flywheel 22.5 mm
1) 60 + 90
2)

on crankshaft
43 mm
1)
60 + 180

3)


1) Bolt length
2) 90 corresponds to a quarter turn

3)180 =
1/2 turn
Pa
ge 17 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2

13-65

Installing

- Place drive plate in position with shim -2- and washer -1-. Lug -arrow-
must face towards torque converter.
- Insert at least 3 old securing bolts and tighten to 30 Nm.

- Measure distance -a- at three points and calculate average value.
Specified value: 18.9 to 20.5 mm
Pa
ge 19 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2

13-66
If nominal value is exceeded:

If specified value is attained:
Tightening torque 1) 90 corresponds to a quarter turn - Remove drive plate again and fit without shim -2-. Retighten bolts to 30
Nm.
- Measure distance again.
- Install new bolts and tighten.Component

Nm
Drive plate to crankshaft
60 + 90
1)

Pa
ge 20 of 20 Sealin
g flan
ges and fl
ywheel/drive
plate, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE06.13.2