steering AUDI A4 1999 B5 / 1.G 01V Transmission Select Lever Mechanism Workshop Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 1999, Model line: A4, Model: AUDI A4 1999 B5 / 1.GPages: 75, PDF Size: 0.76 MB
Page 33 of 75

37-30
 
  
Tiptronic Switch -F189-, removing and 
installing
 
Installation location:  
The Tiptronic switch is integrated into the upper 
cover -1- of shift mechanism.  
 Repair Manual, 5 Spd. Automatic Transmission 
01V On Board Diagnostic (OBD), Repair Group 01; Performing On Board Diagnostic (OBD)
    -  For occurring malfunctions, the Tiptronic switch 
must be checked for interference in Measuring 
Value Block and in the electrical test. Tiptronic 
switch must only be replaced after wiring test. 
For vehicles with Tiptronic sport steering wheel, 
the buttons at steering wheel and their wire 
connections must be checked. Pa
ge 33 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1 
Page 53 of 75

37-48
 
  
 Repair Manual, Body Interior, Repair Group 69; 
Airbag; Steering wheel, removing and installing
    - Remove steering wheel.
-  Switch ignition key to driving position (ignition 
on). 
-  Shift selector lever into position "P".
-  Lift up retaining clip of interlock lever -1- and pull 
locking cable out of ignition/starter switch. 
-  Remove cover with guide (selector lever 
mechanism)  page 37
-5 . 
-  Unclip locking cable from securing spring at shift 
mechanism housing, slightly lift up securing 
spring to do so   Fig. 1
 ,   page 37
-21
 . 
-  Loosen and remove locking cable from cable tie 
-2-. 
Pa
ge 53 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1 
Page 55 of 75

37-50
 
  
Adjusting  
-  Shift selector lever into position "P".
- Loosen bolt -6-.
-  It must be possible to slide bracket -3- in 
direction of arrow -5-. 
-  Adjust steering column downward.
-  Connect 3352 A adjustment pin for shift lock 3 -
item 4- between lever (for locking cable) and 
locking coupling ring. 
-  Pull locking cable in direction of arrow -5- and 
tighten bolt -6- to 10 Nm. 
-  Remove adjusting gauge.
-  Check ignition key removal lock after every 
adjustment of the locking cable   page 37
-1 . 
Pa
ge 55 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1 
Page 56 of 75

37-51
 
  
 Repair Manual, Body Interior, Repair Group 69; 
Airbag; Steering wheel, removing and installing
   
 Repair Manual, Body Interior, Repair Group 68; 
storage compartments/covers; front center console, removing and installing
    -  Install steering wheel.
-  Front center console, installing-  Selector lever handle, installing   page 37
-22
-  Connect battery Ground (GND) strap.
-  For vehicles equipped with coded anti-theft 
radio, activate code. 
Pa
ge 56 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1 
Page 72 of 75

37-67
 
  
Locking cable for shift mechanism 
(without Tiptronic), removing and 
installing
 
Note: 
Removing:  
 Repair Manual, Body Interior, Repair Group 68; 
storage compartments/paneling; removing storage bin on driver's side
   
 Repair Manual, Electrical Equipment, Repair 
Group 92; Steering column switches, servicing; Steering column switches, removing and installing
     
Locking cable must not be kinked.
-  Disconnect Ground (GND) strap from battery.
-  Remove driver-side storage compartment below 
steering wheel. 
-  Remove steering column switch.
Pa
ge 72 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1 
Page 74 of 75

37-69
 
  
Installing and Adjusting  
-  Installation is the reverse of removal.
-  Install locking cable without kinking and secure 
at indicated position using cable tie -2-. 
-  Adjust steering column rearward/downward.
-  Check locking mechanism of interior lever -1-.
-  Slightly loosen bolt -6-.
-  It must be possible to slide bracket -3- in 
direction of arrow -5-. 
-  Make sure securing spring is correctly seated in 
shift mechanism housing. 
-  Hook locking cable bracket -3- into shift 
mechanism and locking coupling ring in lever (for 
locking cable). 
Pa
ge 74 of 75 Selector lever mechanism, servicin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.37.1