display AUDI A4 1999 B5 / 1.G APB Engine Charge Air System With Turbocharger Workshop Manual

21-11


Notes: - Switch on turbocharger tester and set measuring range selector switch
to position -I- (absolute pressure).
- Connect measuring hose to connection -I-.
Hose connections must be completely airtight, otherwise
measurements will not be correct. Ensure that measuring hose is not pinched at hood or side window.Pressing memory key M on turbocharger tester will store the last
measured value until memory key M is pressed again or tester is
switched off. The decimal point in the display flashes to indicate that the value is
being stored. If the battery voltage of the turbocharger tester drops below the
minimum level, an arrow will appear at the top left of the display. Before performing the test, drive the vehicle at a brisk speed for at
least 3 km (without stopping at traffic lights etc.). A second mechanic is required to note the readings on the tester
when the vehicle is moving. Observe safety notes Page 21
-9 .
Pa
ge 12 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-14

Test sequence

Repair Manual, 2.7 Liter V6 5V BiTurbo Fuel Injection & Ignition,
Engine Code(s): APB, Repair Group 01
- Connect VAS 5051 tester or VAG 1551 scan tool and select control
module for engine electronics using "address word" 01. Engine must
run at idle.
Rapid data transfer
HELP
Select function XX

When indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block" and
press -Q- button to confirm input.
Read measurin
g value block
Q
Input displa
y group number XXX

When indicated on display
- Press buttons -1-, -1- and -5- to select "display group number 115" and
press -Q- button to confirm input.
Read Measuring Value Block 115

Indicated on display (1...4 display fields)
Pa
ge 15 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-15

- Road test vehicle.


Wide Open Throttle (WOT) must be
reached

- Measurement must be taken at Wide Open
Throttle (WOT).

Display fields

1 2 3 4
Display group 115: Charge air pressure regulation
Display 1 RPM % mbar mbar
Indicated Engine speed (RPM) Actual load Specified pressure Actual pressure
Specified value XXX Must not deviate more
than +/- 20 mbar
from specified
Note: Actual pressure must not deviate from specified
pressure by more than 20 mbar.
Pa
ge 17 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-16

- Select measuring value block 117.

- Check function of accelerator pedal in display
field 2 by briefly depressing pedal to Wide Open
Throttle.

Display fields

1 2 3 4
Display group 117: Charge air pressure regulation
Display 1 RPM
% % mbar
Indicated Engine speed (RPM)
Accelerator pedal
position Throttle valve angle Specified charge air
pressure
Specified value
0...100
Note: If the specified value 100% is not reached at
Wide Open Throttle (WOT):

- Check accelerator pedal.

- Select measuring value block 116.
Pa
ge 18 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-17

- Check correction factors in display fields 2 to
4.

Display fields

1 2 3 4
Display group 116: Charge air pressure regulation
Display 1 RPM
% % mbar
Indicated Engine speed (RPM)
Correction factor
Fuel Correction factor
Coolant temp. Correction factor
Intake air temp.
Specified value


Note: If display field 2 indicates a correction factor <0
%, fuel quality is probably incorrect.

- Fill tank with prescribed fuel quality.
If display field 3 indicates a correction factor <0
%, coolant temperature is too high (heat warning
lamp lit in instrument cluster) or the Engine
Control Module is receiving an incorrect
temperature signal from the instrument cluster.

- Check coolant temperature display.

Pa
ge 19 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-18
If display field 4 indicates a correction factor <0
%, intake air is too hot or the sensor for intake air
temperature is faulty.

Repair Manual, 2.7 Liter V6 5V BiTurbo Fuel
Injection & Ignition, Engine Code(s): APB, Repair Group 24


- Select measuring value block 114.

Display fields

1 2 3 4
Display group 114: Charge air pressure regulation
Display
%
%
% %
Indicated
Specified engine load (without
correction) Specified engine load (after
correction) Actual
load Duty cycle
CAPR-cyclical
valve
Specified
value 136,0
134,3
137,5 55,2
Note: Load values in display fields 1 to 3 can deviate
from each other by up to 5 %. If specified values are not achieved in the
Pa
ge 21 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-20

Note:
The recirculating valve for turbocharger -N249
and wire connections are monitored by the
Engine Control Module (ECM).

- Connect VAS 5051 tester or VAG 1551 scan
tool and select control module for engine
electronics using "address word" 01. Engine
must run at idle for this.

Repair Manual, 2.7 Liter V6 5V BiTurbo Fuel
Injection & Ignition, Engine Code(s): APB, Repair Group 01


- Check DTC memory of Engine Control Module
(ECM).

Repair Manual, 2.7 Liter V6 5V BiTurbo Fuel
Injection & Ignition, Engine Code(s): APB, Repair Group 01

If a Diagnostic Trouble Code (DTC) relating to
the recirculating valve for turbocharger -N249- is
displayed:

-
Disconnect hoses from valve; harness connector
Pa
ge 24 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1

21-21

- Initiate output Diagnostic Test Mode (DTM) and
activate recirculating valve for turbocharger -
N249-.

Repair Manual, 2.7 Liter V6 5V BiTurbo Fuel
Injection & Ignition, Engine Code(s): APB, Repair Group 01

Output diagnostic test mode Recr. valve for turbocharger -N249

Indicated on display
If valve does not click:
If valve does not open and close properly: Valve must click...
...and must open and close (can be tested by blowing into assisting
hose).
- Check internal resistance of valve.
- Replace recirculating valve for turbocharger -N249-.
Pa
ge 26 of 37 Char
ge air s
ystem with turbochar
ger
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.21.1