engine oil AUDI A4 1999 B5 / 1.G APB Engine Lubrication System Components User Guide

17-34


- Also open coolant drain screw -arrow- at rear right of oil pan.
- Draining off and filling up coolant Page 19
-19
.
- Drain off engine oil.
Use a separate container to collect the engine oil.

- Set up support bracket 10-222A with adapter 10-222A/3 on bolted
flanges for wing panels.
- Attach support bracket to front and rear lifting eyes on engine.
- Raise engine as far as possible with spindles of support bracket.
Pa
ge 36 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-36

- Place drip tray VAG 1306 under engine.

- Remove oil filter.

- Release hose clamps -arrows-.
- Remove oil cooler -1-.

- Remove bottom nuts on engine mountings -1- (left and right sides).
- Mark positions of securing points -1- and locating sleeves -2- under
engine mountings on left and right sides.
Pa
ge 38 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-41


- Unbolt two oil supply lines, and pull longer of two lines downward to
disconnect from upper section of oil pan.

Note:
Two M6 bolts and two M8 bolts are located vertically at rear of oil pan
upper section (in front of joint between engine and transmission). - Unbolt oil pump from engine so that shorter oil supply line can be
disconnected (do not remove oil pump).
- Remove bolts securing upper section of oil pan to transmission.
- Unbolt upper section of oil pan from engine.
Pa
ge 43 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-42

Installing:
Install in the opposite order to removing. When
installing, note the following points:

- Clean sealing surfaces; ensure that they are free
of oil and grease.

WARNING!

Wear protective goggles.

Note:
The oil pan must be installed within 5 minutes after applying silicone
sealant D 454 300 A2. - Remove any residues of sealant on oil pan and engine block using
plastic brush attachment, or similar.

- Cut off nozzle of tube at front marking (diameter of nozzle approx. 3
mm).

Thickness of sealant bead: 2 ... 3 mm
Pa
ge 44 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-44

- Clean both sealing surfaces for lower section of
oil pan; ensure that they are free of oil and
grease.

Note:
Do not use any adhesive or sealant.

- Install new gasket on lower section of oil pan
and install on upper section of oil pan with two
diagonally opposite bolts.

- Tighten all securing bolts hand-tight.

- Tighten bolts to 10 Nm with torque wrench,
working from center outward.

- Install new seal on oil drain plug and tighten to
30 Nm.

Notes:

When installing the upper section of the oil pan
with the engine removed from the vehicle,
ensure that the oil pan is positioned flush with
the cylinder block at the flywheel end.
The sealant must be left to dry for about 30
minutes after installing the oil pan before engine
Pa
ge 46 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-45

- Fill with coolant Page 19
-19
.

- Fill engine with oil.

Repair Manual, Maintenance


- Install subframe.

Repair Manual, Suspension, Wheels,
Steering, Repair Group 40


- Install lock carrier in normal position.

Repair Manual, Body Exterior, Repair Group
50


- Install bumper.

Repair Manual, Body Exterior, Repair Group
63


Pa
ge 48 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-46

Tightening torques

Component

Nm
Upper section of oil pan to cylinder
block M6 10
M8 20
Lower section of oil pan to upper
section of oil pan 10
oil pan to transmission M8 25
M10 45
Coolant line to oil pan 10
Oil drain plug in lower section of oil
pan 30
Dipstick guide tube to cylinder head 25
Oil pump to cylinder block 25
Oil pump supply lines to upper
section of oil pan 10
Front sealing flange M6 10
Collar bolt M8 30
Bracket for coolant lines to oil pan 10
Coolant drain screw on engine 20
Pa
ge 50 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-47

Component

Nm
Stop for torque reaction support to
bracket on engine
25
Engine mounting to subframe 25
Torque reaction support to front of oil pan 25
Engine mounting to engine support 25
Chain sprocket to oil pump 25

Other tightening torques
** Combi bolt -4- must be replaced after removing. Nut for engine mounting -1- 25
Bolts -2- and -3- 60
Combi bolt -4- **
110 + 90
Pa
ge 51 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-49

WARNING!

Do not open air conditioner refrigerant
circuit.

Notes:
Note:
Use a separate container to collect the engine oil. - Detach air conditioner compressor -1...3-.
Watch position of guide bushes when installing.When installing, insert bolt -1- in the compressor first. To prevent damage to the condenser and refrigerant lines/hoses,
ensure that the lines and hoses are not stretched, kinked or bent.
- Drain engine oil.
Pa
ge 53 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1

17-53

- Clean both sealing surfaces for lower section of
oil pan; ensure that they are free of oil and
grease.

Note:
Do not use any adhesive or sealant.

- Install new gasket on lower section of oil pan
and install on upper section of oil pan with two
diagonally opposite bolts.

- Tighten all securing bolts hand-tight.

- Tighten bolts to 10 Nm with torque wrench,
working from the center outwards.

- Install new seal on oil drain plug and tighten to
30 Nm.

- Fill up engine oil.

Repair Manual, Maintenance


- Install subframe.

Pa
ge 57 of 74 Lubrication s
ystem com
ponents, removin
g and installin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE05.17.1