air condition AUDI A4 1999 B5 / 1.G AWM Engine Readiness Code Workshop Manual

01-78

Readiness code is returned to "0 1 1 0 1 1 0
1" if:

DTC memory was erased,
Voltage supply to ECM was cut off (e.g.
connector disconnected, battery disconnected)
a new Engine Control Module (ECM) was
installed
In this case, readiness code must be re-
generated Page 01
-84
.

Note:
During driving operation in various load
conditions, exhaust relevant tests are performed
by the control module and the readiness code is
generated on its own. In this case, however, the
concluding control possibilities are not available,
meaning that it will not be indicated whether the
vehicle is free of malfunctions upon transfer to
the customer.
Pa
ge 2 of 43 Readiness code
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-90


Display fields

1 2 3 4
Display group 060: Adaptation of throttle valve control module
Display xx % xx %
x
---
Indicated Throttle
valve angle
(angle
sensor 1) Throttle
valve angle
(angle
sensor 2) Adaptation step counter
Adaptation condition
Functional
range
0 to 8
ADP in progress
ADP OK
ERROR
Specified
value 3 to 93 % 97 to 3 %
8
ADP OK
Note


After adaptation, the adaptation step
counter reaches the number 8 (it is OK for
numbers to be skipped). If "ERROR." is displayed:
Check DTC memory Page
01
-12
.
If specified value is not
obtained: Note, Page 24
-
130

Note for display field 3:
Different numbers are shown in display field 3 during adaptation that represent the current adaptation condition. It is not
particularly important how the adaptation step counter (display field 3) behaves during adaptation, but rather that display field
Pa
ge 16 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-92


Display fields

1 2 3 4
Display group 063: Kick down function, adapting
Display xx % xx %
Kick
down ---
Indicated Sensor 1
for
Pedal
position learned kick down value for Throttle
Position (TP) sensor Kick
down Adaptation condition
Functional
range
Kick
down operate
ADP in progress
ADP OK
ERROR
Specified
value 79 to 94 % 79 to 94 %
Kick
down ADP OK
Note



If "ERROR." is displayed: Check DTC
memory Page 01
-12
.
Note for display field 4:
"ERROR" can be indicated, for example, if the accelerator pedal is not immediately pressed in response to a request by the
tester or if the accelerator pedal is released while adaptation is running despite the fact that adaptation is not yet complete. In
both cases, "Basic Setting" must be exited and the adaptation must be performed again.
Pa
ge 19 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-93

Work step 5: Check operating condition of
oxygen sensor control

- Start engine (for a vehicle with manual
transmission: engage clutch).

Note:
If necessary, vehicle system "01 - engine
electronics" and diagnostic function "04 -basic
setting" must be selected again after engine
start.

- Install VAG1788/10 RPM adjuster on the
accelerator pedal and raise the engine speed to
2600 RPM.

Test requirement:

Engine running at 2600 RPM.

Display on VAS5051:
-
Click on - button
Pa
ge 21 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-95


Display fields

1 2 3 4
Display group 030: Oxygen sensor status
Display
X X X
X X X


Indicated
Oxygen sensor status, bank 1, sensor 1
Oxygen sensor status, bank 2, sensor 1


Functional range
0 = off
1 = on 0 = off
1 = on

Specified value
1 1 1
1 1 0

Significance of 3 digit indications in display group 030 X
X
X
Display fields 1 and 2
X Oxygen sensor control: 0= not active; 1 = active
X Operational readiness of oxygen sensor: 0= not active; 1 = active
X Condition of oxygen sensor heater: 0= not active; 1 = active
Notes:

The first position of the 3 digit indication (heating) fluctuates between 0 and 1 at certain operation points.
Oxygen sensor control of oxygen sensor behind catalytic converter (bank 1, sensor 2) is not active without engine load,
meaning that the third position of the 3-digit display is 0.

-
Do not start test until indication in display field 1
Pa
ge 23 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-97


Display fields

1 2 3 4
Display group 034: Oxygen sensor aging diagnostic, oxygen sensor before catalytic converter (bank 1)
Display xxxx/min
xxx C
x.x
---
Indicated Engine speed
(RPM) Exhaust
temperature Dynamic
factor Diagnostic condition
Functional
range Test OFF
Test ON
B1-S2 OK
B1-S2 not OK
Specified
value 2600 RPM larger than 350
C
0.5 to 2.5 B1-S2 OK
Note



If "B1-S1 not OK" is displayed: Check DTC
memory Page 01
-12
.
If specified value "B1-S1 OK" is obtained:

- Perform next work step.
Pa
ge 26 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-99


Display fields

1 2 3 4
Display group 036: Operational readiness of oxygen sensor behind catalytic converter (bank 1)
Display x.xxx V
---

Indicated Oxygen sensor voltage Bank 2,
sensor 1 Diagnostic condition

Functional
range
Test OFF
Test ON
B1-S2 OK
B1-S2 not OK

Specified value 0.100 to 0.950 volts
B1-S2 OK

Note

If "B1-S2 not OK" is displayed: Check DTC memory
Page 01
-12



If specified value B1-S2 OK" is obtained:

- Perform next work step.
Pa
ge 28 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-101


Display fields

1 2 3 4
Display group 037: Diagnostic of oxygen sensor control system (Bank 1)
Display xxx % x.xxx V x.xx
---
Indicated Load Oxygen sensor
voltage Bank 2,
sensor 1 Oxygen sensor correction value
between bank 1, sensor 1 and bank 1,
sensor 2 Diagnostic condition
Functional
range
Test OFF
Test ON
System OK
System not OK
Specified
value 13 to
40 % 0.100 to 0.950 volts smaller than 0.02 System OK
Note



If "System not OK" is displayed:
Check DTC memory Page 01
-
12

If specified value "Syst. OK" is obtained:

- Perform next work step.
Pa
ge 30 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-104


Display fields

1 2 3 4
Display group 043: Oxygen sensor aging diagnostic, oxygen sensor behind catalytic converter (bank 1)
Display xxxx/min
xxx C
x.xxx V
---
Indicated Engine speed
(RPM) Exhaust
temperature Oxygen sensor voltage
Bank 2, sensor 1 Diagnostic condition
Functional
range Test OFF
Test ON
B1-S2 OK
B1-S2 not OK
Specified
value 2600 RPM larger than 350
C
0.100 to 0.950 volts B1-S2 OK
Note



If "B1-S2 not OK" is displayed: Check
DTC memory Page 01
-12

If specified value B1-S2 OK" is obtained:

- Perform next work step.
Pa
ge 33 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7

01-106


Display fields

1 2 3 4
Display group 046: Diagnostic of catalytic converter (bank 1)
Display xxxx/min
xxx C
x.xx
---
Indicated Engine
speed
(RPM) Exhaust temperature Measurement
Catalytic
converter -
conversion Diagnostic condition
Functional
range 0 to 8 Test OFF
Test ON
Cat B1 OK
Cat B1 not OK
Specified
value 2600 RPM
550 to 700 C
Larger than 1.0 Cat B1 OK
Note

As long as the exhaust temperature
is not within the specified range, the
test will not be initiated. If necessary,
increase or decrease RPM
If "Cat B1 not OK" is displayed:
Check DTC memory Page 01
-
12
. If no DTCs are stored,
replace catalytic converter.
If specified value "Cat B1 OK" is obtained:

- Perform next work step.
Pa
ge 35 of 43 Readiness code11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU07.01.7