warning lights AUDI A4 1999 B5 / 1.G Brakes Output DTM 03 Workshop Manual

01-180

Function test: ABS/EDL warning light -K47-
Test step
VAG
1598
sockets Test of
Test
requirements
- Additional work
steps Specified value
Corrective action
8

Continuation: - Function of
ABS/EDL
warning light
-K47-. - Switch on
ignition ABS warning
light -K47- lights
up for two (2)
seconds and
then goes out.
Electrical Wiring Diagrams,
Troubleshooting & Component Locations - If ABS/EDL warning light does not come
on, check voltage of electrical system and
test wiring from terminal 21 of ABS control
module -J104- to instrument cluster for
short circuit to Ground (GND).
- The ABS/EDL warning lamp does not
switch off after 2 seconds. The red "brake
system malfunction" symbol lights up after
2 seconds. Check wire from terminal 21 of
ABS control module -J104- to instrument
cluster for short circuit to B+ and open
circuit.

Repair Manual, Electrical Equipment,
Repair Group 90.
- If vehicle voltage and wire from terminal
21 of ABS control module -J104- to
instrument cluster are OK there is a
malfunction in instrument cluster, LED or
bulb malfunctioning.
Pa
ge 35 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-182

Function test: Red brake warning symbol
Test step
VAG
1598/20
sockets Test of
Test requirements
- Additional work stepsSpecified value
Corrective action
9

Continuation: Function of red
"brake system
malfunction"
symbol - Connect VAG1551 scan
tool and select address
word 03
- For vehicles with
automatic transmission and
high-line instrument cluster,
depress the brake pedal
and select a driving gear. The ABS indicator lamp
and the red "brake system
malfunction" symbol light
up. If the traction control
indicator light is installed
and OK, it also lights up. Repair Manual,
Electrical Equipment, Repair Group 90; instrument cluster.

- Malfunction in
instrument cluster
Pa
ge 37 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13

01-197

DTC
Possible cause
Corrective action
Printed output from VAG1551 Scan Tool
(ST)

00532
Voltage supply
Signal too small

Notes:

This malfunction affects the voltage supply
of the control module.
This DTC is only stored, if the malfunction
occurs at a vehicle speed above 6 km/h.
As soon as vehicle voltage is within the
valid voltage range again, the ABS/EDL or
ASR system is switched back on and the
warning lights turn off.
Open circuit or contact resistance
too high between voltage supply
from terminal 15 hydraulic control
unit, terminal 15. Voltage jumps in vehicle system.
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Electrical Wiring Diagrams,
Troubleshooting & Component
Locations
Repair Manual, Electrical
Equipment, Repair Group 27.
- Carry out "Electrical test", step
1 page 01
-166
.
- Locate and repair open circuit
in voltage supply. - Check Generator (GEN) and
Voltage Regulator (VR). - Check battery

Malfunction in hydraulic control unit- If no malfunctions can be
found in the voltage supply,
replace hydraulic control unit.
Pa
ge 57 of 66 Out
put Dia
gnostic Test Mode
(DTM
) (function 03
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.SU02.01.13