engine AUDI A4 1999 B5 / 1.G Engine Oil Level Checking User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 1999, Model line: A4, Model: AUDI A4 1999 B5 / 1.GPages: 111, PDF Size: 1.26 MB
Page 25 of 111

31
All models
- Start engine and check belt running.
- Check again to ensure that bolts for coolant
pump pulley are tightened to correct torque.
Pa
ge 25 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 29 of 111

Removing
- Move body, front, to engine service position
Page 24
.
- Remove ribbed V-belt cover.
Pa
ge 29 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 33 of 111

38
6-spd. manual transmission 01E all wheel
drive
Note:
For checking oil level the vehicle must be
stationary and on a level surface (e.g engine
off, standing on an alignment lift).
The oil level must be kept at the specified level.
The transmission may be damaged by over-
filling.
CAUTION!
If the oil level is too low, the transmission must be checked for leaks
and repaired. It is not sufficient to just top off oil.
CAUTION!
Part numbers are for reference only. Always check with your Parts
Dept. for the latest parts information. - Remove filler plug -B-, on differential cover, in front of drive axle flange.
- Check oil level using tool such as angled wire.
Specification: level 1 mm below bottom of oil filler hole.
- If there are no leaks, top up with gear oil: SAE 75 W 90 (synthetic oil),
part number G 052 145 S2 (1 liter).
Pa
ge 33 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 35 of 111

39
Automatic Transmission Fluid (ATF),
checking (01V transmission)
Requirements for check:
Vehicle standing on level surface.
Transmission must not be in fail-safe mode.
Shift lever in "P" position, parking brake
applied.
Engine idling.
Air Conditioner and heater OFF.
ATF temperature must not exceed 40 C
(104 F) at start of test.
CAUTION!
Part numbers are for reference only. Always
check with your Parts Dept. for the latest
parts information.
Notes:
Only ATF with designation ESSO LT 71 141
Pa
ge 35 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 37 of 111

40
CAUTION!
Too much or too liffle ATF will affect the
operation of the transmission. The ATF level
must be checked at regular intervals.
The oil level is correct if only a slight amount of oil runs out when ATF
temperature is between 30 C (86 F) and 45 C
1) (113 F) (caused by
increase of oil level when heated).
WARNING!
Wear protective glasses.
The ATF temperature is measured temperature using the VAG 1551 Scan
Tool. - Hang filled ATF reservoir VAG 1924 as high as possible (example:
radiator grill).
- Shift lever in "P", engine running at idle.
- Place oil drip pan under transmission oil pan.
- Connect VAG 1551 as described on Page 19
.
- Press key -1- for " Rapid Data Transfer " mode.
Pa
ge 37 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 42 of 111

44
Power steering fluid level, checking
Requirements:
Engine at normal operating temperature.
Vehicle stationary.
Front wheels in straight ahead position.
- Remove cap with dipstick from expansion tank
and wipe off dipstick with a lint-free cloth.
Delivery inspection:
Fluid level must be at max. marking when inspection is performed.
Inspection service:
Fluid level between min. and max. markings.
Note:
If oil level has dropped to the min. marking, check power steering system, - Reinstall cap with dipstick and remove again.
- Read max. and min. markings on dipstick. top off with G 002 000
hydraulic oil, if necessary, as follows:
Pa
ge 42 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 65 of 111

65
Battery no-load voltage, testing
Requirements:
Vehicle must have been standing for at least
two hours in the no-load state prior to
measurement (no engine starts, no charging
and discharging).
Ignition turned OFF
- Measure voltage with digital multimeter (Fluke
83, or equivalent) between poles of installed
battery.
If instrument indicates 12.5 volts or higher,
battery is OK.
If voltage is below 12.5 volts, determine cause
and repair or replace as necessary.
Pa
ge 65 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 81 of 111

80
Service Reminder Indicator (SRI),
resetting
Vehicles up to model year 1997
If service date has been reached, service event
which is due appears as a flashing display after
ignition is turned ON. Flashing continues for a
few seconds after engine is started.
The following displays are possible:
OIL Engine oil change
In 1 Inspection service
In 2 Inspection service with additional work
A service event which is due is already displayed
1000 km (620 mi.) or 10 days before.
Service Reminder Indicator (SRI) must be
matched during Delivery Inspection or during
each Inspection Service to the km and time
specifications until next service event with help of
Scan Tool (ST) VAG 1551.
- Select adaptation channels individually and
enter relevant specified values.
Pa
ge 81 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6
Page 90 of 111

89
Oil Change Service and Inspection Service
When a service is due, the type of service
required will be indicated by a flashing message
on the trip recorder display when the ignition is
switched on. The message will continue to flash
for up to 60 seconds after the engine has been
started.
Display
Type of service due
service OEL Oil Change Service
service INSP Inspection Service
When a service is due, this will be indicated
either 1,000 km or 10 days in advance.
Resetting service interval display with VAG
1551
- Connect VAG 1551 Page 83
.
- Switch ignition on.VAG On Board Diagnostic
HELP
1 - Rapid data transfer1
)
2 - Blink code output1
)
Indicated in display (
1) appears alternately)
- Enter "1" to select "Rapid data transfer".
Pa
ge 90 of 111 Descri
ption of wor
k
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.ME01.01.6