lock AUDI A4 2000 B5 / 1.G AEB Engine Additional Signal

24-146

Checking

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -5- and -0- to input display group number 50, and
press -Q- button to confirm input.
Read Measuring Value Block 50 1 2 3 4

Indicated on display (1-4 = display fields)
- Switch on A/C (lowest temperature and highest fan position).
Pa
ge 3 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5

24-150

Test procedure

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons -0-, -0- and -5- to input display group number 5, and
press -Q- button to confirm input.
Read Measuring Value Block 5 1 2 3 4

Indicated on display (1-4 = display fields)
Pa
ge 10 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5

24-152

Continuation
If no speed was indicated:

Notes:
If the LED does not blink:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
If the wiring is OK and the LED does not blink:
Repair Manual, Electrical Equipment, Repair Group 90
- Connect VAG 1598/22 test box to ECM harness connector Page 01
-
56
.
- Connect VAG 1527B LED voltage tester between ECM/test box
sockets 3 (B+) and 20 (signal).
- Lift vehicle at left front until wheel is free.
- Switch ignition on and rotate left-front wheel by hand.
LED must blink (very brief blink)
The right-front wheel must not rotate; block it if necessary.For LEDs with little voltage consumption, the LED lights up at half
strength when the ignition is switched on.
- Check wiring from ECM connector, terminal 20 to instrument cluster for
open circuit or short circuit
Pa
ge 13 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5

press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Pa
ge 16 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5

24-154

Read Measurin
g Value Block
HELP
Input display group number XXX

Indicated on display
- Press buttons -0-, -5- and -6- to input display group number 56, and
press -Q- button to confirm input.
Read Measuring Value Block 56 1 2 3 4

Indicated on display (1-4 = display fields)
- Compare display with specified value in display field 4:

Display fields

1 2 3
4
Display group 56: Engine idle
Display xxxx RPM xxxx RPM x.xx g/s
xxxx
Indicates Actual engine
speed
(in 10 RPM
steps) Specified engine
speed
(in 10 RPM
steps) Control value-Idle mass air flow
(idle air control valve) Operating condition
Range 0-2550 RPM --- ---
---
Specified
value 0 RPM 0 RPM -1.11 to 1.11 g/s
0000 = Selector lever in P or N
0010 = Selector lever in 2/3/4/R/D

--- --- ---
If not as specified Page 24
-155
,
Continuation;
Explanation of display Page 24-
16

Pa
ge 17 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5

24-158

Test procedure

- Connect VAG 1551 or VAG 1552 scan tool and
press buttons -0- and -1- to insert "Engine
Electronics" address word 01 (with engine
running at idle) Page 01
-7 .
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -8- to select "Read Measuring Value Block"
function 08, and press -Q- button to confirm input.
Read Measurin
g Value Block
HELP
Input displa
y group number XXX

Indicated on display
- Press buttons 1, 2 and 2- to input display group number 122, and press
-Q- button to confirm input.
Read Measuring Value Block 122 1 2 3 4

Indicated on display (1-4 = display fields)
WARNING!
A second technician is required to operate the VAG 1551 scan tool
during the road test. - Road test.
Pa
ge 22 of 29 Additional si
gnals
11/19/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU02.24.5