check engine AUDI A4 2000 B5 / 1.G APB Engine Motronic Syst
[x] Cancel search | Manufacturer: AUDI, Model Year: 2000, Model line: A4, Model: AUDI A4 2000 B5 / 1.GPages: 166, PDF Size: 0.53 MB
Page 22 of 166

01-19
 Diagnostic Trouble Code (DTC) table
 
Notes:  
 
If malfunctions occur in the sensors and components being monitored, they will be stored in the DTC memory together 
with an indication of the type of malfunction. Notes on Engine Power Control (EPC) (drive by wire)   Page 24
-139
 . 
 Malfunctions relating to the electronic throttle are also indicated by the EPC (Electronic Power Control) warning light in the 
instrument cluster. 
 Malfunction which decrease exhaust emissions are indicated by an Exhaust Malfunction Indicator Light (MIL), the MIL is 
located in the instrument cluster. As soon as certain malfunction are recognized, the MIL is switched on immediately. 
There are also malfunctions, were the MIL is switched on only after the engine is started again. 
 Sporadically occurring malfunctions (temporary malfunctions) will be indicated on the VAG1551 display as "SP."
 The DTC table is arranged according to the 5-digit DTC in the left-hand column.
 If a malfunction is stored in the DTC memory and then does not occur again during the next 40 engine warm-up phases, 
the DTC will be automatically erased. 
 Components that are indicated as being faulty by the VAG1551 should not be replaced immediately. Always start by 
checking the wiring, connectors and Ground (GND) connections for the component using the current wiring diagram. This 
is particularly important in the case of sporadic malfunctions (indicated by the letters "SP"on the scan tool display). 
 If the connector for the engine control module is disconnected or if the battery is disconnected, all the learned values 
(adaptation values) stored in the control module will be erased, although the contents of the DTC memory will remain 
intact. The next time the engine is started the idling may be rough at first. In this case let the engine run at idle for a few 
Pa
ge 22 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 24 of 166

01-20
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0101   16485   Mass Air Flow (MAF) sensor -
G70-  
Implausible signal  - Check Mass Air Flow (MAF) sensor   Page 24
-59
P0102   16486   Mass or Volume Air Flow 
Circuit  
Low input 
2)  - Check Mass Air Flow (MAF) sensor -G70   Page 24
-59
P0103   16487   Mass or Volume Air Flow 
Circuit  
High Input
 2)
    
P0106   16490   Manifold Abs.Pressure or 
Bar. Pressure  
Range/Performance 
2) 4)
   Repair Manual, 2.7 Liter V6 5V BiTurbo Engine Mechanical, Repair 
Group 21; Turbocharger; Checking Charge Air Pressure Sensor -G31   
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
4) Absolute manifold pressure will be determined by the Charge Air Pressure Sensor -G31 (instead of displayed -G71), the air 
pressure is determined by the Barometric Pressure (BARO) Sensor -F96 (in Engine Control Module (ECM))  
Pa
ge 24 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 25 of 166

01-21
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0112   16496   Intake Air Temp. Circ.  
Low Input
2)  - Check Intake Air Temperature (IAT) sensor   Page 28
-17
P0113   16497   Intake Air Temp.  
High Input
2)    
P0116   16500   Engine Coolant Temp. Circ.  
Range/Performance  - Check Engine Coolant Temperature (ECT) sensor   Page 28
-25
P0117   16501   Engine Coolant Temp. Circ.  
Low Input 
2)    
P0118   16502   Engine Coolant Temp. Circ.  
High Input 2)    
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 25 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 26 of 166

01-22
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0130   16514   02 Sensor Circ., Bank1-
Sensor1  
Malfunction 
2)  - Check oxygen sensor control or oxygen sensor heater and wiring   
Page 24
-79
 
P0131   16515   02 Sensor Circ., Bank1-
Sensor1  
Low Voltage 
2)    
P0132   16516   02 Sensor Circ., Bank1-
Sensor1  
High Voltage 2)    
P0133   16517   02 Sensor Circ., Bank1-
Sensor1  
Slow Response2)    
P0134   16518   02 Sensor Circ., Bank1-
Sensor1  
No Activity Detected
2)    
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 26 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 27 of 166

01-23
 
DTC  
Description of 
malfunction  
Corrective action  
SAE  
VAG  
  
  
P0136   16520   02 Sensor Circ., Bank1-
Sensor2  
Malfunction 
2)  - Check oxygen sensor heater   Page 24
-114
P0137   16521   02 Sensor Circ., Bank1-
Sensor2  
Low Voltage 
2)  - Check oxygen sensor signal wire and activation   Page 24
-122
P0138   16522   02 Sensor Circ., Bank1-
Sensor2  
High Voltage
2)    
P0139   16523   02 Sensor Circ., Bank1-
Sensor2  
Slow Response2)  - Check oxygen sensor and oxygen sensor control behind catalytic 
converter  Page 24
-100
 
P0140   16524   02 Sensor Circ., Bank1-
Sensor2  
No Activity Detected 
2)    
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 27 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 28 of 166

01-24
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0150   16534   02 Sensor Circ., Bank2-
Sensor1  
Malfunction 
2)  - Check oxygen sensor control or oxygen sensor heater and wiring   
Page 24
-79
 
P0151   16535   02 Sensor Circ., Bank2-
Sensor1  
Low voltage 
2)    
P0152   16536   02 Sensor Circ., Bank2-
Sensor1  
High Voltage 2)    
P0153   16537   02 Sensor Circ., Bank2-
Sensor1  
Slow Response 2)    
P0154   16538   02 Sensor Circ., Bank2-
Sensor1  
No Activity Detected 
2)    
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 28 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 29 of 166

01-25
 
DTC  
Description of 
malfunction  
Corrective action  
SAE  
VAG  
  
  
P0156   16540   02 Sensor Circ., Bank2-
Sensor2  
Malfunction 
2)  - Check oxygen sensor heater   Page 24
-114
P0157   16541   02 Sensor Circ., Bank2-
Sensor2  
Low Voltage 
2)  - Check oxygen sensor signal wire and activation   Page 24
-122
P0158   16542   02 Sensor Circ., Bank2-
Sensor2  
High Voltage 
2)    
P0159   16543   02 Sensor Circ., Bank2-
Sensor2  
Slow Response 2)  - Check oxygen sensor and oxygen sensor control behind catalytic 
converter  Page 24
-100
 
P0160   16544   02 Sensor Circ., Bank2-
Sensor2  
No Activity Detected 
2)  - Check oxygen sensor heater   Page 24
-114
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 29 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 30 of 166

01-26
 
DTC  
Description of 
malfunction  
Corrective action  
SAE  
VAG  
  
  
P0236   16620   Charge air pressure 
sensor -G31-  
Implausible signal   Repair Manual, 2.7 Liter V6 5V BiTurbo Engine Mechanical, Engine Code(s): 
APB, Repair Group 21; Boost pressure system with turbocharger; charge air pressure sensor 
-G31
-, checking
   
P0237   16621   Turbocharger Boost 
Sensor (A) Circ  
Low Input 
2)   Repair Manual, 2.7 Liter V6 5V BiTurbo Engine Mechanical, Repair Group 21; 
Turbocharger; Checking Charge Air Pressure Sensor -G31   
P0238   16622   Turbocharger Boost 
Sensor (A) Circ  
High Input 
2)    
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
Pa
ge 30 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 31 of 166

01-27
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0300   16684   Random/Multiple Cylinder  
Misfire Detected
2)  - Check cause for misfire   Page 28
-52
P0301   16685  
Cyl.1 Misfire Detected 
2)  
- Check fuel tank level
P0302   16686  
Cyl.2 Misfire Detected 2)  
  
P0303   16687  
Cyl.3 Misfire Detected 2)  
  
P0304   16688  
Cyl.4 Misfire Detected 2)  
  
P0305   16689  
Cyl.5 Misfire Detected 2)  
  
P0306   16690  
Cyl.6 Misfire Detected 2)  
  
2) With this malfunction the exhaust Malfunction Indicator Light (MIL) is only switched on by the ECM, if the malfunction is 
recognized after the engine has been restarted. Significance of MIL   Page 01
-3 .  
The Malfunction Indicator Light (MIL) will blink if the Engine Control Module (ECM) recognizes misfire that could damage the 
catalytic converters. 
Notes:  
 
On malfunction which could be caused by lack of fuel (e.g.: misfire) the malfunction P1250 "Fuel level too low" will be 
displayed in addition. That means, the misfiring was detected due to lack of fuel in the tank and not due to a technical 
malfunction. 
Pa
ge 31 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1 
Page 33 of 166

01-28
 
DTC  
Description of malfunction  
Corrective action  
SAE  
VAG  
  
  
P0321   16705   Ign./Distributor Eng. Speed Inp. Circ.  
Range/Performance
2)  - Check Engine Speed Sensor   Page 28
-21
P0322   16706   Ign./Distributor Eng. Speed Inp. Circ.  
No Signal 
2)    
P0327   16711   Knock Sensor 1 Circ.  
Low Input  - Check Knock Sensor   Page 28
-41
P0328   16712   Knock Sensor 1 Circ.  
High Input    
P0332   16716   Knock Sensor 2 Circ.  
Low Input    
P0333   16717   Knock Sensor 2 Circ.  
High Input    
P0341   16725   Camshaft Pos. Sensor Circ.  
Range/Performance 
2)  - Check Camshaft Position Sensor   Page 28
-45
P0346   16730   Camshaft Pos. Sensor Circ. 2  
Range/Performance 
2)    
Pa
ge 33 of 166 Motronic s
ystem, On Board Dia
gnostic 
(OBD
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU04.01.1