wiring AUDI A4 2000 B5 / 1.G ATQ Engine Ignition System Checking Workshop Manual

28-2

Safety precautions

To reduce the risk of personal injury and/or
damage to the fuel injection and ignition system,
always observe the following:

Do not touch or pull off ignition wires when
engine is running or turning at starting RPM.
Always switch ignition off before disconnecting
or reconnecting wires for the injection and
ignition system, including high voltage wiring
and test leads.
If engine is to be cranked at starting RPM
without starting (e.g. for compression testing),
disconnect connector from ignition coils and
from fuel injectors.
It is possible that the control module will
recognize a malfunction and store a DTC during
some tests. After completing all tests and
repairs, DTC memory should therefore be
checked and erased if necessary. Readiness
code must be generated after DTC memory is
erased Page 01
-82
.

Always switch ignition off before cleaning
engine.
Pa
ge 2 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-10

Checking Ground (GND) supply of power
output stage

If LED does not light up:
Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
2 B+

LED must light up.
- Check the wire connection for open circuit:
- Repair open circuit if necessary.
Pa
ge 12 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-11

Checking voltage supply to ignition coils

Note:
Voltage is supplied to ignition coils via Fuel
Pump (FP) relay.

Test requirement:

Fuse for ignition coils OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder

If LED does not light up: - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Engine Ground (GND)
- Operate starter.

LED must light up.
- Check the wire connection for open circuit:
Pa
ge 13 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

Electrical Wiring Diagrams, Troubleshooting & Component Locations
binder - Repair open circuit if necessary.
Pa
ge 14 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-12

Checking activation

- Disconnect connectors from all six fuel injectors.
(afterward check DTC memory)

If specified values are not obtained: - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
3 Engine Ground (GND)
4 Engine Ground (GND)
5 Engine Ground (GND)
- Operate starter for a few seconds.

LED must blink (brief blink signal).
- Switch ignition off.
- Connect VAG1598/31 test box at wiring harness to ECM, do not
connect ECM Page 24
-17
.
Pa
ge 15 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-17

Checking wire connections

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

- Check the following wire connections for open circuit and short circuit
to Ground (GND) and B+: Harness connector
Terminal
VAG1598/31 test box
Socket
1 85
2 108
- Check both wires to each other for short circuit.
- Repair open circuit or short circuit if necessary.
Pa
ge 20 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-21
If specified value is not obtained:

- Replace engine speed (RPM) sensor.
If specified value is obtained:

If specified value is not obtained:
If specified value is obtained: - Connect multimeter to terminals 2 and 1 (shielding) and to terminals 3
and 1 (shielding) for resistance measurement.

Specification: each (no continuity)
- Replace engine speed (RPM) sensor.
- Connect VAG1598/31 test box at wiring harness to ECM, do not
connect ECM Page 24
-17
.
Pa
ge 24 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-27

All models
Range A shows the resistance values for the
temperature range from 0-50 C, and range B
shows the values for the temperature range from
50-100 C.

Read-out examples:
If specified value is not obtained:
If specified value is obtained:
30 C corresponds to a resistance of 1500 to 2000 80 C corresponds to a resistance of 275 to 375
- Replace coolant temperature sensor.
- Connect VAG1598/31 test box at wiring harness to ECM, do not
connect ECM Page 24
-17
.
Pa
ge 30 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

28-31

Test requirements:

Fuse for Engine Control Module (ECM) OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder

Battery voltage at least 12.7 V
Generator OK

Test sequence

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

- Switch ignition on.

Note:

The plus voltage supply for the Engine Control
Module (ECM) travels via connector terminal 3
(terminal 15) and connector terminal 62
(terminal 30).
Ground (GND) supply of the Engine Control
Pa
ge 34 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1

- Check wire connections.

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder
Pa
ge 37 of 65 I
gnition s
ystem, checkin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.28.1