engine AUDI A4 2000 B5 / 1.G ATQ Engine Motronic Injection System Servicing Owner's Manual

Note:
Pressure increase for an engine at operating
temperature limited by the fuel expansion is
normal.
Pa
ge 40 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-34

- Start engine and let run at idle.

The following malfunction are possible if the pressure does not drop:
Repair Manual, Fuel Supply System, Repair Group 20; Fuel supply
-
Front Wheel Drive or fuel supply
- All Wheel Drive

Note:
Pressure gauge displays the pressure behind the stopcock "intake
manifold side" after the stopcock is closed (in direction of fuel injector, fuel
pressure regulator). If the pressure drops in front of the stopcock (in
direction of fuel tank), the device cannot detect it. For this reason, the
center of this page states "If the pressure does not drop...". - Wait until pressure has dropped, and then switch off ignition.
Simultaneously close shut-off valve of VAG1318 pressure gauge (lever
perpendicular to direction of flow -arrow-).
There is a leak in the threaded connection between the pressure
gauge and the fuel supply line There is a leak at the supply line at fuel tank.There is a leak in the check valve in the Fuel Pump (FP).
Pa
ge 41 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-37

Checking internal resistance

- Remove engine cover (arrows).
- Disconnect harness connector at the fuel injector to be tested.

With an engine at operating temperature, the resistance increases by
approx. 4 to 6 .
If specified value is not obtained: - Connect multimeter at valve for resistance measurement.

Specification: 13.5 to 15.5
- Replace fuel injector Page 24
-43
.
Pa
ge 44 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-38

Checking voltage supply

Test requirements:

Fuel Pump (FP) OK, checking Page 24
-
49
.

Fuse for fuel injectors OK

Electrical Wiring Diagrams, Troubleshooting &
Component Locations binder

- Disconnect harness connector at the fuel
injector to be tested.

If LED does not light up: - Connect VAG1527B voltage tester as follows:Harness connector
Terminal
Measure to
1 Engine Ground (GND)
- Switch ignition on.

LED must light up.
Pa
ge 45 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-39

- Repair open circuit if necessary.
If LED lights up:

Checking activation

Test requirement:

Internal resistance of valve OK

Note:
Voltage testers do not go out completely during low current pick-up
between activations by the ECM, but rather continue to glow a little and
then get slightly brighter during activation. - Slide back rubber grommet of fuel injector connector (arrow), but leave
connector connected.
- Connect VAG1527B voltage tester between sockets 2 (signal) and 1
(B+).
- Operate starter briefly (engine can also start).

LED must blink.
Pa
ge 47 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-40
If LED does not blink:

- Connect VAG1598/31 test box at wiring harness
to ECM, do not connect ECM Page 24
-17
.

If wire connection is OK: - Check the following wire connections for open circuit and short circuit
to Ground (GND) and B+: Cylinder
Fuel injector harness connector
Terminal
VAG1598/31 test box
Socket
1 2 96
2 2 112
3 2 88
4 2 97
5 2 113
6 2 89
- Repair open circuit or short circuit if necessary.
- Replace Engine Control Module (ECM) Page 24
-21
.
Pa
ge 48 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-41


Fuel rail with fuel injectors, disassembling
and assembling

1 -
Fuel distributor
2 -
to T-piece
3 -
Retaining clip
Check for secure fitting
4 -
O-ring Removing and installing Page 24
-43
Always replaceCoat with clean engine oil
5 -
Fuel pressure regulator
Pa
ge 49 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-42


6 -
O-ring
Removing and installing Page 24
-43
Always replaceCoat with clean engine oil
7 -
Fuel injectors -N30- through -N33-
,Cylinder 5/6 Fuel Injector -N83-, -N84- Removing and installing Page 24
-43
8 -
Retaining clip
Make sure clip is correctly seated on fuel
injector and fuel rail
Pa
ge 50 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-43

Fuel injectors, removing and installing


- Remove engine cover (arrows).
- Remove intake air hose between Mass Air Flow (MAF) sensor and
intake air elbow.
- Remove all harness connectors to injectors.
- Disconnect vacuum hose from fuel pressure regulator.
- Expose wires at fuel distributor.

WARNING!
Fuel system is under pressure! Place a cloth around the connection
point before opening system. Then release pressure by carefully
loosening connection point. - Unscrew fuel distributor from intake manifold (arrows) .
- Remove fuel distributor with injectors from intake manifold
simultaneously upward and set aside in rear of engine compartment on
a clean cloth.
Pa
ge 51 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1

24-44

- Disengage retaining clip and remove fuel
injector.

Note:
Fuel lines must be disconnected before replacing
fuel distributor.
Installation is reverse of removal, noting the
following:

Remove O-rings at all opened connections.
(Never remove plastic cap from valve head
to replace front O-ring - pry O-ring off over
plastic cap).
Lightly lubricate O-rings with clean engine
oil.
Make sure fuel injectors are in place and
seated correctly
Check clip for unobstructed fitting.
Place fuel rail with secured fuel injectors
onto intake manifold, and apply uniform
pressure to press it in.

Tightening torque
Pa
ge 52 of 78 Motronic in
jection s
ystem, servicin
g
11/23/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU05.24.1